Chainsaws Lesnik: advantages of the tool, review of the model range

Gasoline chain saws Lesnik appeared on sale not so long ago, but are already in demand due to their good price-quality ratio. As part of the article, we will consider the most popular models from the entire model range, their advantages and disadvantages, compare them with similar chainsaws and back it all up with real reviews from owners.

Advantages and features of Lesnik chainsaws

1. The specific geometry of the body in the form of a drop allows you to carry out work in hard-to-reach places and in difficult areas;
2. Reliable and high-quality gasoline internal combustion engines with high performance;
3. Thoughtful alignment and verified balance of the chainsaw;
4. Easy and intuitive controls;
5. Oregon brand chains and tires, considered the most durable and durable;
6. Multifunctionality;
7. Long service life;
8. Low wholesale and retail cost.

The distinctive features of Lesnik chainsaws are compactness and light weight, mobility and high performance. Even the cheapest chainsaw can work without a break for 2-4 hours, which is quite enough for putting things in order in the garden or country house, as well as for carrying out minor repairs and construction work around the house. In addition to versatility and reliability, consumers are attracted by the cost of Lesnik gasoline saws, which puts this tool in the TOP of the most popular and in demand in this segment.

User manual

Each carburetor owner must have the necessary tools to adjust this system. There are three adjustment screws that are located on the body of the device. They have their own markings:

• L - screw for correcting low speeds.
• H - screw for adjusting high speed.
• T - regulates idle speed, in most cases used for experiments.

Chainsaw air filter

Before adjusting the carburetor, you need to prepare the device:

1. The engine warms up, that is, it starts about 10 minutes before repairs, and turns off when starting work (see how to start a chainsaw).
2. The air filter is checked and washed.
3. The chain is stopped by turning screw T until it stops (see chain oil).

To carry out a safe repair, you need to prepare a flat surface where you can carefully place the device and turn the chain in the opposite direction. Need a tachometer. It determines whether there is a malfunction in the carburetor. When turning the screws, the sound should be perfect and absolutely smooth. If you notice squealing notes, the mixture is oversaturated.

Carburetor adjustment is divided into two main stages. The first one is called basic. It is performed with the engine running. The second is performed when the engine is warm.

To carry out the carburetor setup procedure successfully, you need to read the operating instructions for a specific model in advance to identify additional features of setting up the device.

To correctly configure the carburetor of a Chinese chainsaw, you must first remember the factory settings of the device, then turn on the engine. Subsequently, you will have to leave it running for several hours in order to accurately set your own parameters. Sometimes work is carried out only after ten minutes of engine operation, but many Chinese-made models require special handling.

Chinese chainsaw model

Adjustment procedure:

1. Activities begin in idle mode. Using the adjusting screws, you need to achieve a systematic increase in engine speed, so you should first let it run at low speeds. A deviation from the norm is the movement of the chain along the bus. In this case, you need to adjust the outer screws to the optimal position so that the chain remains motionless.
2. The transition to medium speed speed is carried out. Sometimes the engine starts to smoke. This defect can be eliminated by tightening the screw to supply a leaner fuel mixture.

In this case, the smoke will disappear, but the engine speed will increase. You need to adjust the settings until you reach a level where, when you press the throttle, the engine smoothly picks up speed, and no sudden jerks or interruptions are heard.

• The device's engine is being checked. The chainsaw is switched to minimum speed, and then the lever is quickly pressed. When pressed maximally, it is held for 3 seconds. If there are problems with the engine, you need to gradually loosen the screw until the optimal position is reached.
• The chainsaw should work for several hours in real conditions. You need to cut wood, and then inspect all the elements involved in this event. If there are deviations, they must be corrected using adjusting devices. When all defects have been eliminated and the optimal settings have been established to supply correctly concentrated fuel, the device setup process can be considered complete.

Read:

Before using the tool, be sure to read the operating instructions for the Lesnik 3816 chainsaw. It contains important points, such as:

• preparation for launch;
• recommended oils for lubrication and preparation of fuel;
• the process of preparing the fuel mixture and the required proportions are described in detail;
• issues of safe operation;
• storing a chainsaw in winter;
• trouble-shooting.

Currently reading: Chainsaw “Ural”: structure, advantages and disadvantages, technical characteristics

Forester 3816 is a Chinese chainsaw and breakdowns with it occur much more often than with saws from Efco, Oleo-Mac, Stihl, so the section of the instructions dedicated to troubleshooting and troubleshooting will come in very handy.

