In recent years, walk-behind tractors for cultivating summer cottages have become popular. In order not to do most of the work with your hands, you purchase some model of a walk-behind tractor on which you can install additional equipment, especially since the use of large technical devices in a small area is not advisable. Various models of devices are known, differing in their narrow specialization, but helping to solve many problems. Such devices include the MF 70 walk-behind tractor produced by a Czech company.
Specifications
The MF 70 mower has moderate technical characteristics:
- width of the area to be processed – 14 cm
- blade width during operation – 8 cm
- productivity – 0.3 ha/hour
- highest speed during operation – 2.5-3 km/h
- highest forward speed during transportation – 6.9 km/h
- highest rear speed during transportation – 2.3 km/h
These indicators are acceptable for personal farming.
Structure of the MF 70 walk-behind tractor
Engine characteristics
The equipment is equipped with a single-cylinder, two-stroke, air-cooled engine. The fuel and air are supplied by the carburetor. A manual starter is installed for starting. Basic indicators:
- traction power – 5 hp
- volume – 218 cm3
- number of gears (forward/rear) – 2/1
Fuel consumption
The fuel tank capacity is 5 liters. The consumption when mowing grass is 5 liters per hectare.
Motor mower MF-70
Nowadays, the entire range of work on a small plot can be performed with a walk-behind tractor, using all kinds of interchangeable working parts: cutters, plows, planters, hillers, etc. In fact, a walk-behind tractor with a large number of attachments is a universal unit. But in addition to walk-behind tractors, highly specialized small equipment was also produced. An example of this is the MF 70 motorized mower.
The MF 70 motor mower was produced by the Czech company Agrozet. This company was engaged in the production of small agricultural machinery, as well as agricultural equipment. units since the post-war period.
The MF 70 mower was intended for mowing soft grass, it could be used for snow removal work, and it could also carry out transport work, although the mass of the transported cargo was not that large.
Device
The Czech walk-behind tractor MF 70 has an unusual design. The gearbox housing on which the engine is located is responsible for the load-bearing function. The transmission is contained behind. On both sides of the gearbox there are wheel flanges into which the brake equipment is inserted. The power take-off shaft is installed in front of the gearbox. It can be used to use other attachments. The steering is located on the gearbox. Shifting gears and clutch is done using the steering wheel. A special feature of this technique is the ability to change the steering height.
Be sure to read: Cultivator for tractor MTZ 82
Description
The Czech narrow-directional mower MF 70 is suitable for improving land or garden plots. It has less weight and size compared to massive walk-behind tractors, but is similar in appearance to them. The walk-behind tractor has been used on the farm for many years and solves problems from mowing grass to plowing the land. But it is not entirely convenient if we are talking about a small garden plot, which contains mainly fruit trees, flowers and berry bushes.
In addition, a walk-behind tractor is a rather expensive type of small agricultural equipment, unlike a brush cutter, which does not have a large number of interchangeable working parts (hiller, plow, cutter, etc.), which are sometimes not used on a specific plot of land. The brush cutter is produced by a Czech company Agrozet, which has experience in producing it and other small units for more than half a century.
The mower helps to cope with mowing the grass in areas
The purpose of this highly targeted equipment is to mow soft grass and remove snow, but the working body allows you to transport small loads and remove leaves. The design and size features allow you to carefully mow and remove snow in narrow places, for example, between trees or in a hard-to-reach corner of the site. This model has become widespread in Russia, so you can buy it used. or it’s easy to find replacement parts for it.
To get a more complete impression of the mower, it is necessary to highlight its disadvantages and advantages.
Advantages and disadvantages
The features of the mower make it possible to highlight the positive and negative aspects of this small-sized equipment.
Advantages:
- small size;
- functionality;
- works in bottlenecks of the site;
- availability of replacement spare parts for sale;
- durability of parts and assemblies;
- not difficult to operate;
- low cost.
Flaws:
- small fuel tank;
- not suitable for mowing hard grass;
- limited technical capacity.
