Application specifics
Forza walk-behind tractors are manufactured by a well-known domestic company in Perm. The production of this agricultural machinery began back in 2010. During this time, the manufacturer has established its walk-behind tractors as a high-quality and worthy product, which is known even outside of Russia.
The manufacturer Forza produces a wide range of walk-behind tractors for every taste. These are both diesel and petrol models. The model range is represented by walk-behind tractors from 75 to 125 kg, with power from 6.5 to 15 horsepower. This allows the units to be used both in a small summer cottage and in a large agricultural area.
A wide range of walk-behind tractors is produced by the manufacturer Forza
Depending on the model, Forza walk-behind tractors can be used for:
- preparing the soil for sowing;
- loosening and hilling;
- weeding;
- harrowing;
- soil transportation;
- grass cutting;
- snow removal;
- compacting the soil.
Advantages and disadvantages of the unit
Forza walk-behind tractors have the following advantages:
- high quality;
- products are certified;
- affordable price;
- It is possible to install attachments.
Owners consider the rapid wear of cutters to be a disadvantage of the Forza equipment.
Many owners consider the disadvantages of the Forza equipment to be the rapid wear of cutters, as well as inefficient gas consumption. Some owners are not satisfied with the excessive vibration of the walk-behind tractor after starting the engine, but it is no different from the vibration of models from other manufacturers.
Gearbox
On walk-behind tractors you can find gearboxes such as:
- chain;
- gear;
- gear-chain.
Additional information - on walk-behind tractors of previous years of production, gearboxes were installed, consisting of a worm mechanism and a gear. This design was distinguished by a high efficiency, but could not withstand high loads. For example, even working with a hiller or a light plow caused the gearbox mechanism to overheat and fail. Currently, walk-behind tractors with a worm gear are almost never found.
Chain reducer. The chain gearbox is a reliable and at the same time simple design consisting of a chain and a set of gears. It is used in light and medium-sized walk-behind tractors with small and medium-power engines. Easy to maintain, easy to repair.
IMPORTANT! Over time, the chain can stretch and must be replaced promptly. If the gearbox housing is non-separable, then the entire assembly is replaced.
Gear reducer. The gear reducer is considered the most reliable and unpretentious in operation. It is capable of working on any soil, and in the most extreme conditions. Gear reducers are installed on heavy walk-behind tractors with a PTO operating with heavy attachments. The gearbox is practically eternal, the main thing is to change the oil on time.
One of the main disadvantages of gear reducers is the high noise level and its cost.
Gear-chain reducer. The most common gearbox. The gear-chain reducer is found only on domestically produced walk-behind tractors. Available in single-speed, two-speed and more. The design provides high elasticity during operation (ideal output shaft speed is 80-120) and is characterized by a low level of vibration. Very high service life and reliability of the gearbox. Structurally, it is the most complex and cannot withstand heavy loads. The development of this gearbox was caused by the need to increase the number of front gears (up to
IMPORTANT! The main disadvantage of this gearbox is the need for maintenance in strict accordance with the requirements of the manufacturer. Violation of them is fraught with breakdown of gearbox parts (break or stretching of the chain, breakage of gears) followed by expensive repairs.
Model specifications
Below we will present the general technical characteristics of the models. This will allow you to quickly familiarize yourself with the manufacturer’s available model range and choose the one that is most suitable for you. The gearbox design of Forza walk-behind tractors is common to all models.
Dimensions and weight of the structure
The dimensions and weight of Forza equipment depend on the specific model. The heavier the weight of the unit, the more powerful the model itself is, and the more complex the functions it can perform. Manufacturers have tried to make the dimensions of each model compact so that such equipment can be conveniently operated alone. The weight of the structures can reach 125 kg, which allows them to be used on areas of up to 1 hectare and called semi-professional models.