The following signs and malfunctions indicate the need to adjust the carburetor:

• the engine starts with effort and stalls almost instantly;
• gasoline consumption is excessively high, the exhaust is too thick, the combustible mixture in the cylinder does not burn completely;
• the factory settings of the chainsaw carburetor are lost (due to vibrations or unsuccessful attempts at adjustment);
• malfunctions of the air purification system, which led to the entry of debris into the fuel mixture distributing mechanism;
• significant wear of the piston group - carburetor adjustment in this case acts as a temporary measure.

It is clear that if dirt gets into the fuel system, one adjustment alone will not solve the problem - it needs to be flushed. If the piston is worn out, a major overhaul is required. However, in all these cases, the carburetor is also adjusted.

Almost any Chinese chainsaw has the same adjustments as its branded counterparts. The same screws L, H and T are present. Sometimes there are saws in which only the idle speed can be adjusted. However, according to reviews from owners and service workers, not every chainsaw can be adjusted without problems. Even for experienced repairmen, some models can take a decent amount of time before getting an acceptable result.

The standard position for “Chinese” carburetors is the position of the screw L, at which it is loosened by one and a half turns from the fully clamped position. For screw H - one revolution from the same state. In many videos, screw L is called adjusting the quality of the mixture, and screw H is its quantity. The idle speed is adjusted in the same way as described above on a warm engine.

Related Posts

Review of popular models

There is a basic configuration for each model of Lesnik saws. The basic kit is:

1. Tire and chain;
2. Candle key;
3. User manual;
4. Warranty card;
5. Measuring cup for mixing oil and gasoline;
6. For some brands, the company adds protective gloves and goggles to the basic kit.

Chainsaw Lesnik 2512

The compact petrol saw Lesnik 2512, designed for household and semi-professional work, can be operated with one hand.

Advantages and characteristics:

1. Two-stroke internal combustion engine with a power of 0.95 kW (1.2 hp) and a volume of 25 cm3;
2. Vibration protection system, shoulder strap for carrying tools;
3. Easy starting in cold weather and simple controls;
4. Weight – 2.9 kg;
5. Tanks for gasoline and oil - 200 ml each;
6. Chain pitch - 3/8;
7. Chain thickness - 1.3 mm;
8. Warranty period – 1 year;
9. Bar 30 cm or 12 inches long, 44 links per chain.

Flaws:

1. In winter it does not always start quickly;
2. Plugs and ignition coils quickly fail;
3. The need for constant chain tension.

Chainsaw Lesnik 3816

Well-balanced hand-held chainsaw Lesnik 3816. Designed for work in the garden, on the site and for carrying out minor repair and construction work.

Advantages and characteristics:

1. Two-stroke internal combustion engine with a power of 1.4 kW (2.0 hp) and a volume of 38 cm3;
2. Easy starting in cold weather and simple control, starting spring, screw tension of the cutting chain;
3. Balanced body and ergonomic design;
4. Weight – 4.9 kg;
5. Tanks for gasoline (310 ml) and oil (210 ml);
6. Chain pitch - 3/8;
7. Chain thickness - 1.3 mm, bar and chain lubrication - automatic;
8. Warranty period – 1 year;
9. Bar 40 cm or 16 inches long, 57 links per chain.

Flaws:

1. The engine is difficult to start and often stalls;
2. The candle is filled with gasoline;
3. Chain lube may leak during storage;
4. The carburetor has to be adjusted frequently.

Chainsaw Lesnik 4518

The universal gasoline saw Lesnik 4518 is capable of sawing large trunks and industrial forests.

Advantages and characteristics:

1. Two-stroke internal combustion engine with a power of 2.13 kW (2.9 hp) and a volume of 45 cm3;
2. Easy starting in cold weather and simple controls, starting spring, screw-type, tool-free tensioning of the cutting chain;
3. Ergonomics, vibration protection system;
4. Weight – 6.5 kg;
5. Tanks for gasoline (550 ml) and oil (260 ml);
6. Chain pitch - 0.325;
7. Chain thickness - 1.5 mm, bar and chain lubrication - automatic, oil pump adjustment;
8. Warranty period – 1 year;
9. Bar 45 cm or 18 inches long, 72 links per chain;
10. Electronic ignition;
11. Nylon air filter;
12. Three-cam clutch;
13. Additional equipment - gear stop.

Flaws:

1. Inconvenient tension system for the user;
2. After long-term storage, the internal combustion engine is difficult to start.

Chainsaw Lesnik 5220

The powerful chainsaw Lesnik 5220 cuts logs of any diameter and is convenient for construction work. The correct balance is the absence of vibration and minimizing the load on the operator.

