Chainsaw Poulan 2150; useful tool for home use

Technical characteristics and parameters

The saw's autonomy is ensured by a standard two-stroke carburetor engine with a displacement of 36 cm3, developing a power of 1.8 hp at 13,000 rpm.

• The power unit runs on a mixture of motor gasoline and oil for two-stroke internal combustion engines in a combination of 25:1. Fuel is taken from a built-in fuel tank with a volume of 350 ml.
• The combination of a wear-resistant coating on the inner diameter of the cylinder and a low coefficient of friction of the piston group material allows the use of the engine's traction capabilities with minimal power losses.
• The electronic ignition system ensures complete spark generation and guarantees reliable engine starting at low temperatures, stable operation at idle and operating modes.

Reviews and prices

Dmitry, Mozhga: “I work in the forest. I don’t have a professional saw yet, I work in Poulana. The unit is good, convenient, easy to start. Even in hot weather it can work for a long time without stopping.”

Fedor, Kanash: “I have had a Poulan saw for about 5 years. I work with it a lot. The plastic is good, the parts of the internal systems are reliable. I'm happy with the device."

Alexander, Ufa: “I’ve been using a Poulan chainsaw for 4 years. Its advantages: ease of maintenance, good balance. Disadvantages: some wear on parts. But it does not exceed the wear of other instruments.”

Evgeniy, Ildibaevo: “I’ve been using Poulan 2150 for a long time. I work on orders, harvest timber. I use the saw often. Recently the piston group flew. I couldn’t find any parts, so I contacted service. We installed parts from another saw. Works great".

The cost of Poulan products is about 5,200 rubles. Some models are sold for 4,700 rubles. Professional tools cost RUB 8,415. Prices in different regions of the country may vary.

Adjusting the Husqvarna chainsaw carburetor

General view of the Husqvarna chainsaw carburetor and adjusting screws:

A distinctive feature of this saw is the ability to operate at low idle speeds. In the instructions, the manufacturer notes the following: on a correctly adjusted device, the minimum idle speed is 600...700 rpm. If work occurs at a higher crankshaft speed, the chain will not stop in idle mode. This is dangerous for the user.

To correctly adjust the carburetor, place the chainsaw on a horizontal surface.

Before starting the adjustment, you need to allow the internal combustion engine to warm up for 8...10 minutes (in summer) or 12...15 minutes (in winter, at negative air temperatures).

Turn screw L on the carburetor clockwise. Having reached the limit position, they return back approximately a quarter turn counterclockwise.

The idle speed is set with a screw marked T. Turn this screw clockwise and watch the chain begin to move. As soon as the chain starts to move, turn the screw back until the drive sprocket stops rotating. The chain will stop.

Screw H determines the quality of the mixture at maximum speed. If you turn it clockwise all the way, the internal combustion engine will make a lot of noise. The exhaust will be smoky and the mixture will be too rich in the carburetor. Therefore, from the maximum position, reverse rotation is performed approximately half a turn back.

Recommendations for adjusting the carburetor on Husqvarna saws are shown in the video:

How to properly adjust the carburetor with your own hands?

After washing and thoroughly cleaning the carburetor, they are assembled and begin to be adjusted. First of all, you need to understand the purpose of the adjustment screws. This will help the instructions, but some general points should be addressed immediately. The most common screw designation is:

• N. _ Regulates the state of the main jet, i.e. Sets the maximum rotation speed of the motor shaft;
• L. _ Regulates idle nozzles (responsible for the minimum shaft rotation speed);
• T. _ Regulates engine idle speed. It can also be marked with the letters LA or S; on some carburetor models it is completely absent.

Turning screws H and L clockwise depletes the air-fuel mixture and enriches it counterclockwise (the amount of gasoline increases). When screw T rotates, the shaft rotation speed changes at idle speed. Clockwise, it increases and decreases in the opposite direction.

Figure 2. Carburetor adjustment mechanisms

Before taking direct action, it is necessary to find and carefully study information about the position of the adjusting screws (the value of the angle of rotation during adjustment). This information is available in the chainsaw manual. Then you need to prepare your workplace. Lay the saw on a flat, horizontal plane with the chain facing away from you. Remove all covers, foam and air filter. At this point, the preparatory operations are considered complete, and the main part of the work can begin.

Procedure for setting carbohydrates:

1. Carefully tighten screws H and L clockwise until they are tight, being careful not to break the screws. This will result in complete loss of the carburetor.
2. Unscrew both screws one and a half turns.
3. Run the engine for 10 minutes and warm it up. This is a necessary point because the carburetor cannot be installed correctly on a cold engine.
4. By turning screws H and L, alternately adjust the rotation of the shaft at maximum and minimum speeds.
5. By adjusting the position of screw T (or it may have another designation), the idle speed of the chainsaw is adjusted. It is necessary to achieve smooth and stable operation of the engine. It is important to monitor whether the circuit is in standby mode or not. If it moves, turn the screw slightly counterclockwise.

READ Chainsaw Carburetor Adjustment Wrench

Check engine operation visually and audibly. A mixture that is too rich results in thick smoke from the exhaust. When a lean mixture is fed while the saw is running, a whistle is heard. Excessive saving is harmful. If you set the L screw to "bad" fuel, you will have problems starting the engine. When set to a lean mixture, screw H will noticeably lose strength. You can determine the correct setting by the following criteria:

• At idle, the engine does not lag and the chain does not move;
• There is no excess smoke from the exhaust pipe when the engine is running;
• The engine exhibits good throttle response (it quickly picks up speed when you press the accelerator).

A detailed description of the setup is available in the instructions included with the instrument in the package. This should be carefully reviewed as there may be some features or special requirements set by the manufacturer that only apply to that model of saw. If all requirements are met accurately, the chainsaw's performance will be restored to its original condition.

Adjustment Tools

To adjust the carburetor, you will need Phillips or slotted screwdrivers of varying lengths or thicknesses. The size depends on the design of this unit and the characteristics of the engine assembly. It should be noted that some manufacturers produce carburetors designed for use with special tools.

In particular, installation of Husqvarna carburetors and other imported tools may require a special screwdriver. It is advisable to clarify this issue even when purchasing a chainsaw, so that you can purchase the necessary additional equipment in advance.

In addition, washed gasoline or acetone will be needed to flush and clean the device. They are used to clean the external surfaces of the carburetor. All internal channels are washed with kerosene, diesel fuel or white alcohol. Before washing the carburetor, remove all rubber or plastic parts that may come into contact with aggressive chemicals.

