Ice drill from a Husqvarna chainsaw: how to make an attachment

Preparing for equipment assembly

To make a homemade ice auger from a chainsaw, you need to prepare all the materials and equipment required for the work. It is best to do this in advance so that during assembly you do not waste time searching for the missing part.

To work you will need:

• durable metal drill without damage or traces of corrosion;
• engine from a household chainsaw;
• gearbox - needed to transmit torque from the internal combustion engine of the saw to the drill;
• several solid steel pipes, from which the body will be made in the future;
• welding machine;
• machine for grinding metal surfaces;
• a screwdriver or drill with a set of attachments for working with metal.

The work may also require a stationary lathe. With its help, the chainsaw owner will be able to adjust any part used to the dimensions required for assembly.

Before assembling the chainsaw equipment, you also need a diagram. It should describe in detail the dimensions of the parts used, as well as the method of installing them into the chainsaw drill device.

After preparing the necessary equipment and studying the drawings, you can proceed directly to assembly.

Domestic chainsaws

Old Soviet-made chainsaws have proven themselves well in the manufacture of motor drills. They have undoubted advantages - decent power and low revs. In addition, they are rarely used for their intended purpose, so they can be tightly fixed to the frame.

Knowing the dimensions of the engine, it is not difficult to make a frame for it. The fuel supply handle is located on the top of the structure. It should be always at hand, as well as the emergency shutdown mechanism. It should be noted that if the Ural is used, its element design will require the very minimum of modifications.

True, there is also a minus here - the engine is quite high, so if the angler is short, it will be difficult for him to drill. Now regarding the transmission of torque to the gearbox. Some Kulibins suggest using a chain drive, but this is hardly a good option. In this case, it is better to use a specially machined shaft.

Connecting the gearbox and the screw part

This part of the operation is the easiest. Alternatively, these two elements can be connected using a metal pipe, which can be secured with a keyed or stud joint. In this case, the screw part can be easily replaced with another of the required diameter.

However, it is possible to improve the design. For these purposes, you will need to make another frame from a metal tube, onto which a vertical section of the tube is welded. Metal rings are also welded to the previously manufactured body, which must be tightly strung onto a vertical section of pipe.

Next, the entire device is put on the shank of the screw part. Drilling holes with such a product is much more efficient, but there is a fly in the ointment: firstly, the mass of the mechanism increases somewhat, and secondly, if the ice is thick, the pipe will become a hindrance.

The ice drill for a chainsaw is almost ready, however, it is worth considering one more factor - sometimes it is possible to transmit torque using a flexible shaft. In this case, it is necessary to pay close attention to its strength characteristics. In addition, the shaft must be placed in a protective casing.

And finally, we note that not only a chainsaw can be used to attach an engine to an ice auger, but also a lawn mower and trimmer. The only condition is that you must correctly calculate the gearbox parameters, as described above. You should not get carried away with powerful engines, as this will ultimately affect the weight of the entire product.

By the way, a motor drill can demonstrate good ice drilling with properly sharpened blades. You can read how to do this in the article “Sharpening ice drill knives from domestic and foreign manufacturers.” It is important to remember that the slightest mistake can only make the situation worse.

How to make an ice screw from a chainsaw with your own hands?

The chainsaw drill is assembled in several stages. Each of them needs to be treated carefully. Otherwise, there will be a risk of rapid breakdown of one of the important elements of the device.

How to choose a gearbox?

First you need to choose a gearbox for the chainsaw for the drill. When purchasing an item, you should take into account such important factors as the power of the chainsaw engine and the size of the drill. It must be remembered that the motors of most gasoline tools have high power. If during operation the chainsaw motor drill rotates at too high a speed, then it will be impossible to work with it. At the same time, if the gearbox transmits too low a rotational force to the output shaft being used, then there will be very little benefit from using a gasoline tool. For these reasons, it is necessary to make accurate calculations of the gearbox parameters.

In most cases, in addition to the gearbox, a power take-off shaft is installed on a chainsaw hole drill. It regulates the speed of rotation of the engine crankshaft without loss of power. This makes it possible to make the drill more efficient and reduce the amount of fuel consumed by the engine.

Self-manufacturing of the case

The chainsaw attachment for drilling ice must be equipped with a reliable housing. This element of the device will protect all internal parts of the equipment from mechanical damage, as well as dust, debris and moisture entering the structure. To make the body, you need to use metal pipes that have no traces of rust or other defects. The pipes will need to be bent into the shape of frames.