Modification and engines
In the process of manufacturing walk-behind tractors, manufacturers use different engines (ranging from economical Chinese ones to high-quality well-known brands “Briggs & Stratton” and “Subaru-Robin”. Their power varies from 6.5 to 15 hp. It is this variety of units that allows you to choose the most suitable for each buyer, depending on the amount and complexity of soil treatment, the cost of the model itself and the frequency of its use.The engines of the Forza models are four-stroke single-cylinder air-cooled.
Manufacturers use different engines in the manufacturing process of walk-behind tractors.
Fuel consumption
Fuel consumption of Forza walk-behind tractors depends on the complexity and duration of the work performed, as well as the model of the unit itself. In comparison with models of such equipment from other manufacturers, Forza walk-behind tractors can be called economical in fuel consumption.
Average fuel consumption of Forza walk-behind tractors:
- models with power up to 6.5 hp – 1.4 liters/hour;
- up to 8 hp – 2.3 liters/hour;
- up to 10 hp – 2.8 liters/hour;
- up to 13 hp – 3.3 liters/hour;
- up to 15 hp – 3.7 liters/hour.
Complete set of walk-behind tractors
Each Forza walk-behind tractor comes with the following standard equipment:
- wheels;
- collapsible cutters;
- fasteners;
- instructions for the motor;
- instructions for the walk-behind tractor;
- removable handle and protective wings.
The fuel consumption of Forza walk-behind tractors depends on the complexity and duration of the work performed.
Attachments
Depending on the model, anyone can purchase attachments for the Forza walk-behind tractor for an additional fee.
It can be:
- front and rear adapters;
- trailers;
- potato diggers;
- mowers;
- hillers;
- shovels for clearing snow.
With the help of attachments, a walk-behind tractor can become a full-fledged machine for solving many agricultural problems.
Presented model range: description and cost
Below will be presented the model range of Forza walk-behind tractors with a detailed description. In addition to the technical characteristics, the price indicated is for the unit excluding attachments.
The Forza walk-behind tractors of the FZ series are designed for use on land plots of up to 1 hectare, therefore they are represented by models of medium and low power. The “MB” series refers to gasoline walk-behind tractors with a power take-off shaft.
A walk-behind tractor can become a full-fledged machine with the help of attachments
FZ-01-6.5 F
A high-quality unit with an engine power of 6.5 hp. and manual starter. The Forza 6.5 walk-behind tractor is a basic model with pneumatic wheels, a belt clutch and a chain drive. The instructions clearly indicate the recommended power for long-term operation of the walk-behind tractor, depending on the size of the area being treated. The fuel tank capacity is 3.6 liters. The width of the soil treatment is up to 120 mm, the depth is 30 cm. For operation, the model has four speeds - 2 backward and 2 forward. The weight of the unit is 100 kg. The price of the model is 33,000 rubles.
FZ-01-8.0 F
Compared to the previous model, FZ-01-8.0 F is considered a more powerful model. It can be classified as a heavy walk-behind tractor, since it has the ability to independently install an engine with a power of 15 hp on its frame. The compact unit has 2 forward and 2 reverse gears, as well as an 8 hp engine from the manufacturer. The weight of the equipment is 110 kg, the fuel tank volume is increased by 6.4 liters. The cost of the model is 35,000 rubles.
FZ-01-9.0 FE
The medium-heavy model has 9 horsepower. The 4-stroke gasoline engine ensures high-quality operation of the unit. The model is equipped with two high-quality wide pneumatic wheels, thanks to which you can hill up and loosen even difficult soils. The cultivation width is 120 cm and the depth is 30 cm. The weight of the model is 115 kg. Price of the Forza walk-behind tractor for 9 hp. is 37,000 rubles.
Motoblock FZ-01-9.0 FE
Forza MB-80
This model is the base model in the Forza MB series. This is an amateur series, which is intended for private use on soil up to 1 hectare. The compact and economical model has 3 gear speeds. The Forza MB 80 walk-behind tractor has a push-button motor stop for worker safety.