Wrenches or ring wrenches are used to disassemble the carburetor. Washing of internal channels is carried out in specially designated baths; sometimes plastic syringes are used for this.

Review

• Basic equipment and production of the Poluan chainsaw
• Characteristics
• Features of use and safety
• Maintenance and Operation Instructions

Carburetor adjustment

• Advantages and disadvantages
• Review
• Reviews from Poulan 2150 chainsaw owners

In the gardening market, the Poulan two thousand one hundred and fifty chainsaw has long been a leader. The instrument gained such popularity due to the high quality of materials, power, performance, light weight and small dimensions.

Low fuel and oil consumption makes the Poulan chainsaw extremely economical. The product is falsely assigned to a certain class, so I consider it universal. This is due to the fact that the Poulan two thousand one hundred fifty chainsaw is ideal for both home use (harvesting firewood, sawing dead wood) and professional use (felling trees, sawing wood, etc.)

Purpose, design and principle of operation of the carburetor.

A carburetor is needed to prepare the air-fuel mixture to power the engine. If the proportions in this mixture are incorrect, the operation of the motor is disrupted. If the proportion is not observed in the direction of increasing the amount of fuel, the mixture is called oversaturated, but if, on the contrary, there is little fuel, it is called lean. Both have a negative effect on engine performance.

In different models of chainsaws, carburetors differ in design, but they are similar in principle of operation. The air flow moves at high speed along the air channel. The damper that blocks the channel allows you to change the speed of the air stream. The fuel is supplied through the atomizer into the channel, where it is mixed with the incoming air, forming an air-fuel mixture. The resulting mixture enters the engine.

The pressure in the float chamber, where the fuel is located before mixing, is almost equal to atmospheric pressure. But a vacuum is created in the air channel, due to which the fuel is drawn into the air flow. The more the damper opens, the faster the air moves, and the amount of fuel also increases - the engine speed increases. This is how you can imagine the principle of operation of a carburetor in a simplified way.

For efficient, smooth operation of the tool, obtaining maximum output and at the same time economical fuel consumption, you need to adjust the carburetor of the chainsaw. Before adjusting, you need to check the fuel and air filters - they must be clean. On most chainsaws, adjustment is carried out by three screws: idle, high speed, low speed. The following signs indicate that the carburetor is correctly adjusted:

1. The chain does not move at idle.
2. The engine accelerates smoothly and quickly.
3. The sound of the running engine is smooth, similar to the sound of a four-stroke engine.

When adjusting the carburetor, you need to treat it with all possible care, because errors in the settings can lead to very serious consequences, including engine malfunction. If you are not 100% confident in your abilities, you need to contact a service center.

What carburetors are used on Chinese chainsaws

The most optimal carburetor designs for chainsaws were developed by the world's leading manufacturers - German Stihl, Japanese Walbro and others. These top developments are hard to beat. Therefore, most Chinese manufacturers copy the best models.

Today there is a large offer of Chinese carburetors for chainsaws on sale.

Some are nameless, from an unknown manufacturer and do not even have markings. They are simply offered for a specific chainsaw model. For example, a carburetor for a Stihl MS 361 chainsaw.

Others have brand names of well-known brands.

Still others have their own catchy names - in Russian transcription King Kong, Technopark, Rezet and others.

What kind of carburetor does your chainsaw have?

A carburetor removed from a chainsaw and cleaned of carbon deposits looks something like this in most models. The figure clearly shows the designations of the adjusting screws.

It's easy to remember their designation:

• LA (in some T models) – idle speed adjustment. This screw is brought out in all chainsaws.
• L and H – adjustment of the position of the rocker arms (gaps for fuel supply), that is, selection of optimal speed under load. In some instruments, especially inexpensive ones, they are not brought out, but the holes, so that you can get to them without removing the cover, are usually decorated with plastic tubes. Screw L regulates the flow of fuel mixture into the engine at low speeds, screw H – at high speeds.

The owner of a chainsaw does not have a special adjustment stand, and prefers to make adjustments without disassembling the unit or disassembling it minimally. Before disassembling for the first time, be sure to study the operating instructions, especially the section describing the design and containing a set of sketches. This preparation will allow you to avoid unnecessary disassembly and assembly work.

When is carburetor adjustment necessary?

Initially, from the moment the tool is sold, all carburetors are tuned and tuned at the factory. However, during operation, the settings are gradually lost and the operation mode changes according to the operating conditions. Carburetor symptoms may include:

• The gas flow is too high, thick smoke comes out of the exhaust pipe;
• The engine power is clearly insufficient for normal tasks;
• Engine speed "float";
• After starting, the engine stops immediately or after a few seconds;
• It is generally impossible to start the engine;
• The chainsaw “shoots” and sharp spikes appear in the tool’s engine.

READ How to Cut Slate Without a Grinder

It should be noted that when a new engine breaks down, the carburetor is set to deliver less fuel to limit engine power. After a breakdown, the fuel supply increases to the nominal value. These adjustments are made using adjustment screws on the carburetor body (usually two or three).

User manual

Owners often face a problem: it is difficult to find instructions written in Russian. Let's compose it ourselves. Operating instructions for the Poulan chainsaw:

1. A saw is a tool that can do both good and harm. It must be handled with care.
2. It is necessary to periodically clean the unit, adjust the main systems and replace consumables.
3. Use chains for Oregon 91VJ or 91VG models.
4. The tool has a comfortable grip and good balancing.
5. Has high performance.
6. It is recommended to run-in the unit without load before using it. To do this, you need to burn about 3 tanks of gasoline (about 1 liter).
7. To assemble the tool, you must use a combination wrench.
8. Install the bar, put the saw chain on it and tighten it with two nuts.
9. A-92 gasoline mixed with oil in a ratio of 50/1 is poured into the gas tank.
10. The work area must be prepared: children and pets must be removed.

The requirements of the manual are mandatory.

Carburetor adjustment

The engine operates based on a mixture of gasoline and oil. A rich or lean mixture negatively affects traction and reduces the life of the unit. At the factory, the chainsaw carburetor is adjusted according to average values. When adjusting with your own hands, you should remember that the composition of the mixture can be changed by rotating the screw for the quantity and quality of the mixture.

To properly adjust the carburetor, you need to know its structure and the purpose of each part well. Only in this case can the setup be done by hand.