Features of the mower device
The Czech mower MF 70 differs from other mowers in its non-standard design . It is based on the gearbox housing. It performs a load-bearing function. On its rear side there is a gearbox, used for conveniently switching the mowing speed when performing work, and a power unit is mounted that drives it. On the sides of the body there are wheel flanges with built-in brake mechanisms. In the front part of the unit there is a power take-off shaft (PTO), which also performs the function of attaching the mower’s mounted working parts to change its functions.
Mower device
The steering control of the mower is located on top of the gearbox housing. It is adjustable in height, which is very convenient, since the work is carried out by people of different heights and different builds, to whose parameters an anatomical adjustment can be made. This will allow you to work without interruptions. The steering wheel of the brush cutter also controls the gearbox, accelerator, clutch, and brake system, which allows you to change the operating speed without turning off the engine. The power plant is a two-stroke, single-cylinder unit, attached vertically. Unit model 1z22.
The MF 70 mower has a distinctive feature - air cooling. Thanks to it, you can work in hot climates without interruption to cool the power unit from overheating. The fuel injection system is carburetor type, the reliability of which ensures a long service life. The mower is started manually using a starter. The mower has three speeds - 2 main and one reverse. Shifting is carried out thanks to a reliable friction clutch when transmitting torque.
One of the conveniences is the presence of pneumatic wheels. The working body is segment-finger, which is based on cutting and load-bearing parts. They are equipped with a drive mechanism, which allows you to mow efficiently in one go. This does not damage the grass or tear it out with its root system. Before work, it is possible to adjust the mowing height using support units. Maximum height 14 cm.
An important feature is that the drive of the brush cutter is located inside the body and is protected from the effects of water and other external factors, which will allow you to use it for a long time without repair and cleaning it from sand and grass.
Instead of a mowing unit, a bucket or a snow blower or a rotary mower can be installed on the mower. The trailer mount for transporting small loads is located under the power unit.
Advantages and disadvantages
Although the mower has little power, it has many advantages:
- small design;
- ability to perform many functions;
- mobility;
- easy controls;
- low cost.
The disadvantages of the technology include:
- low output;
- Difficulties in cleaning tough grass;
- limited selection of spare parts and components.
Czech walk-behind tractor MF 70
Mower cost
When purchasing a device, you should remember that this model is produced by a Czech manufacturer this year. The cost as of 2022 varies from 45 to 100 thousand rubles. You can buy a used Czech mower MF 70 at a cost of 20 thousand rubles. It is important to take into account its condition. Sometimes a rusty, but working model can be purchased for a small amount, but such a unit will not last long, since rust could penetrate into the engine or fuel tank.
A model that requires minor repairs can be purchased, since there is a large assortment of spare parts in stores. The most profitable purchase will be with delivery in any online store. There are also many announcements about the repurchase of this model, which indicates its wide popularity among consumers.
When deciding to purchase a helper for your garden plot, you should consider the model of the Czech MF 70 mower, which is popular among consumers solely for its positive qualities.
This is explained by the manufacturer’s more than 50 years of experience in its production and simplicity of design, as well as low maintenance costs and the purchase of consumable spare parts. Facebook
Connection and rules for using the mower
The device is easy to connect and configure, allowing it to be successfully used even by novice users. As a rule, detailed recommendations for preparing the product for use are contained in the instructions included with new models.
You will need to mount the drive mechanism on the PTO, and also secure the housing using a pin. If you plan to remove snow or debris, you will need to install an auger snow blower, bucket or other attachment. You can mount a trailer on the device, which will simplify the transportation of goods up to 30 kg.