This is done in the following order:

1. To begin with, you will need to measure a piece from the first pipe, the length of which should be equal to the perimeter of the planned frame. The optimal length would be approximately 160 cm;
2. Then, cuts will need to be made on the surface of the prepared section, the depth of which should not exceed 1/3 of the radius of the pipe used. These cuts should be located where the segment bends. In order for the pipe to bend easily, 4–6 cuts must be made at each point of its bend at a distance of 5 mm from each other. If, when bending the pipe, it is not possible to obtain an even right angle, then the cuts made will need to be slightly ground off with a grinder;
3. After bending the section, all joints and corners will remain welded with a manual welding machine.

In the same order, you will need to make another frame, the perimeter of which should be approximately 40 cm. Then the two frames must be connected so that the distance between their planes is about 35 cm. When assembling the frame, you need to make sure that the pieces of metal pipes of approximately the same size.

The result should be a body with the shape of a quadrangular uniform truncated pyramid. Inside it you will need to securely fasten the engine from the chainsaw, as well as the gearbox and other elements of the drill.

Methods for installing a motor for a drill

The result of the previous actions was a previously removed chainsaw engine, as well as a reliable housing, inside of which the gearbox is located. The existing elements will need to be connected to each other. To do this, you need to consider a method for connecting them.

If in the future the motor will be used exclusively for drilling holes, then a chainsaw drill for earth or ice can be made as a one-piece structure. In this case, the used engine will not be removed, and its mounting will be more reliable.

If the motor will sometimes be removed to mount it back on the chainsaw, then its mount will need to be made removable. This option is more practical to use, but the engine mount will be less reliable in this case.

To make a removable mount, you need to make a large hole in the manufactured housing to fix the motor. Its diameter must be the same as the dimensions of the internal combustion engine used. Next, you will need to carefully consider the engine mount. It should be as reliable as possible and time-efficient. It is best to use several bolts and nuts to secure the motor. In this case, the owner of the drill will only need to unscrew the bolts, lift the housing cover and carefully remove the motor.

When planning the engine mounting, free access to containers for refilling fuel and engine oil should be provided. Also, the owner of the drill must have access to the valve, which is needed to regulate the pressure in the engine cylinder.

It is best to equip a fishing drill with an engine from an old chainsaw. This motor can be installed permanently and not removed throughout the entire life of the drill. A frame will be needed to mount the old engine. It should be located at the top of the equipment. When installing the engine on the frame, you will need to remove the neck for filling fuel and oil. An emergency switch must be installed in the same part of the device. This element is very important in cases where the drill will be used not only for ice, but also for land. An emergency switch will make it possible to turn off the equipment when the soil is too hard.

Most often, motors from Ural chainsaws are used to make drills. These internal combustion engines require minimal modifications. The only negative is that only people of average and tall height can work with these engines.

Self-mounting drill

The working attachment of a homemade drill must be securely fastened. There are several ways to do this. The first of them is to use a pipe on which the gearbox and the drill used are mounted. An important advantage of this method is that, if necessary, the damaged element can be quickly replaced.

The second method is more difficult to implement, but it will make it possible to drill not only in the vertical, but also in the horizontal direction. To do this, you need a frame made of a metal pipe. In the future, you will need to weld another piece of vertical pipe to the frame. Several metal rings also need to be welded to the finished body. There should be no gaps inside the rings. When installing the drill, the rings must be put on the vertical pipe. After this, you can start using the chainsaw drill.

There are two disadvantages to this method. The first of them is the increase in the weight of the equipment, and the second is the difficulties during operation due to the vertical pipe.

Source: tehnika4sad.ru

Let's start with the gearbox

The choice of gearbox must be approached very responsibly: you cannot just take the first one you come across. The chainsaw engine is very powerful, and its speed is high. If the drill starts rotating at such a speed, it will simply be impossible for it to work. And if the gearbox transmits too low a torque to the output shaft, then using a chainsaw will be useless, because the rotation speed will remain low. That is why it is necessary to accurately and accurately calculate the characteristics of a suitable gearbox.

You can try reading technical literature and making this calculation yourself. And then make your own gearbox. But if you don’t have the time or desire, then you should contact a professional engineer who will not only perform the calculations correctly, but also help you choose the appropriate gearbox.

DIY chainsaw ice drill

A motor drill, or, as it is also called, an ice drill, is a useful household unit that allows you to make holes in the soil for installing a pile foundation, or prepare holes in the ice for winter fishing. The inflated cost of modern motor drills does not allow everyone to purchase them. In this case, you can make an ice screw from a chainsaw. By following our instructions, you can make a reliable homemade unit, which in its characteristics will not be inferior to store-bought counterparts.