On the carburetor, some adjusting elements cannot be unscrewed. They have heads with special slots that our screwdrivers do not fit into.

Repair work

If there are problems with operation, you can repair the chainsaw yourself. This device has a high level of maintainability. Spare parts are sold in special stores and are easily replaced. The advantages of the Poulan model range include:

• affordable prices for spare parts;
• economical consumption of oils and fuel;
• easy access to all product systems;
• use of oil from European manufacturers.

The package includes instructions with a list of recommendations, which includes:

• preparing the saw for work;
• systems maintenance;
• starting the engine in winter.

In case of malfunctions, the culprits may be:

• low quality fuel and lubricants;
• poor cleaning of the air filter;
• debris or drops of water getting into the carburetor;
• faulty spark plug;
• short circuit in the wiring;
• excessive chain tension;
• Incorrect carburetor setting.

The saw's ignition system is electronic. It does not require care or maintenance. You just need to monitor the quality of the spark plug and wires.

Owner reviews

Nikolay Astakhov, 44 years old, Primorsky Territory:

I bought the Poulan 2150 saw four years ago. I use it regularly, mainly for harvesting and sawing firewood. My assembly is still American, according to the documents. No special problems were identified during this time. The motor runs fine, the tire and chain are of acceptable quality. During all this time I adjusted the carburetor a couple of times and bought a couple of chains.

Victor Rybak, 43 years old, Arkhangelsk region:

Poulan bought the saw as American, but it turned out that it was made in China. However, in terms of the quality of the parts and assembly of the unit, everything is quite acceptable. The engine is practically indestructible. I seriously loaded it - it cuts perfectly. Of course, during this time it was not without problems. The main one is the carburetor. It has to be adjusted regularly. The Poulan 2150 chainsaw is very susceptible to air filter contamination: it gets a little dirty and the speed already fluctuates.

Advantages of the Poulan model: price, high-quality engine, no vibration;

Disadvantages: carburetor settings are often lost, Poulan reacts strongly to air filter contamination.

How to troubleshoot carburetor problems

The main malfunctions of a chainsaw carburetor may be as follows.

• The engine starts with difficulty and stalls a few seconds after starting. This is often caused by incorrect low rpm settings. The fuel-air mixture is slightly enriched. It is necessary to unscrew the “L” screw half a turn, after which the adjustment should be completed with the “T” screw.
• Engine power decreases noticeably under load. This means that the carburetor excessively enriches the mixture with oxygen. Therefore, screw “H” needs to be tightened a little, about 1/8 of a turn. If after such actions the engine power is still insufficient, but there has been some improvement in its operation, then the regulator can be tightened a little more.
• The engine at maximum speed and without load begins to “sing”. This malfunction in the operation of the unit is caused by a lean mixture and high speed. The adjustment is made using the same “H” screw.
• No gasoline enters the combustion chamber. Failure can be caused by clogged fuel filter, channels and carburetor jets. To eliminate the malfunction, you need to completely disassemble this chainsaw module and blow out its channels with compressed air (a compressor is required). To properly clean the fuel channels, you can use a special carburetor flushing fluid. Also, the lack of fuel flow into the engine cylinder may be due to incorrect adjustment. How to do this yourself is discussed above.
• Overfills the carburetor. In 90% of cases, fuel overflow is caused by a dried out and roughened membrane, which puts pressure on the rocker arm connected to the needle. To change it, you will need to remove and disassemble the carburetor.
• The engine revs poorly, runs intermittently, and power decreases. These problems are often caused by a clogged air filter. You will need to remove the cover covering the filter and clean it, which involves washing with detergent.

In general, timely adjustment, as well as timely repair of a chainsaw carburetor can significantly extend the life of the entire engine piston system

Therefore, the setting of this component of the fuel system must be treated with great attention.

Features of the Chinese chainsaw carburetor

Their design and parameters differ depending on the power and model of chainsaw they are intended for. All of them are almost identical to the original carburetors in design, but not always in quality. Today, all Chinese products cannot be considered 100% rubbish. In turn, according to their quality, they can be divided into three groups:

1. Poor quality. Unsuitable alloys are used which oxidize, crumble and break. There is no accuracy of fit, the calibrated holes do not correspond to the required values, which leads to excessive consumption or lack of fuel in the combustion chamber. Critical parts quickly fail. Plastic parts quickly become rough or, conversely, become softened by gasoline and stop working. The axles and wire rods are bent, the threads of the fasteners are torn off. Such products are the cheapest. They are made in semi-handicraft industries using adapted equipment. As a rule, they do not have a name or marking.
2. Carburetors are of average quality. These are factory assembled products. They do not skimp on alloys; they have established continuous production with quality control. These are fully functional carburetors that can have a service life even longer than that of the entire chainsaw.
3. High quality carburetors. First of all, these are products from global manufacturers whose facilities are located in China. Geographically, they can be considered Chinese, but they are made using the technologies of the company that owns the brand and values ​​its reputation. For example, Japanese Walbro carburetors are produced in China.

In addition, among Chinese manufacturers there are those who rely on high quality. They invest heavily in powerful production facilities, register their own brand and work on its reputation.

Review of popular Poulan chainsaw models

Let's get acquainted with some popular representatives of the Poulan brand and their characteristics in more detail.

Poulan 2150

The Poulan 2150 chainsaw is one of the most purchased representatives of the entire model range of the American brand in our country. Refers to household saws. However, with a power of 1.3 kW, it can be used for work beyond simple construction and renovation.

Poulan 2150 is characterized by a structure typical for a number of chain saws. The internal contents, protected by a durable plastic case, consist of a carburetor, a two-stroke engine, an ignition system including a coil and a spark plug, a starter - starting device, a fuel pump designed to pump gasoline into the carburetor.

The Poulan 2150 chainsaw, like all other modern chainsaws, has two tanks: fuel for the engine and oil for lubricating the chain. The fuel oil-gasoline mixture is prepared in a ratio of 1/50. The chain and bar are automatically lubricated, which increases the service life of the cutting set.

This model has the following features:

1. The high-strength plastic from which the saw body is made can withstand any damaging impact.
2. The material of the side part is aluminum alloy.
3. The handles have a convenient location for working with the saw.
4. The durability of the motor is ensured by an additional protective layer that covers the cylinder-piston group.
5. The anti-vibration system, made of steel springs, successfully dampens all unnecessary vibrations.
6. The oil pump required to supply oil to the chain has no manual adjustment.
7. The presence of a primer that serves for instant start-up at any operating temperature.
8. Nylon filter, easy to maintain and replace.