TZ-4K-14.Mini tractors from the Czech Republic
The structure of the MF-70 two-stroke gasoline engine
1. The cutting apparatus assembly is medium.
No. | License number | Catalog number | Part name | knife140 | knife120 |
X | 9-5073-202 | Cutting device 140cm | 1 | ||
X | 9-5073-204 | Cutting device 120cm | 1 | ||
X | 9-5066-211 | Double finger assembly | 13 | 11 | |
1 | 0-9025-202 | Finger screw | 14 | 10 | |
2 | 0-5066-201 | Double finger | 13 | 11 | |
3 | 0-5032-203 | Liner | 26 | 22 | |
4 | NA 438 | Rivet 5x25 | 26 | 22 | |
5 | 0-9025-201 | Finger screw | 4 | 4 | |
X | 9-5063-202 | Left outer shoe | 1 | 1 | |
6 | 0-5063-202 | Left outer shoe | 1 | 1 | |
7 | 0-5032-201 | Left insert | 1 | 1 | |
8 | NA 438 | Rivet 5x17 | 1 | 1 | |
9 | NA 438 | Rivet 5x22 | 1 | 1 | |
X | 9-5063-201 | Right outer shoe assembly | 1 | 1 | |
10 | 0-5063-201 | Outer shoe right | 1 | 1 | |
11 | 0-5032-202 | Right insert | 1 | 1 | |
12 | 0-9016-202 | Shoe screw (bolt) | 1 | 1 | |
X | 021740.00 | Washer 10 | 6 | 4 | |
X | 021401.20 | Nut M10 | 4 | 4 | |
X | 9-5030-202 | Timber assembly | 1 | — | |
X | 9-5030-204 | Timber assembly | — | 1 | |
13 | 0-5030-236 | Finger beam 140S | 1 | — | |
X | 0-5030-281 | Finger beam 120S | — | 1 | |
14 | 0-9326-201 | Support rod | 1 | 1 | |
15 | 02 2311.9 | Rivet 14x32 | 2 | 2 | |
16 | 02 2311.9 | Rivet 14x40 | 1 | 1 | |
17 | 0-9510-202 | Emphasis | 2 | 2 | |
18 | 022311.00 | Rivet 6x34 | 2 | 2 | |
19 | 0-9464-204 | Left clamp | 2 | 2 | |
20 | 0-9464-205 | Right clamp | 2 | 2 | |
21 | 0-9025-203 | Pull bolt | 4 | 4 | |
22 | 0-9440-211 | Guide | 4 | 4 | |
23 | 0-92332-203 | Adjusting washer 0.2 | |||
X | 0-9232-202 | Adjusting washer 0.4 | |||
X | 0-92332-201 | Adjusting washer 0.6 | |||
24 | 0-9025-204 | Clamp bolt | 8 | 8 | |
25 | 9-5042-201 | Left skid assembly | 1 | 1 |
X | 0-5042-204 | Left skid | 1 | 1 |
X | 0-1540-291 | Heel runner | 1 | 1 |
X | 02 2311.00 | Rivet 6x20 | 2 | 2 |
26 | 9-5042-202 | Right skid assembly | 1 | 1 |
X | 0-5042-203 | Right skid | 1 | 1 |
X | 0-1340-202 | Heel runner | 1 | 1 |
X | 02 2311.00 | Rivet 6x20 | 2 | 2 |
27 | 0-9016-201 | Bolt slide | 2 | 2 |
X | 021740.00 | Washer 12 | 2 | 2 |
X | 1401-20 | Nut M12 | 2 | 2 |
28 | 0-3715-201 | Dog | 1 | 1 |
29 | 0-9746-202 | Spring 5 | 1 | 1 |
30 | 0-9311-400 | Cork | 1 | 1 |
31 | 472 | Safety ring 23x1.2K | 1 | 1 |
X | 9-5064-201 | Moldboard lion assembled | 1 | — |
X | 9-5064-205 | Dump board left. Assembled | — | 1 |
32 | 9-5064-203 | 1 | 1 | |
X | 0-5042-202 | Left dump board | 1 | 1 |
X | 0-5032-218 | Covering the dump board | 1 | 1 |
X | 02 2301.1 | Board headRivet 5x12 | 8 | 4 |
33 | 0.5016-201 | Knitsa | 2 | 2 |
34 | 02 1319 | Bolt M8x25 | 2 | 2 |
X | 02 1721. 00 | Washer 9 | 2 | 2 |
X | 02 1401.20 | Nut M8 | 2 | 2 |
35 | 02 1319 | Bolt M8x45 | 2 | 1 |
X | 02 1740.00 | Washer 8 | 4 | 2 |
X | 02 1401.20 | Nut M8 | 2 | 2 |