Advantages and characteristics of the Lesnik 5220 chain saw:

1. Two-stroke internal combustion engine with a power of 2.5 kW (3.4 hp) and a volume of 52 cm3;
2. Easy starting in cold weather and simple controls, spring start of the internal combustion engine, screw chain tension;
3. Vibration protection system;
4. Balanced body and ergonomic design;
5. Weight – 8.5 kg;
6. Air filter with easily removable bolt-on cover;
7. Start blocking;
8. Tanks for gasoline (550 ml) and oil (260 ml);
9. Chain pitch - 0.325;
10. Chain thickness - 1.5 mm, bar and chain lubrication - automatic, oil pump adjustment;
11. Warranty period – 1 year;
12. Bar 50 cm or 20 inches long, 76 links per chain.

Among the disadvantages, it is worth noting possible malfunctions of the oil pump. Many users, and even sales assistants in stores, require the use of branded oils, for example from the Patriot Garden line.

Basic configuration of chain saws “Lesnik”

Each chain saw of the Russian company “Lesnik” is supplied in a certain configuration and in disassembled form. By purchasing a saw, you get:

• guide bar and saw chain;
• spark plug wrench for saw maintenance;
• technical documentation (warranty card and operating instructions);
• special measuring container for mixing fuel.

Optionally, with some models, the manufacturer can supply additional accessories in the form of protective gloves and glasses. The company has the right to change the package for the availability of accessories.

The main office of the Lesnik company is located in the Russian Federation. To reduce the cost of the finished product, production was moved to China, which significantly reduced the cost of finished saw tools, but did not affect their quality.

Possible malfunctions and repairs

Most often, as practice has shown, the following problems arise:

1. Starter failure;
2. Failure in the lubrication system;
3. Poor operation of the chain brake;
4. Rapid chain wear.

Video on how to troubleshoot the most common problems with the Lesnik 3816 chainsaw

Video with recommendations for care, assembly and adjustment of the Lesnik chainsaw:

Carburetor adjustment

Before adjusting the carburetor, it is necessary to clean the air intake filter and warm up the engine. In this case, the carburetor jets must be clean, and there should be no water in the float chamber. The adjustment is carried out with a special key (included) - rotate the fuel quality and quantity screws, as well as the idle screw.

How to adjust the carburetor of a Lesnik chainsaw - video:

Final check at idle

Problems with the bar and chain can occur almost immediately after purchase. It is recommended to replace with high-quality ones from OREGON. If the tire does not last for the first time, it is better to throw out the chain immediately. According to numerous user reviews, it stretches like plasticine.

Engine malfunctions are very rare and in most cases are due to wear and tear or manufacturing defects. But problems with the carburetor are not uncommon.

To diagnose carburetor breakdowns, it is better to use the operating instructions; it describes all possible faults and how to eliminate them. Upon completion of the repair, the carburetor will need to be adjusted. This is not so easy to do. Our article on setting up or the same operating instructions for the Lesnik 3816 chainsaw will help with this.

It is impossible to say definitively that any of the listed chainsaws are definitely better than Lesnik 3816. Each tool has its pros and cons. There are successful examples of using specific saws for several years, and there are also unsuccessful chainsaws that cause a lot of problems from the first day.

Need to do a little research. Acceleration of the device is initiated. It is necessary to evaluate the proper operation of the engine during maximum speed. When the engine is functioning correctly, it means that when you press the accelerator, the speed quickly increases to 15,000 rpm.

If this does not happen or the increase in speed is too slow, you must use the screw marked L. It turns counterclockwise. Moderate movements must be observed, since the turn cannot be more than 1/8 of a full circle.

Before this procedure, it is necessary to carry out a full adjustment of the carburetor components when operating at maximum speed. Next, you should check the functioning of the device in idle cold mode. When the correct adjustment parameters are achieved, you will notice that the carburetor design closely matches the following criteria:

1. When the idle cold mode is activated, the chain does not move.

1. When the accelerator is pressed even slightly, the engine accelerates at an accelerated pace. With gradual deepening of pressure, you can notice that the engine speed increases proportionately, reaching the maximum permissible values.
2. When the engine is running, you can compare its sound to a four-stroke device.

If violations are noticed in the given parameters or the device has not been fully adjusted, you need to perform the main setup step again. Sometimes actions are performed incorrectly. In this case, the device may fail due to the loss of the correct node settings. In this case, you will have to contact a specialist.

The design of different carburetor models is almost the same, so when working with them you can use the standard scheme. All elements must be removed carefully and then laid out in the order given below so that you can successfully place the items in place after the completion of the repair work.