Main technical characteristics:
- manual start;
- weight - 80 kg;
- power 6.5 hp;
- fuel tank 3.6 liters.
The cost is 24,000 rubles.
Forza MB-105/7.0
The Forza walk-behind tractor with 7 horsepower has a manual starter and a gearbox. The maximum tillage width of the Forza MB-105 walk-behind tractor is 105 cm, and the width is 30 cm. The weight of the model reaches 121 kg. There are 2 forward and 1 reverse speeds. Wheel size – 4X10. The minimum price for this model is 35,000 rubles.
Motoblock Forza MB-105/7.0
FZ 177 FD
The FZ 177 FD is a 4-stroke, single-cylinder, air-cooled engine. The engine capacity is 270 cmᶾ. The 9 horsepower engine allows you to perform work on medium-difficult soil. The engine on this unit can be started using a manual or electric starter. Fuel consumption per hour ranges from 2.5 to 3 liters. Price – 15,000 rubles.
FZ-02-6.5F
The engine power of this model is 6.5 hp. Four speeds allow full operation of the unit. The fuel tank has a volume of 3.6 liters, the weight of the equipment is 100 kg. Model with electric start and V-belt clutch type. Price – 35,000 rubles.
Forza walk-behind tractor.
Who can say what kind of animal this is?
this is MB-1 under a different name" >
I bought one for myself with wheels from an ATV. While I’m cultivating with crow’s feet. I plan to buy a PON-B-02 plow from Neva. So far I’m happy with the unit
MB Kalina and MB Granda will appear soon.
Motoblock "FORZA" place of production: Perm. Analog gearbox - “CASCADE”. Assembled from DSE (parts, assembly units) produced in China. Screwdriver production 10 thousand pieces per year. It is equipped with various engines from 6 hp. up to 15. Complaints occur 2-5 per thousand. Under the same brand, chain saws, trimmers, mowers, wheelbarrows and other consumer goods.
ali_kъ wrote: Motoblock “FORZA” place of production: Perm. Analogue gearbox - “CASCADE”
Please tell me, is the gearbox like the MB-1? Otherwise, in the description there is something about a comfortable gear knob, so I’m wondering where it comes from.
Reducer MB-2, with ball bearings and seals on the output shaft. The gears are engaged with a lever, not a pimp.
The arrow indicated the lever, switching left-right, neutral in the middle. A very convenient gadget: fixed forward gear.
. overall: it turned out to be a rare *****. asterisks mean: very bad words and a lot))))
ali_kъ And what are the goosenecks for this unit? And aren't they sold separately? Or tell me where they are.
-=Suvorovets=- Two rubber tracks. On a frame-frame. Of the ten such products sold, eight have already been returned. Due to the fact that the structure collapsed. They are made somewhere in Izhevsk.
Hello, dear forum users! I’m concerned about purchasing a walk-behind tractor, I want to get some advice. I chose from Neva (Subaru, Briggs, Honda), Oka (Lifan 6.5), Tselina (Lifan 6.5), Salyut (Lifan 6.5). Result: Neva is in the city, the price is the cheapest
37-38tyr, Oka - 27, Tselina from 26 without cutters (naked), no fireworks at all, only order via the Internet. Again, on the Neva, Oka, Tselina, there seems to be a service, but as they say the exchange service takes from 20 to 45 days, mostly for engines everything is made to order, there are mechanics (cables, springs, but not everything). The prices for Salute on the internet are interesting (
from 21tr), but all spare parts are on order. I also came across our production, the Forza FZ-01-6.5F walk-behind tractor. Their website was already here on the forum. I went, talked, looked. In general, like everywhere else. Engine Lifan, or our branded Forza. The difference is in color and sticker. Still the same Lifan, only a special order. This is where the constructor is assembled. I can’t say anything bad about the build quality, I looked at the Neva, Oka, absolutely the same thing. The kit and consumables (belts, filters, attachments) are all interchangeable. Reducer - double chain. Forza has a reinforced gearbox, the axles have bearings, as they said, from Niva. They sell more than 500 pieces per season, there are almost no defects. The most important thing is the price, with a 6.5L Lifan (Forza) engine, including a milling cutter - 22,500 rubles, yes, everything attached is our own production, and many of our own designs, if, they say, you need it, bring the drawings, we’ll make a special order, just pay. The question is, does anyone have such a device? How is he at work? And what do you recommend that you take from the implements that you need right away (I can probably cook some of it myself - make it), your house, 20 acres of land. Apart from the Champion snowfield and the car, I did not work with any other equipment (MB). Sorry for the confusion, my brain is already broken, I want it as always, cheap, good, and service close at hand. With all due respect to you!