X | 9-5064-202 | Dump board assembled pav. | 1 | — |
X | 9-5064-206 | Dump board assembled rights | — | 1 |
36 | 9-5064-204 | Dump board right | 1 | 1 |
X — | 0-5042-201 | Sheet covering of the dump right board | 1 | 1 |
X | 0-5032-218 | Board head | 1 | 1 |
37 | 0-9015-201 | Bolt | 2 | 2 |
38 | 0-9746-201 | Spring 4 | 2 | 2 |
39 | 02 1411.20 | Nut M12 | 2 | 2 |
X | 02 1781.00 | Cotter pin 3.2x25 | 2 | 2 |
40 | 9-5037-240 | Knife 140 cm | 2 | — |
X | 9-5037-223 | Knife 120 cm | — | 2 |
41 | 0-5030-201 | Knife back 140cm | 2 | — |
X | 0-5030-280 | Knife back 120cm | — | 2 |
42 | 0-5030-202 | Cutter | 32 | — |
X | 0-5030-804 | Cutter 15.5 | — | 24 |
43 | 0-5030-203 | Cutter to drive | 4 | 4 |
44 | 0-9440-214 | Spatula (removal) | 8 | 8 |
45 | NA 438 | Rivet 5x14 | 56 | 48 |
46 | NA 438 | Rivet 5x18 | 16 | 16 |
X | 9-8549-238 | Cutter housing assembly | 1 | — |
X | 9-8549-228 | Cutter housing assembly | — | 1 |
47 | 9-8542-201 | Cutter housing | 1 | — |
X | 9-8542-230 | Cutter housing | — | 1 |
48 | 0-9746.203 | Spring 1.6 | 2 | 2 |
X | 0.9245.201 | Fuse 2.5 | 2 | 2 |
2.Carburetor.
No. | License number | Catalog no. | Name | Things |
X | 978-0325 | 443 753 279 200 | Carburetor 2923PH | 1 |
49 | 937-0149 | 443 919 370 149 | Carburetor body | 1 |
50 | 706-0930 | 443 915 560 930 | Spool chamber cover | 1 |
51 | 103-3603 | 443 911 033 603 | Cable guide | 1 |
52 | 130-0114 | 443 911 300 114 | screw | 1 |
53 | 737-0429 | 443 915 870 429 | Spool | 1 |
54 | 209-1813 | 443 912 091 813 | Spool needle | 1 |
55 | 601-3704 | 443 916 013 704 | Needle guard | 1 |
56 | 134-0387 | 315 116 133 270 | Spool spring | 1 |
57 | 101-4805 | 443 911 014 805 | Spool thrust bolt | 1 |
58 | 101-4902 | 443 911 014 902 | Adjustment bolt | 1 |
59 | 134-0123 | 315 116 095 070 | Spring | 2 |
60 | 32 050 00 | 443 911 131 050 | Idle jet | 1 |
61 | 22 098 00 | 443 911 122 098 | Main jet | 1 |
62 | 934-0124 | 443 919 340 124 | Needle valve complete | 1 |
63 | 625-0248 | 722 923 110 101 | Seal 5.5/2.5 | 1 |
64 | 913-0150 | 273 111 014 194 | Ring 42x2 | 1 |
65 | 946-0133 | 443 919 460 133 | Complete float | 1 |
66 | 201-0154 | 443 912 010 154 | Suspension axis | 1 |
67 | 711-1313 | 443 915 611 313 | Float chamber | 1 |
68 | 101-0801 | 443 911 010 801 | Bolt | 2 |
3.Starter.
No. | License number | Catalog no. | Name | Things |
X | 984-0816 | Set Starter | 1 | |
69 | 101-2465 | Screw | 1 | |
70 | 601-2301 | Drive disc | 1 | |
71 | 134-0388 | Spring | 1 | |
72 | 780-3802 | Dog | 3 | |
73 | 601-1902 | Retaining ring | 3 | |
74 | 602.5031 | Pad | 1 | |
75 | 134-1102 | Spring | 3 | |
76 | 846-4101 | Wolf brace | 1 | |
77 | 913-3207 | Cable | 1 | |
78 | 913-6501 | Start handle | 1 | |
79 | 930-5504 | Return spring | 1 | |
80 | 718-2604 | Starter housing | 1 | |
81 | 301-1727 | Sleeve | 1 | |
82 | 02 1702.19 | Washer 8.4 | X | |
X | 02 1103.59 | Screw | X | |
83 | 301-728 | Sleeve | 1 |
4.Drive mechanism.