Poulan 2150 also has a tire length of 40 cm, a crankcase and gas tank volume of 0.2 l and 0.35 l, respectively, and a weight of 4.7 kg.

Poulan 2250

The Poulan 2250 chainsaw has many useful functions in everyday life. Great for gardening. But in order to perform more complex work, it is better to purchase a professional model.

Has the following features:

1. To protect the cylinder-piston group from corrosion, chrome plating is used.
2. Chain brake that can be activated either by inertial force or manually.
3. Automatic oil supply for lubrication of the cutting set (manual adjustment is not provided).
4. Primer is a pump that pumps fuel for cold engine starting.

In addition, this model has a power of 1.3 kW, a tire length of 40 cm, crankcase and fuel tank volumes of 210 ml and 360 ml, respectively, and a tool weight of 4.7 kg.

Poulan 1950

This tool has an average price. Poulan 1950 is popular among people who are just starting to work with gasoline saws, and among professionals who have been working with wood for a long time.

Features of the Poulan 1950 saw:

1. Characterized by good structural balancing.
2. High quality saw set. The bar length is 40 cm, the chain pitch is 3/8 inch.
3. Adjusting the oil supply for chain lubrication. The amount of lubricant supplied corresponds to the load of the gasoline engine.
4. Easy to clean nylon filter.
5. The presence of a primer that makes it easier to start a cold engine.

Chainsaw Poulan P2250 – features and benefits

This reliable Paulan model is designed for intensive household use. Chainsaws are often also used by professional builders, utility workers, and fellers to clean the trunks of large trees before final cutting.

The Poulan 2250 chainsaw is equipped with a 2-stroke single-cylinder gasoline engine. The power of the internal combustion engine at maximum loads is 1.3 kW. The volume of the working standard cylinder is 38 cm3. The walls of the element are coated with a chrome alloy, which protects the cylinder from corrosion and mechanical damage.

The internal combustion engine of this Poulan chainsaw is distinguished by a solid reserve of torque. At maximum engine loads, this technical characteristic of the model is 12,000 rpm. This makes it possible to use the tool for occasional cutting of large trees, as well as longitudinal sawing of logs.

To start the tool, it comes standard with a fail-safe recoil starter. It is equipped with an enlarged drum with an impeller, which cleans the air as it enters the carburetor. The motor is cooled using an innovative forced air supply system.

The factory configuration of the Paulen saw includes large tanks for filling fuel and oil. The tanks have wide necks, which makes refilling faster and more convenient.

The working parts of the model are represented by a proprietary tire and chain. The headset does not require regular maintenance. The chain is lubricated automatically using a pump.

All internal spare parts of the Poulan chainsaw are placed under a durable plastic case. It is made of multi-layer polymers that can withstand shock when dropped from a small height. If necessary, elements of the protective case can be removed, which greatly simplifies the repair of the instrument.

Model specifications include:

• The power of the standard internal combustion engine is 1.8 liters. With.;
• maximum speed when the engine is idling – 3000 rpm;
• the length of the standard tire used is 40 cm;
• the pitch of the chain provided in the package is 3/8 “;
• working weight – 4.9 kg.

The standard delivery package of this Poulan chainsaw includes a key, a detailed instruction manual, as well as a branded bar and chain.

How to flush a chainsaw carburetor?

You can clean the carburetor on a chainsaw using any aerosol cleaner. The brands Mannol, Hi-Gear and Nowax have proven themselves best. These compounds are good at cleaning the walls and parts of the carburetor from accumulated dust, carbon deposits and hardened resin.

Both Chinese and German carburetors are washed in the same sequence.

Cleaning the carburetor on a chainsaw is performed in the following order:

• First, you need to drain the used fuel remaining in the fuel tank. Next, you need to unscrew the mount and remove the protective cover of the chainsaw body, and also remove the standard air filter;
• Next, you need to remove the hose responsible for supplying fuel. To do this you will need to open the latches. After this, you need to unscrew the fasteners and remove the top cover of the factory assembly housing;
• Next you will need to remove the cover with the blue gasket, which plays the role of a fuel pump membrane. Near the body there are brackets in the form of springs. They will need to be removed and the screws removed;
• Then you need to unscrew the screw and carefully remove the needle valve. Directly below it is a built-in spring, which also needs to be removed. After this, you need to pull out the damper and the standard axle, carefully pulling them along towards you;
• After this, you will need to remove the drive arm, as well as the throttle body and its factory axle;
• All extracted parts of the chainsaw carburetor will need to be laid out on paper and their integrity checked. If necessary, worn parts must be replaced;
• Next, all dismantled parts must be washed with a spray can. The same must be done with the float chamber and carburetor body.
• After complete drying, all parts must be installed in the reverse order.

After washing, the carburetor will need to be installed in its regular place in the chainsaw. Next, you will need to start the garden tool and observe its operation at idle and maximum speed.

Chinese chainsaw carburetor repair

Carburetors cost 500-1000 rubles. It doesn't always make sense to repair. A repair kit with a set of gaskets and a diaphragm costs not much less than the cheapest carburetor, 300-350 rubles. A frequent breakdown of Chinese carburetors is the failure of the injector valve, and such a part is not sold in repair kits. Therefore, it is easier to buy a new carburetor.

But there are breakdowns that can be relatively easily fixed on your own:

Loss of seal between parts of the carburetor body or between the carburetor and the engine. Sometimes it is enough to tighten the fastening screws. In other cases, you can remove the carburetor, replace the gaskets, or use a suitable sealant along with them.

Obvious mechanical problems - deformation of the wire rod from the throttle, sticking of the axes on which the throttle and air dampers rotate - are also easy to fix. The thrusts are straightened. The axle landing sites are lubricated with a drop of oil and free rotation is developed by hand.

Carburetor cleaning

The carburetor air filter needs to be cleaned periodically. They come in different types. From some it is enough to knock out dust and dirt by knocking on wood. Others are washed with soapy water. Still others require disassembly. The fourth ones are almost impossible to clean; they need to be replaced with a new one.

The features of the air filter for each chainsaw and maintenance rules are described in the instruction manual for each specific model.

If there is a filter in the gas tank, nothing can become clogged in the carburetor. If there is still a suspicion that the tiny holes in the jet are clogged, the carburetor is disassembled. The parts are laid out on a clean cloth, remembering which one comes from where. The holes are purged with a pump or compressor. The body and parts are washed in kerosene or gasoline.