Chainsaw-winter transport

They managed to use a chainsaw as an engine for a homemade snowmobile. Here the design is much more complex than a sawmill. In this case, in addition to manufacturing the snowmobile frame, you will need to make a suspension with shock absorbers, and connect the gas and clutch controls to the steering wheel.

In addition, you will need to find the drawings (or design it yourself) according to which the snowmobile track will be made, and think about the transmission of torque from the chainsaw to the track. Such a snowmobile is equipped with a centrifugal clutch with a chain and a poly-V-belt (after all, the chainsaw does not have its own transmission). In order to increase traction, a gear with a diameter larger than the chainsaw drive sprocket (the so-called “traction gear”) is installed on the track drive shaft.

For the steering mechanism, as a rule, they take the steering wheel from a scooter and bicycle and easily modify it so that it turns the snowmobile skis. Such transport requires an engine with a power of at least five horsepower, so if you are making a snowmobile, then use a Ural chainsaw.

If we consider transport for the winter, then the design of a snowmobile is much simpler. In them, a large screw is attached directly to the shaft of the chainsaw mounted at the back, which is the propeller. True, the low power of the chainsaw limits the maneuverability of such sleds on ice on a river or a compacted road. For racing on snowy fields, you need an engine of at least 12 horsepower. The same restrictions do not allow you to add a backpack helicopter to homemade chainsaws. Unless you use two engines and the master manages to make them work in harmony.

Preparation of equipment and materials

Before making a drill from a chainsaw, you should carefully prepare the materials and tools necessary for the work. For materials you will need:

• A serviceable household chainsaw;
• Gearbox;
• Solid steel sheet, or plywood, 2 cm thick;
• Set of various fasteners;
• Metal tube;
• Steel pipe, diameter 15 cm;
• Metal tube, 25 cm long;
• Steel auger;
• Rubberized insulation for the handle.

To work on making a motor drill from a chainsaw, be sure to prepare the following tools:

• Head for 27;
• Screwdriver;
• Bulgarian;
• Electric jigsaw;
• Grinding machine;
• Welding machine;
• A set of nozzles for working with metal.

To create some parts for a motor drill from a chainsaw, you will need a lathe, so you need to agree in advance with a specialist in the manufacture of metal parts.

Muffler for STIHL chainsaw

The video shows the work of a calm with a homemade muffler, which actually reduces engine noise by more than 50% of the order.

How to make a homemade muffler. The operation of the engine is judged by the noise of the gases, and it went when 2 years ago I made a copy of the Yak-50, and the goal was not to get a quiet one. They made the auger 20 revolutions and put it in the muffler pipe. The sound did not become quieter, but only changed. Roared on one note, on the letter: Sh-Sh-Sh-Sh-Sh-Sh-Sh! Electric saws probably don’t roll, because... We’ve already bought a bunch of chainsaws, but it’s also expensive to buy an electric one. Bosch AKE 30 LI cordless chainsaw. Quiet muffler for chainsaw. How to make a chainsaw » similar videos how to make. Somehow it turned out that the saw was not so expensive on sale. Cordless chain saw CTS CS from OREGON. Silent operation without soot and wires. How to make a silencer for a 2-stroke engine with their own hands. Construction, repairs with your own hands. How to make a chainsaw work silently. Repairing a chainsaw with your own hands A chainsaw, even if one wants to, cannot be classified as a complex device. Nevertheless, repairing a chainsaw can take a lot of time. The “grinder” attachment on a chainsaw performs such operations as cutting metal and stone, grinding the surface, and others. While a dedicated engine is very expensive, a boat engine made from a chainsaw is an excellent budget solution. How to start a chainsaw - a couple of the most popular methods. Disassembling the PARTNER 352 chainsaw. Airplane made from a chainsaw. Test chainsaw muffler. How to make a band saw PART - 1. That’s where the idea came to me, to tell him how to make a muffler for a chainsaw with your own hands. If you are smart, the same Ural saw can be made to work much quieter and this will not affect its performance in any way. There is an idea - to adapt a muffler from a moped to a chainsaw. What do you think? Has anyone done this? Once I had to quietly kill a couple of oak trees. It took a long time with two handles, so we decided to modernize the calm. Homemade muffler for chainsaw. Video; market make a chainsaw quieter make it quieter like an air compressor hose with. Loaded. I use the chainsaw as a boat engine and therefore turned it off. In this video I will show how to simply upgrade a chainsaw, make it safe for hellish pranks. How to make a chainsaw as quiet as possible, and at the same time the loss of power is up to 15-20? So that trees can be felled without burning at night. It will be environmentally friendly, quiet and healthy! In my opinion, if your soul can’t stand the exhaust, there are two options: take a break and eat a Twix or switch to electric. Others: how to make a silent muffler for a chainsaw yourself, homemade products for a car with your own hands, a flame arrester instead of a catalyst for a Ford, a metal mesh in the forward flow, removing the catalyst for a VAZ 2114, a resonator for a Ford explorer 1991 How to make a chainsaw from To make such a saw, you will need: Lemonade Shikhan , rope, lighter, awl, stationery. knife. like How to make the exhaust quieter at idle so as not to disturb the neighbors) AstalavistA inD 3 year. make a chainsaw quieter - photo - Mastergrad Forum. Do-it-yourself quiet exhaust of VAZ 2109 - Raum Profi. How to make a quiet muffler for a chainsaw video - Mosstroyservice. Silent? How to make a chainsaw » similar videos on how to make a chainsaw. But how to make it yourself? How to make the exhaust quieter on a chainsaw? What can be done to make it work more quietly? Therefore, manufacturers around the world are creating more and more models with high power and light weight. Let's talk further in this article about how to make a muffler for a chainsaw. And what to do if you need a powerful and at the same time quiet model for working on a personal plot or when building a log house?