No. | License number | Catalog no. | Name | Things |
84 | 02 9401.0 | Seal 40x52x7 (oil seal) | 1 | |
85 | 00.20.046 | 0-9220-060 | Pad | 2 |
86 | 02 4636 | Bearing 6205 | 1 | |
87 | 76.19.063 | 0-3014-002 | Primary shaft | 1 |
88 | VNZ 15x13 | Bushing VGZ 15x13 | 1 | |
89 | 02 2930 | Safety ring 15x1 | 1 | |
90 | 82.19.025 | 9-9220-059 | Pad | 2 |
91 | 76.19.050 | 0-3020—002 | Reverse gear 60 | 1 |
92 | 9-9471-201 | Needle bearing 15x19x24 | 1 | |
93 | 76.19.088 | 532-0-9520-007-3 | Ring 28 | 1 |
94 | 76.19.068 | 532-0-3815-002-3 | Val 16 | 1 |
95 | 02 1185.21 | Bolt M 6x16 | 1 | |
96 | 532-0-9847-002-3 | Lid | 1 | |
97 | 02 4636 | Bearing 6206 | 1 | |
98 | 76.19.052 | 0-3012-002 | Drive gear | 1 |
99 | 02 4731 | Axial bearing 51202 | 1 | |
100 | 75.19.064 | 0-3024-003 | Secondary shaft gear | 1 |
101 | By 15/13 | Needle bearing INA K15/13 | 1 | |
102 | 19x1 | Safety ring 19x1 | 1 | |
103 | 76.19.086 | 0-3214-006 | Worm shaft | 1 |
104 | 00.20.150 | 0-9220-057 | Gasket 40x0.1 | 1 |
X | 0-9220-056 | Gasket 40x0.2 | 1 | |
105 | 02 4644 | Bearing 7204 B | 1 | |
106 | 76.19.062 | 0-9813-001 | Cover 50 | 1 |
107 | 00.25.043 | 0-9635-003 | Ring "O" | 1 |
108 | 02 3680 | Ball 7 | 1 | |
109 | 00.30.031 | 0-0746-012 | Compression spring | 1 |
110 | 02 1181.21 | Safety screw M10x10 | 1 | |
111 | 0-9016-019 | Screw M8x10 | 1 | |
112 | 76.19.016 | 0-3750-001 | Power plug | 1 |
113 | 00.25.025 | 0-9635-001 | Ring "O" | 1 |
114 | 76.19.017 | 0-8547-014 | Sealing ring | 1 |
115 | 76.19.832 | 9-3815-001 | Switching shaft | 1 |
116 | 02 2173 | Pin 3x20 | 2 | |
117 | 02 2930 | Retaining ring 48x1.75 | 1 | |
118 | 76.17.004 | 532-03720-003-3 | Pressure pad | 1 |
119 | 00,26.001 | 532-0-3720-002-3 | Internal plate | 7 |
120 | 00.26.026 | 532-0-3726-002-3 | Outer plate | 10 |
121 | 02 1103.24 | Bolt M6x30 | 1 | |
X | 02 1740.04 | Spring washer 6.1 | 1 |
122 | 701.20.316.00 | 532-0-3832-004-3 | Pressure ring | 1 |
123 | 701.20.317.00 | 532-0-3620-002-3 | Friction ring | 1 |
124 | 76.17.003 | 523-0-8547-013-3 | Pressure plate | 1 |
125 | 75.19.208 | 532-0-8547-012-3 | Spring ring | 1 |
126 | 00.30.036 | 532-0-9746-011-3 | Spring 3.3 | 1 |
127 | 76.17.002 | 532-0-3625-001-3 | Clamping sleeve 50 | 1 |
128 | 75.19.005 | 532-0-3744-001-3 | Switching bracket | 1 |
129 | 00.99.295 | 532-0-9745-002-3 | Spring | 1 |
X | 9-3282-010 | Gearbox assembly | 1 | |
X | 9-3253-001 | Transmission | 1 | |
130 | 76.19.834 | 0-3253-008 | Transmission | 1 |