There is no need to bring the condition of the filters to such a deplorable state. This greatly affects the performance and life of the chainsaw engine.

Gasoline does not flow into the carburetor: what to do

The fuel line from the gas tank is short and uncomplicated. Three problems may arise in this area:

• The gasoline supply hose is pinched. The break is found, the hose is straightened or replaced if the round shape is not restored.
• The filter at the bottom of the gas tank, which is installed on some models of chainsaws, is clogged. It is removed with a thin wire hook, inspected and cleaned. The gas tank is flushed with gasoline.
• The breather has failed. When fuel is sucked in, a vacuum is created in the gas tank, and fuel flows poorly or does not flow at all. This part cannot be repaired. Most often, the breather is located in a hard-to-reach place, at the outlet of the fuel line from the gas tank. It is replaced with a new one.

Sometimes, instead of repairing the breather, a hole with a diameter of 0.2-0.5 mm is made in the gas tank cap. The downside is that gasoline may leak through the hole during operation, and after operation the chainsaw can only be placed on its side, with the gas tank cap facing up.

How are things going with repair kits?

The repair kit can be purchased at the same retail outlets where carburetors are sold. They are sold in two configurations:

• rubber-plastic parts (gaskets, diaphragm)
• the same thing, plus a cross with a needle valve.

It is difficult to find other spare parts separately.

Chainsaws "Poulan" - ideal quality at competitive prices

An American brand that has stood the test of post-war devastation, competition and fame, which could not spoil it in the slightest. It all started in 1944, when K. Poulan, the founder of the company, decided to produce not wartime equipment, but garden tools that would help the country escape from the embrace of the echoes of war. Such units were a curiosity at that time, but were able to quickly occupy an important niche in every household or agricultural enterprise. Today, the power of this company traditionally pleases us with its accessibility to the masses, high quality and long service life. Unlike other global brands, it has remained faithful to its homeland, which is why production facilities are localized exclusively in the USA, which also needs to be taken into account when purchasing Poulan equipment ", marked "made in China" or Europe.

Poulan chainsaws: review of the model range

A household or semi-professional chainsaw is available in almost every private household or farm. The presence of such a tool makes it possible to effectively mechanize most of the labor-intensive work of dumping decommissioned dead wood, collecting firewood, and erecting wooden building structures for various purposes.

The household tools market offers a small selection of American Poulan chainsaws, which successfully compete with similar products from leading European brands. The manufacturer is a well-known company from the USA, which annually produces more than a million units of modern, reliable and affordable chainsaw equipment.

Theory and principles of operation of the fuel system, carburetor design

The principle of operation of the carburetor

In different models of chainsaws, the design of the carburetor may differ, but the principle of operation of this part is always the same: the forced air flow moves in the direction of the air (pulse) channel, the air is regulated by the air damper. Entering the pulse channel, the air changes speed. The change in speed is affected by a special valve that closes the air inlet. Fuel is supplied into the air channel and mixed with the air flow. As a result, a flammable fuel-air mixture is formed, which then enters the engine and burns there.

Figure 1. Diagram of the operating principle of a chainsaw carburetor

Diagram of the operating principle of a chainsaw carburetor

Figure 2. Carburetor of the Husqvarna 137 chainsaw

Carburetor of Husqvarna 137 chainsaw

Figure 3. The principle of operation of the fuel system using the example of a chainsaw carburetor with a two-stroke engine

The principle of operation of the fuel system using the example of a chainsaw carburetor with a two-stroke engine

The components of any carburetor are:

• aluminum body (solid, cast);
• jets or valves that regulate the amount of fuel entering the carburetor;
• float chamber;
• diffuser;
• spray.

In Figure 1 you can see the location of the key components of the carburetor, and in Figure 2 you can see the appearance of the chainsaw carburetor. To properly adjust the carburetor, the chainsaw owner should know on what principle this part works:

• when the engine starts, the air damper opens;
• due to the stroke of the piston, rarefied air is formed inside the float chamber and in the air channel;
• then the mass of air is sucked through the diffuser, where it is mixed with fuel, which also passed through the fitting into the float chamber, thus creating a fuel-air mixture entering the intake channels;
• the last stage is the mixture entering the engine combustion chamber.

By adjusting the position of the damper, the chainsaw owner can either add air to the fuel or deplete it - this means that the fuel mixture will enter the combustion chamber faster or slower. Carburetor adjustment screws are used to adjust engine speed. An air filter is installed above the carburetor, which cleans the air before it enters the air duct.

Video showing a table for adjusting the carburetor of a Husqvarna chainsaw:

Figure 4. Table of proportions of oil-fuel mixture for Husqvarna chainsaws

Table of proportions of oil-fuel mixture for Husqvarna chainsaws

The carburetor unit of expensive and medium-cost chainsaws is designed almost identically. Cheap Chinese chainsaws often differ from expensive original chainsaw models in that they lack a number of parts in the carburetor unit. You can read about the features of adjusting the carburetor of Chinese chainsaws later in the article.

Step-by-step sequence of the adjustment process

Before you begin making adjustments, remember:

• the adjustment is carried out only “hot”, that is, the engine needs to be started and warmed up for 10 minutes;
• then the adjusting screw is turned counterclockwise and the chainsaw chain is stopped;
• before adjustment, the chainsaw must be placed on a flat surface, and the saw part must be directed away from the owner;
• for adjustment, three screws with letter designations are used, H - adjusts the upper speed, controls the main jet, L - adjusts the idle jet, adjusts the low speed, T - adjusts the idle speed.

Carburetor adjustment step by step:

• Scroll screw L from left to right, or from right to left, find the maximum engine speed, then return 1/4 turn back;
• do the same actions with screw H;
• the chainsaw should run for a few seconds, the maximum engine speed is determined using a tachometer - their indicator should not exceed the maximum specified in the instructions for the chainsaw;
• if the chain moves in idle mode, turn screw T in the direction of chain movement until the chain stops completely (idle speed is always adjusted only by screw T, which is rotated from right to left - counterclockwise - until the chain stops completely).

• the threaded fastener has weakened, air penetrates through the resulting gap;
• the jets are clogged with resinous deposits and need to be flushed with acetone;
• The ignition is not adjusted.

Related Posts

Installing a chainsaw carburetor. Or how not to pay repairmen!