Removing the Top Cover

1. The top cover is removed. To do this, you need to unscrew the 3 bolts holding it in a circle.
2. The foam rubber is also removed, since it is the upper component of the filter that conducts air.
3. The fuel hose is removed.
4. The drive thrust is output directly to it.
5. The cable end is disconnected.
6. The gasoline hose can be completely removed if you systematically pull it off the fitting.

Competitive chainsaw models

The Russian chainsaw market is represented by a wide range of models of foreign and domestic chainsaws from other manufacturers. Below are the TOP 5 chainsaws, which in some respects can compete with the Lesnik brand and their technical characteristics:

1. Caliber BP-2600/18U can cut logs with a diameter of 400 mm. Two-stroke internal combustion engine with a power of 3.5 hp, 18-inch tire, weight - 6.2 kg. Modern design and convenient settings, long-term battery life, primer, diaphragm carburetor, lubrication system and emergency brake. When compared with the Lesnik 5220 chainsaw, the Caliber’s performance is lower;
2. Huter BS-45M made in Germany is produced for small farms. Two-stroke internal combustion engine with a power of 2.3 hp. and a volume of 45 cm3 allows you to perform any work in the country, in the garden or on the site. Tire length – 16 inches, oil pump with automatic lubricant supply. Less convenient to operate and maintain than Lesnik 3816;

3. CARVER PROMO PSG-45-15 is intended for gardening, pruning branches and bushes, dead wood, collecting firewood and construction work. A two-stroke internal combustion engine with a power of 2.4 hp, a 15-inch tire, compactness and low weight allow you to work at heights and in hard-to-reach places. Chainsaws Lesnik 3816 and Lesnik 4518 with similar characteristics are more reliable and durable;
4. The Soyuz PTS-99371 saw is equipped with a 2.7 hp engine. and volume 38 cm3. Model weight – 5.1 kg, tire length – 18 inches, automatic lubrication system and inertial chain brake. A similar chainsaw, Lesnik 4518, has a wider range of functionality and safety mechanisms;
   Read also:  We make attachments for walk-behind tractors with our own hands, photos and drawings
5. The compact chainsaw DDE CS2512 weighing 3.15 kg can serve summer cottages, gardens, and work on minor repair work. The engine has a power of 1.2 hp. With such a low weight, the chainsaw is convenient for performing high-altitude work. Compared to the Lesnik 2512 chainsaw, it is heavier and more inconvenient to use.

When choosing a chainsaw, there is only one rule: the chainsaw must be reliable and safe, so Lesnik undoubtedly deserves more attention, even if chainsaws are inferior in some respects to competing models.

How to choose

Have you already assessed the quality of Lesnik brand chainsaws?

Qualitatively Mediocre

Today, the market offers household and professional models. They may not handle extreme cold conditions, but are great for commercial use on a daily basis. That is, they can be used in construction or logging before the onset of severe cold weather.

You need to choose based on your current needs. This will allow you to understand whether you need to buy a professional chainsaw or you can get by with a household one. Regardless of the choice, the devices are quite compact and easy to disassemble.

It is necessary to carefully monitor the condition of the tool so that it does not break. To do this, you need to follow the instructions. If problems arise during warranty service, do not repair it yourself. It is better to turn to professionals to do the work using original parts.

Reviews

Here are a few reviews left by visitors to our site:

The low performance of the Lesnik 2512 gasoline saw is compensated by its compactness and low vibration, there are no problems with starting in winter, and the cost of servicing the tool is minimal. Over three years of operation, I replaced two chains and a drive sprocket.

Andrey

The Lesnik 3816 engine starts without problems, you can cut a log with a diameter of up to 30 cm in one go. It is difficult to work felling trees in winter - it is very difficult to saw raw and frozen wood, but for housework there is more than enough engine power.

Vladimir

Information support

The operating instructions included in the factory kit contain information on preparing the saw for startup, maintenance, and the use of alternative motor and chain oils.
We also offer time-tested algorithms for searching for causes of failures typical for chainsaw equipment and ways to eliminate them. Using the recommendations given, the saw owner can, if necessary:

• replace the parts of the sawing device yourself;
• adjust the engine carburetor for maximum efficiency and performance;
• Using the spare parts available in the repair assortment, perform routine repairs of the chainsaw without involving service providers.

Maximum number of revolutions

To limit this indicator, you need to use a screw marked H. To increase the number of revolutions, turn it clockwise, and to reduce them in the opposite direction. The maximum frequency should not exceed 15000 rpm.