131 | 02 1176.24 | Bolt M8x25 | 1 | |
X | 02 1176.24 | Bolt m8x30 | 1 | |
132 | 76.19.813 | 9-8815-002 | Oil meter | 1 |
134 | 00.25.040 | 02 9281.2 | Ring 18x2 | 1 |
135 | 02 2931 | Safety ring 52x2 | 1 | |
136 | 76.19.029 | 0-9520-008 | Sleeve | 1 |
137 | 02 4636 | Bearing 6205 | 1 | |
138x x | 00.20.118 | 0-9220-0620-0220-063 0-9220-064 | Gasket 40x0.1 Gasket 40x0.2 Gasket 40x0.3 | |
139 | 76.19.807 | 9-3225-001 | Worm wheel | 1 |
140 | 76.19.011 | 0-3812-005 | Val 28 | 1 |
141 | 02 2562 | Key 8e 7x7x50 | 1 | |
142 | 76.19.834 | 0-3253-007 | Gearbox (transmission) right | 1 |
143 | 02 9401.0 | Seal 35x52x12 | 1 | |
144 | 76.19.090.0 | 0-8521.001 | casing | 2 |
X | 9-1629-202 | Left ring | 1 | |
145 | 0-9240-201 | Fastening | 2 | |
146 | 02 1401.24 | Nut M 20x1.5 | 2 | |
147 | 02 1176.24 | Bolt M 10x25 (stud) | 1 | |
148 | 02 1176.24 | Bolt M 10x35 | 2 | |
149 | 75.17.006 | 0-9816-001 | Guide bolt | 2 |
150 | 02 1101.24 | Bolt M8x80 | 1 | |
151 | 00.02.078 | 532-0-9016-017 | Bolt | 2 |
152 | 0-9010-027 | Bolt 7 x11 | 3 |
No. | License number | Catalog no. | Name | Things |
X | 02 1703.11 | Washer B 10.5 | 2 | |
X | 02 1401.21 | Nut M 10 | 2 | |
X | 02 1740.04 | Spring washer 8.2 | 11 | |
X | 02 1401.24 | Nut M8 | 11 | |
154 | 76.19.056 | 0-8548-008 | Wheel flange right | 1 |
155 | 76.19.057 | 0-8548-007 | Wheel flange left | 1 |
156 | 00.75.058 | Pneumatic tire 4.00x8 | 2 | |
157 | 0-1624-202 | Disc wheel | 2 | |
X | 9-1629-201 | Right wheel | 1 | |
158 | 0-9026-201 | Screw | 1 | |
X | 02 1401.24 | Nut M8 | 1 | |
X | 0-9746-205 | Compression spring | 1 | |
159 | 0-9026-202 | Clamp | 1 | |
X | 02 1103.54 | Screw M6x10 | 1 | |
160 | 9-1721-201 | Brake disk | 1 | |
161 | 9-8043-212 | Brake band | 1 | |
162 | 02 1740.00 | Safety ring 8 | 3 | |
163 | Tire | 2 |
5.Engine.
6. Crank device.
7. Ignition.
8.Fan.
9.Cylinder .
10.Fuel tank.
11.Air filter.
12.Reflective glass.
13.Cutting mechanism .
14.Control handles.
Drawings of pullers for repair and maintenance mower engines: |
Dimensions
Consumers prefer small-sized models of mowers due to the fact that they cannot always provide storage for large units in their garden plot.
The Czech mower has the following dimensions:
- Width 140 cm.
- Length 175 cm.
These dimensions are more convenient for storage compared to massive walk-behind tractors. They will also allow you to mow the grass around bushes and fruit trees or remove snow on narrow garden paths.
Where to buy and how much does a walk-behind mower cost?