Using a chainsaw makes life much easier even for an amateur, and in some professions this tool is almost indispensable. However, like any relatively complex device, a chainsaw requires periodic maintenance. Due to untimely or inadequate maintenance and due to the impact of both planned and excessive loads, various malfunctions can occur. For professionals, interruptions or unstable operation of the saw reduces work efficiency or can lead to a ruined workday. One of the most common malfunctions is incorrect adjustment of the chainsaw carburetor, which gets lost due to unsuccessful attempts to adjust or switch the adjusting screws for other reasons.

Symptoms of malfunctions and failures that require carburetor adjustment.

The following signs and malfunctions indicate the need for carburetor adjustment:

• the engine starts with deformation and stops almost instantly;
• gasoline consumption is excessively high, the exhaust is too thick, the combustible mixture in the cylinder does not burn completely;
• the factory settings of the chainsaw carburetor were lost (due to vibrations or unsuccessful attempts at adjustment);
• malfunction of the air purification system, which led to debris entering the fuel distribution mechanism;
• significant wear of the piston group. Carburetor adjustment
  in this case acts as a temporary measure.

It is clear that when dirt gets into the fuel system with one installation, the problem cannot be solved. washing is required. If the piston is worn, a major overhaul is required. However, in all these cases the carburetor is also tuned.

Purpose, design and principle of operation of the carburetor.

The carburetor is necessary to prepare the fuel-air mixture for engine power. If the proportions in this mixture are incorrect, engine operation is interrupted. If proportion to the increase in the amount of fuel is not observed, the mixture is said to be supersaturated, if fuel, on the other hand, is unlikely to be present. At work, the engine is both not the best way.

In different chainsaw models, carburetors differ in design, but they are basically similar in operation. The air flow moves at high speed along the air channel. A damper that closes the channel allows you to change the speed of the air stream. The fuel is fed through the atomizer into the channel, where it is mixed with the incoming air, forming a fuel-air mixture. The resulting mixture enters the engine.

The pressure in the float chamber, where the fuel is mixed before mixing, is almost equal to atmospheric pressure. But the air passage creates a vacuum so that fuel is drawn into the air stream. The more the flap opens, the faster the air moves and the amount of fuel increases. engine speed increases. Therefore, it is easy to imagine the principle of a carburetor.

Advantages and disadvantages

Speaking about technical characteristics and parameters, ergonomics and efficiency, reliability of materials, mechanism and parts, the American Poulan saw has a lot of advantages.

• reasonable price for tools, spare parts, repairs and maintenance;
• reliability and excellent quality, which guarantee a long service life without frequent and serious breakdowns;
• economical consumption of fuel and lubrication oil;
• ergonomic design, convenient design of the body and position of the handle, so that the operator does not get tired;
• good vibration absorption system.

Speaking about shortcomings in the design and operation of the Poulan 2150 chainsaw, relying on reviews and the manual for the tool, it is difficult to identify them even after several years of active use.

Reviews

Reviews that can be found on the Internet:

I do part-time work in forestry. The workers there use, of course, professional saws, and they gave me a Poulan chainsaw. I liked the unit, it is easy to start and convenient. Vibrates to a minimum, works for a long time without cooling, even when it’s hot outside. (Dmitriy).

I have been using a Poulan saw for almost 5 years, the experience is positive, I am satisfied with the reliability of the plastic parts. (Fedor).

Of course, there are reviews pointing out some shortcomings of these saws. For example, owners talk about the lack of visible control of the amount of fuel and oil in filling containers.

Poulan chainsaws are a tool whose different models are very convenient for household work. Based on the majority of owner reviews, we can talk about reliability, high quality, and good characteristics of American Poulan saws. Despite some shortcomings indicated by customers, these chainsaws are a good option at an affordable price.

Chainsaw engine malfunction

Signs of a chainsaw engine malfunction:

– the engine does not start – the engine runs unsteadily – the engine starts, but very often stalls – the engine quickly overheats – the engine runs normally at idle, but “chokes” under load – the engine smokes heavily, power drops

In certain situations, it is better to seek help from professionals and take your saw to an authorized service center. But you can deal with some problems yourself.

In general, in order to eliminate the cause itself, you must first correctly identify it, otherwise the entire repair will be tantamount to shooting at sparrows from a cannon, and perhaps even shooting at “fictional” sparrows, since there may not be any breakdown.

If you are trying to start a chainsaw, but it does not start, and at the same time does not make any strange sounds that are not typical for it (knocking, grinding), then you are simply starting it incorrectly (if you pull the chainsaw on the choke for a long time, the internal combustion engine is filled with fuel, and then start its difficult).

How to start a cold engine correctly? 1. Set the lever or switch to the “flap closed” position. 2. If the model is equipped with a fuel priming pump, pump the fuel mixture into the carburetor. 3. Pull the starter handle until resistance appears, then vigorously pull in amplitude, moving your hand to the side (2-3 times). No need to try to “rip” the starter cord out of the chainsaw! The saw should start and then stall. 4. If the engine does not start, move the lever to the half-throttle position or to the working position, and try to start the chainsaw in this mode

Please note: some models have a push-button ignition switch, make sure it is turned on

What to do if the engine still doesn’t start? First, unscrew and inspect the spark plug. It happens that when starting a chainsaw in cold weather, the combustion chamber is accidentally filled with fuel mixture. In this case, you should also unscrew the spark plug, dry the combustion chamber by idling, clean the spark plug, and try to start the saw again.

How to check for spark on a spark plug? Place the unscrewed spark plug connected to the high-voltage wire on the cylinder and pull the starter. Be careful! You cannot touch the candle with your hands during this procedure! If you see a blue spark, the spark plug is OK. We screw the spark plug into place and try to start the saw again. If we fail again, we’ll check the connection of the high-voltage wire to the spark plugs, the coil and the ignition system.

Based on the state of the spark plug, you can understand what happened to the saw:

• Dry candle. Apparently, the fuel mixture will not get into the cylinder. The problem is not in the spark plug, so we screw the spark plug back in. And we check the fuel supply system.
• A wet, heavily fuel-stained spark plug. The reason for excess fuel is hidden either in violation of the model factory rules, or in incorrect carburetor adjustment.
• The candle was covered with black soot. This may indicate the use of low-quality oil (so use only original oil for your saw), an incorrectly adjusted carburetor, or an incorrectly prepared fuel mixture. The spark plug needs to be washed, thoroughly cleaned of carbon deposits with an awl or a needle, the electrodes should be wiped with sandpaper and screwed into place.