PS. There is also the same one, only with wheels from an ATV, but I don’t know if a walk-behind tractor needs such wheels, what do you think? [
User manual
The advantage of Forza models over walk-behind tractors from other manufacturers is that they come with high-quality detailed specifications. With the help of such instructions, even a beginner can use the walk-behind tractor correctly and easily.
Use high quality fuel and oil to operate the walk-behind tractor.
Service
To ensure that your purchased walk-behind tractor is as durable as possible, be sure to read the instructions before starting to operate the equipment. When starting work, take into account the type and complexity of the soil and do not work for a long time at maximum power. Be sure to clear the area of debris, branches and large rocks. When working with equipment for a long time, provide it with a rest every 3-4 hours for 15-20 minutes. This will protect it from overheating. Be sure to break in the walk-behind tractor before starting work.
Run-in
For high-quality and durable operation, the device is run-in, both on a newly purchased model and on a unit that has been idle for a long time. Run-in is always done only at medium speeds. A prerequisite is to turn off the unit every 1.5-2 hours.
The run-in of the walk-behind tractor itself lasts for a total of 8-10 hours, after which you can begin to operate the equipment at high power.
Motoblock Forza 9 l. With. – a reliable unit of the highest quality!
Motoblocks have become a real salvation for many farmers, rural residents and summer residents. After all, it has become so much easier and faster to do hard and tedious work in the garden and on your plots. It is their versatility, power and price that these units have won over many owners.
It's no secret that the better the equipment of a walk-behind tractor, the longer it will last. Today we will talk about such high-quality Forza units with a capacity of 9 horsepower. Let's find out all the advantages, get acquainted with the detailed characteristics and other nuances of this model.
Basic faults
The main malfunctions of Forza walk-behind tractors that the owner of the equipment may encounter:
- Unit overheating. May be associated with operating the device at maximum power continuously for more than 2 hours. Overheating can also be caused by insufficient engine oil.
- The equipment does not turn on. In such a situation, we advise you to look at the spark plug, change the fuel and clean the fuel filter.
Be sure to use high quality fuel and oil as this will extend the life of the equipment. During storage, thoroughly clean the walk-behind tractor from dirt, and also make sure that it does not stand for a long time in direct sunlight.
Increasing speed with your own hands
How to make your walk-behind tractor faster? It should be noted that we are talking about transport speed. The Neva MB-2 walk-behind tractor, with certain modifications, can reach speeds of more than 20 km/h, however, if it does not have a differential, then control becomes significantly more complicated.
You can increase the speed in several ways, for example, install wheels of larger diameter or change the gear pair of the wheel reducer, replacing the standard gears with 61 and 12 teeth with 55 and 18 teeth, respectively. This method is quite complicated to implement, but it allows you to increase the initial speed by almost 2 times.
Some owners want the walk-behind tractor to travel at a speed of 40 km/h. It is possible to make such a modification, but it must be taken into account that it will place a large load on the gearbox, and it will be difficult to drive such a vehicle.
What techniques did you use to change the speed on a walk-behind tractor?