Removing snow with a walk-behind tractor MF-70
The Czech model in Russia is sold with a slight markup. Moreover, they offer fm 70 via the Internet and directly in specialized salons. We offer the reader several proven companies in major Russian cities:
Cities | Name and contact details of the seller's company | Price for fm 70 mower |
Moscow | “Everything for the garden”, st. Krasnoflotskaya, 25, office 4, tel.: 8(926)212-91-03 | 100 000 |
Nizhny Novgorod | “Tools for the garden”, st. Molodezhnaya 12, office 12 | 110 000 |
Kazan | “Motoprof”, st. Lenina, 41, of. 24, tel.: 223-34-13 | 110 000 |
St. Petersburg | “Profi”, st. Skladskaya, 48, tel.: 725-234-12 | 115 000 |
Rostov-on-Don | “Agroserver”, st. Pushkina, 25, tel.: 23-12-45 | 125 000 |
A lot of used equipment is sold in all cities. The price for a mower made before 1995 is from 40,000 rubles, models before 2000 cost from 75,000 rubles. The price depends on the operation, condition and storage of the equipment. In the presented companies, the reader will be able to purchase not only Czech motorcycles, but also spare parts for them.
If you decide to buy a helper for your home, then the Czech fm 70 mower will be a real find. You can try placing an ad in newspapers and websites saying that you want to buy equipment. Some old villages have had similar models since the 70s. Their condition is quite decent, and the price will be low. But before purchasing, inspect the mower for hidden damage. Modern spare parts will fit older models, but they will have to be ordered online.
How do you like the article?
Pros and cons of technology
Despite its low power and modest technical performance, the mower can be used for many types of work in a small private household. And even a woman can handle the controls.
The advantages of the fm 70 mower include:
- Small sizes;
- Functionality;
- Mobility;
- Affordable price.
The disadvantages include:
- Low productivity;
- Does not cope with tough vegetation;
- It is difficult to buy some components and spare parts.
Reviews of the mower are mainly related to its technical characteristics and build quality:
Reviews say that the walk-behind mower is suitable for households where it is necessary to tidy up the local area or clear vegetation from fruit trees and berry fields. To harvest grass for feed and to clean small bushes, it is better to buy a walk-behind tractor with special equipment.
Czech walk-behind tractor MF-70
Sanjok wrote: Yesterday I was mowing my MF and after 30 minutes of work the connecting rod jammed on the crankshaft. I added XADO 2 T oil to gasoline in the ratio of 30 grams of oil per 1 liter of gasoline. I think the reason is the oil, since until this year it ran on regular diesel oil. Who can tell me something about this.
Sanjok, Lew in a ratio of 1:40, gasoline 92 and semi-blue oil or mineral water from the leftovers. For 4 liters of gasoline, 100 ml of oil, + 30 ml of Rosneft flushing oil. At first, everything was very coked and the engine went into overdrive and only ran on 80 gasoline. I started adding flushing oil to 80-grade gasoline, and somehow it cleared up and switched to 92-grade. It seems like you don’t have to pour the rinse anymore, but out of habit I pour it, but it won’t run out. Oil for two-stroke engines, which I don’t pour into a chainsaw in a ratio of 1:50, is more expensive. And with it, on 80 liter gasoline, it also went into overdrive, but I don’t want to experiment anymore after cleaning it. It works - and it's great.
please tell me. I have a MF-70 walk-behind tractor but there is no ignition, what can I install or remake?
Sanjok wrote: Yesterday I was mowing my MF and after 30 minutes of work the connecting rod jammed on the crankshaft. I added XADO 2 T oil to gasoline in the ratio of 30 grams of oil per 1 liter of gasoline. I think the reason is the oil, since until this year it ran on regular diesel oil. Who can tell me something about this.
Sanjok, Lew in a ratio of 1:40, gasoline 92 and semi-blue oil or mineral water from the leftovers. For 4 liters of gasoline, 100 ml of oil, + 30 ml of Rosneft flushing oil. At first, everything was very coked and the engine went into overdrive and only ran on 80 gasoline. I started adding flushing oil to 80-grade gasoline, and somehow it cleared up and switched to 92-grade. It seems like you don’t have to pour the rinse anymore, but out of habit I pour it, but it won’t run out. Oil for two-stroke engines, which I don’t pour into a chainsaw in a ratio of 1:50, is more expensive. And with it, on 80 liter gasoline, it also went into overdrive, but I don’t want to experiment anymore after cleaning it. It works - and it's great.