When checking the spark plug, pay attention to the gap between the electrodes (it should be 0.5 - 0.65 mm). A worn gasket must be replaced

Video review

Let's take a closer look at some popular representatives of the Poulan brand and their features.

chainsaw Poulan 2150

During its existence, the company has launched several dozen gas-powered chain saws on the market. Most of them are obsolete and are no longer produced. Some models have already been discontinued, but still serve their owners faithfully and can still be purchased on the used equipment market.

Starting a Poulan chainsaw

The company produces many models of gasoline-powered saws, but here we will look at the most popular ones, which are in great demand among customers and about which satisfied owners leave positive reviews.

The chainsaw is equipped with systems for automatically lubricating the chain with oil, as well as cooling the headset during operation. This model is characterized by economical oil consumption and automatic control of the amount of necessary lubricant for comfortable and smooth operation.

Additionally: Which chain is best for a chainsaw: review, tips for choosing. Chainsaw chain with pobedit tips

Poulan 2150 belongs to the semi-professional saws, since it has an extended engine life and is the most popular semi-professional class saw. Manufacturers took care of the durability of spare parts and applied a silicon-nickel coating to the piston group.

The plastic from which the chainsaw is made is impact-resistant and resistant to temperature changes during operation. The vibration damping system and crankcase design have been improved. But the traction and consumption technical characteristics of the Poulan 2150 saw are the same since 1950.

Poulan 2250 is already a much more serious model with a larger two-stroke engine, 45 cm3, 1.4 kW power and with a tire extended to 45 cm. The technical capabilities of the saw have been enhanced by an inertia brake, and careful work has been carried out to strengthen the vibration and noise reduction system.

Chainsaw Poulan 2250

The semi-professional Poulan 295 with a powerful 3 horsepower engine will easily cut through frozen and hard wood. The best-in-line noise and vibration damping system, thanks to which you can work with the chainsaw for a long time and continuously without fatigue.

Chainsaw Poulan PP 295

Automatic lubrication of the chain, chrome-plated cylinder, air filter and engine dust protection system significantly increase the service life of the chainsaw. The characteristics of this saw are very similar to the Poulan 260 PRO, however, the second model has slightly weaker technical indicators.

Poulan chainsaws are very popular among customers. Models of the American brand become excellent helpers in everyday life when working in the garden, making repairs, doing small carpentry work and more. This article is about the features of Poulan saws, about the characteristics of different representatives of the model range.

Today, gas trimmers, scythes, brush cutters, cultivators, and walk-behind tractors of this brand are flying off with a bang to all corners of the planet. Every average family can afford them: they are inexpensive and do not require expensive spare parts. But it’s not only budget service that makes them favorites of summer residents and farmers. Quality in the best American traditions and functionality are important reasons to think seriously about purchasing them.

Devices, the production of which occurred in the first years of the existence of the Poulan brand and continues to this day - chainsaws. What distinguishes them from many other brands is:

• mobility and maneuverability;
• multitasking;
• the propulsion systems of these chainsaws are adapted to a wide range of operating conditions;
• ergonomics.

The variety of chainsaws produced is unusually high. We will focus on three of them, the most purchased in our country.

Adjusting the carburetor of the Poulan 2250 chainsaw

The Poulan 2250 chainsaw, like all modern models, has a carburetor adjusted at the factory, but during operation difficulties may arise, which can be resolved by adjusting it. An example of such situations could be chain movement at idle, or problems with idle operation. The solution to both problems is to select the optimal idle speed. It is adjusted with a special screw marked , which is located below the booster pump. The adjustment is carried out using a screwdriver of the appropriate size (the use of a screwdriver is unacceptable). When turning the screw clockwise, the speed increases, and counterclockwise, it decreases. For optimal results, the device must be turned on.

Features of use and safety precautions

In order to avoid injury to the operator, before using the Poulan 2150 chainsaw, it is important to study the operating manual in detail, where special attention is paid to safety precautions.
Only a rested person who is protected by special clothing can operate a Poulan chainsaw. It consists of safety glasses, earmuffs and gloves, fitted but not restrictive clothing and closed, tight boots. It consists of safety glasses, earmuffs and gloves, fitted but not restrictive clothing and closed, tight boots.

Do not forget that fuel is a flammable liquid and, in order to eliminate the possibility of fire, it is necessary to carefully check the Poulan saw for fuel or oil leaks.

Features of Poulan chainsaws

The creation of gasoline saws is considered the first creation established in the company founded by Poulan. For their technical properties, these South American saws have received due recognition from their owners in our country.

Among the features of Poulan brand chainsaws are the following:

• the use of relatively cheap, but high-quality and reliable material in the design of the tool;
• the highest guarantee of safety when working with equipment;
• the presence of a reliable and well-made motor;
• quite high power, but at the same time the weight of the tool is small;
• ease and convenience of work due to mobility;
• multifunctionality.

Comparison of technical and operational advantages of different models

Branded chainsaw equipment Poulan deserves special consideration.

Chainsaw Poulan 1950

This inexpensive model is the lightest and most compact in its category. A carburetor engine with a displacement of 36.3 cm3 and a power of 1.3 kW is used as a power drive. The weight of the tool with the saw set installed does not exceed 4.7 kg.

Despite belonging to the budget category, the tool is equipped with a full-fledged automated lubrication and cooling system for the saw set.

A standard 400 mm long bar and a universal saw chain with a pitch of 38 inches ensure proper performance for various types of sawing work.

Reliable in everyday use, the variable displacement oil pump supplies liquid lubricant to the tire in a dosage determined by engine speed. The complexity of the design is compensated by the economical consumption of chain oil, up to 50%.

Poulan 2150

This model is in high demand in the private sector. The reason for the popularity of the tool is to extend engine life. The wear resistance of the piston group is increased due to the application of a special silicon-nickel coating.

The significant advantages of this development:

• widespread use of impact-resistant and temperature-resistant plastic;
• simplified maintenance of the nylon filter of the air intake device;
• reinforced engine crankcase design;
• an effective vibration damper and a side-mounted chain tensioning mechanism that is easy to access.

The engine consumption and traction characteristics are identical to the previous model.

Poulan 2250

The model is distinguished by an increased volume of a carburetor two-stroke drive with a power of 1.4 kW, increased to 45 cm3, and a branded guide rail extended to 450 mm. The headset is complemented by a reliable inertia brake, and there are more comfortable levels of engine vibration and exhaust noise.