If you make this figure larger, the device’s engine will wear out, which will lead to problems in the ignition system. When rotating this screw, you need to take into account the ignition processes of the device. If the slightest malfunctions appear, then the maximum speed value must be reduced.

A little about the manufacturer

For many years, this Russian company has been producing electrical equipment for construction and gardening. The unsurpassed quality of this manufacturer’s products has been confirmed by massive inspections by specialists from different countries. Undoubtedly, the equipment meets all the necessary standards, both safety and quality (see rating of chainsaws for reliability).

Every year the manufacturer produces thousands of models of its products , the main of which are chainsaws made exclusively from high-quality material and using specially created technologies. This is precisely the reason for such massive popularity of the company’s products among consumers from different parts of the world.

TBP-4500

Another chainsaw that is sold under the Taiga brand is TBP-4500.

There is no particular difference with the previous model. The main difference is the motor power, which is 500 W more. Also, as standard, the saw comes with another saw set, which has a chain pitch of 0.325.

Due to a little more power and a different chain, the TBP-4500 is easier to cut through thick trees, but the difference is not particularly noticeable.

Externally, it is almost impossible to distinguish the TBP-4000 and TBP-4500 models, because they have the same dimensions, color, body details. Also, if necessary, you can install a piston group on one chainsaw from another, thereby adding or reducing power.

The video below shows the unpacking of the Taiga TBP - 4500 chainsaw. Equipment, assembly of the new saw and preparation for work. At the same time, the operator talks about the purpose and characteristics of the model.

Criterias of choice

When assessing the characteristics of a purchased chainsaw, it is recommended to take into account the conditions of its future operation.

• Small-capacity, lightweight and easy-to-drive models complete the technical base of forestry and gardening farms. Lesnik saws are included in the standard equipment of scientific expeditions, large tourist groups and emergency rescue organizations.
• Models in the mid-power range can be used for felling dead wood and other sawing operations of increased complexity. The performance of Lesnik chainsaws is ensured by the stable traction characteristics of standard power units and the high quality of saw components.

The feasibility of using branded gas and electric saw equipment is confirmed by friendly reviews from owners from various regions of the country.

Main advantages

Each manufacturer has its own strengths, the Lesnik brand is no exception.
Here's what's worth noting when working with these chainsaws:

• The unusual appearance (drop-shaped) allows you to perform work even in some hard-to-reach places.
• High-quality gasoline engines with a high level of performance are used.
• Good balancing of the product.
• Chains and tires are used by Oregon.

• Multifunctionality of some devices.
• Easy to use, no need to spend a lot of time figuring out how the tool works.
• Long period of operation.
• Reasonable price.

Expert opinion Dmitry Konstantinovich Levin

It is the price that often plays a decisive role for users when choosing a chainsaw. The Lesnik brand allows you to get everything you need without overpaying for the name. It appeared recently, so the manufacturer has not yet made a premium for it.

All models are quite small. At the same time, the cheapest model can work stably without interruption for up to 3 hours, which is an important competitive advantage. Almost all household chainsaws need a break every 15 to 20 minutes. Now it’s worth considering the leading devices that are used today in the domestic market.

Analogs

Household chainsaws of the household class, identical in power and cost, are presented in the chainsaw equipment market with a large selection. Models from European and Asian brands CHAMPION 237-16, Huter BS-45M, Partner P340S-14, MTD GCS 3800/35 and Shtil 180 chainsaw are in consistently high demand.

Application

Chainsaw Lesnik 3816 belongs to the household class and is intended to perform simple tasks, such as:

• procurement of firewood in small quantities;
• tree processing;
• performing simple tasks during construction;
• cutting down dead wood.

Of course, the tool is not suitable for carving, but for all the tasks listed above, it will become an indispensable tool.

First stage

Each model of chainsaws comes with instructions for use, which indicate all the rules for maintenance, repair, setting up the saw, as well as basic safety rules. Before you start working with the tool, you must study the manual and use it if you encounter any difficulties using the chainsaw.

If any breakdowns are detected, you can independently inspect the equipment if you have been dealing with chainsaws for a long time. If your experience is not enough to provide quality assistance and repairs, then it is recommended to contact a service center, where experienced specialists will provide qualified technical service.

Judging by many reviews, there are no particular problems in using Lesnik chainsaws. In some comments, owners point to the need to adjust the carburetor, as well as rapid wear of the bar and chain. In many reviews you can also find a recommendation to replace the drive bar and chain with products from more popular companies.

The adjusting screws for the highest and lowest speeds should be moved clockwise until the highest resistance is met. When the screws reach the stop, you need to move them in the opposite direction and leave them 1.5 turns.