A tool with improved power parameters and a large reserve of torque is aimed at performing labor-intensive and complex work, in particular those related to sawing dense and frozen wood.

The characteristics of the 2250 series saw are as close as possible to the performance capabilities of European semi-professional class models.

Poulan 2550

The most powerful saw in its proprietary line, Poulan 2550 series, is equipped with a carburetor engine with a displacement of 40 cm3 and a power of 2.4 hp. The range of application of the tool includes felling and bucking dead wood with a diameter of up to 400 mm.

Review of popular Poulan chainsaw models

Let's get acquainted with some popular representatives of the Poulan brand and their characteristics in more detail.

Poulan 2150

The Poulan 2150 chainsaw is one of the most purchased representatives of the entire model range of the American brand in our country. Refers to household saws. However, with a power of 1.3 kW, it can be used for work beyond simple construction and renovation.

Poulan 2150 is characterized by a structure typical for a number of chain saws. The internal contents, protected by a durable plastic case, consist of a carburetor, a two-stroke engine, an ignition system including a coil and a spark plug, a starter - starting device, a fuel pump designed to pump gasoline into the carburetor.

The Poulan 2150 chainsaw, like all other modern chainsaws, has two tanks: fuel for the engine and oil for lubricating the chain. The fuel oil-gasoline mixture is prepared in a ratio of 1/50. The chain and bar are automatically lubricated, which increases the service life of the cutting set.

This model has the following features:

1. The high-strength plastic from which the saw body is made can withstand any damaging impact.
2. The material of the side part is aluminum alloy.
3. The handles have a convenient location for working with the saw.
4. The durability of the motor is ensured by an additional protective layer that covers the cylinder-piston group.
5. The anti-vibration system, made of steel springs, successfully dampens all unnecessary vibrations.
6. The oil pump required to supply oil to the chain has no manual adjustment.
7. The presence of a primer that serves for instant start-up at any operating temperature.
8. Nylon filter, easy to maintain and replace.

Poulan 2150 also has a tire length of 40 cm, a crankcase and gas tank volume of 0.2 l and 0.35 l, respectively, and a weight of 4.7 kg.

Poulan 2250

The Poulan 2250 chainsaw has many useful functions in everyday life. Great for gardening. But in order to perform more complex work, it is better to purchase a professional model.

Has the following features:

1. To protect the cylinder-piston group from corrosion, chrome plating is used.
2. Chain brake that can be activated either by inertial force or manually.
3. Automatic oil supply for lubrication of the cutting set (manual adjustment is not provided).
4. Primer is a pump that pumps fuel for cold engine starting.

In addition, this model has a power of 1.3 kW, a tire length of 40 cm, crankcase and fuel tank volumes of 210 ml and 360 ml, respectively, and a tool weight of 4.7 kg.

Poulan 1950

This tool has an average price. Poulan 1950 is popular among people who are just starting to work with gasoline saws, and among professionals who have been working with wood for a long time.

Features of the Poulan 1950 saw:

1. Characterized by good structural balancing.
2. High quality saw set. The bar length is 40 cm, the chain pitch is 3/8 inch.
3. Adjusting the oil supply for chain lubrication. The amount of lubricant supplied corresponds to the load of the gasoline engine.
4. Easy to clean nylon filter.
5. The presence of a primer that makes it easier to start a cold engine.

Owner reviews of the Poulan 2150 chain saw

All owners leave extremely positive reviews and comments both about the Poulan chainsaw itself and about its work. Very often they note high power and performance, small dimensions and weight, ease of use and economical fluid consumption. The reviews do not contain any comments or complaints about the operation of the Poulan 2150 chainsaw.

Maxim, 31 years old, Moscow

“I use this Poulan saw purely at home, I bought it for personal purposes. For six years, she actively sawed dead wood, prepared firewood, trimmed both thick and thin branches, and even used it a little in construction. She worked perfectly for the entire period, not a single comment. During its entire service life, I replaced the drive sprocket and tire once. I change the saw chain as needed.”

Situations in which adjustment is necessary

New chainsaws are supplied by the manufacturer with already adjusted carburetors. This is called standard adjustment. But for the normal running-in process, it is necessary to reduce the maximum engine speed and adjust the carburetor. After break-in, the chainsaw needs fine tuning to achieve maximum engine efficiency.

If there is too much fuel in the mixture, engine parts are poorly lubricated and premature wear occurs. Also, a poor quality mixture can cause the engine to jam due to overheating (this is one of the reasons why the chainsaw will not start).

This is what a jammed, overheated piston looks like from a disassembled chainsaw with an incorrectly configured carburetor.

Adjustment is necessary when the engine does not idle, stalls, or does not develop full power. Carburetor adjustment should be carried out with clean air and fuel filters. We also recommend reading an interesting article that details the main reasons why a chainsaw starts and immediately stalls.

Chainsaw Poulan (Poulan): parameters and equipment

Chainsaws from the popular Poulan brand have proven themselves well when caring for gardens. They stand out for their reliability and good quality components. The durable engines of Poulan chainsaws can withstand significant loads in the form of intense work in difficult weather conditions. At the same time, the amount of fuel consumed by the engines does not increase even during longitudinal cutting of wood at extremely high temperatures.

Chainsaws from the popular Poulan brand have proven themselves well when caring for gardens. They stand out for their reliability and good quality components. The durable engines of Poulan chainsaws can withstand significant loads in the form of intense work in difficult weather conditions. At the same time, the amount of fuel consumed by the engines does not increase even during longitudinal cutting of wood at extremely high temperatures.

Operational and technical characteristics

Until recently, all instruments produced at the Nashville factory had only an English-language manual. However, today a detailed description, technical and operational characteristics in Russian appeared on the Internet. You can read more about these documents in electronic form here: Your browser does not support frames Download the instruction manual

More complete information with descriptions, technical and operational characteristics of the Poulan chainsaw model range can be found on the official website.

When purchasing a Poulan chainsaw, you receive in the basic configuration:

• Branded case for storing and transporting the instrument;
• Manual (English or multilingual), product passport and warranty card;
• Saw body with gasoline engine;
• Poulan guide bar;
• Protective cover for saw bar;
• Poulan branded chain (3/8″ pitch, the number of links depends on the specific model);
• Set of mounting tools.

Over its history, the company has launched several dozen models of chainsaws on the market. Some of them are long outdated and discontinued. Others remain relevant today and are in great demand all over the world. You can get acquainted with the most interesting and popular models in our review.