Important How many cubes of concrete are in a KamAZ mixer: how to correctly calculate the volume of a concrete mixer

Tips for choosing a gearbox for a motor drill

The design of a chainsaw motor drill necessarily includes a gearbox, which can be taken from unnecessary electrical equipment. When choosing a part, be sure to make sure that it has the necessary parameters, namely:

• The gearbox must have direct rotation;
• The gear ratio of the element should be from 1:25 to 1:50;
• The shank and shaft of the selected part must rotate in the same direction.

It is best to equip a chainsaw motor drill with a gearbox having a gear ratio of 1:30, in which the shaft serves as a continuation of the motor rotor.

Less popular models

Some models of Stihl chainsaws are in less demand. The lower sales volume is not due to marketing, but to the technical characteristics of these models.

1. The Stihl 023 chainsaw has low engine power. Used for work at home.
2. Shtil 350 is an improved analogue of outdated models. Thanks to improved technical characteristics, the cost has also increased. Shtil 350 is used in everyday life for short-term work with wood.
3. Model 210 is suitable for harvesting small volumes of wood. Low power and ease of use make the 210 model popular among owners of private homes.
4. Model 036 belongs to the professional chainsaws of the Stihl company. High endurance characterizes the device from the best side; the model can work for 8-10 hours in a row. The saw is equipped with a STIHL ElastoStart handle and automatic fuel control systems.
5. The 241 can perform many functions thanks to its M-Tronic automatic engine. The 241 chainsaw has a function that allows you to restore the parameters used when working with it the previous time. Economical and practical.
6. The model 25 saw belongs to the class of household chainsaws. If necessary, you can change the basic configuration to a more suitable one. Easily replace the standard Model 25 handle with the special ElastoStart handle. This is the smallest saw with an easy to install handle.
7. Shtil 200 is a high-tech cordless saw. It performs many automatic functions, including automatic chain lubrication. At the same time, it has a minimal noise level.
8. Shtil 140 belongs to the class of cordless saws with a wide range of applications. The 140 saw operates almost silently, and the systems for controlling the operation of the device operate in automatic mode. Mainly used for domestic needs, can be used for work inside buildings.
9. The Stihl 023 chain saw weighs 6.1 kg and has a power of 2 hp. A household saw, the design of which is designed to ensure maximum worker safety. Convenient handle placement, side chain tension, auto ignition and chain brake - everything is designed for convenient and safe work at home.
10. Chainsaw MS 600 is a professional device for felling large trees and sawing them. Power is 7 hp. The MS 600 has the disadvantage of a large weight of 7.5 kg. This weight is explained by the high-quality technical equipment of all device systems.

Chainsaw hole drill - how to make it at home

Before making a motor drill from a chainsaw, you should carefully study the drawings. The diagram will help you determine the correct procedure and avoid mistakes.

If you do not find plywood of the required thickness, then instead you can take two thinner sheets and glue them together. Having received a product of suitable thickness, mark it to make the required holes for fasteners. Using a drill, you will need to make 2 additional holes - one of them should be located opposite the sprocket of the chainsaw drill, and the second - next to the first - is intended for mounting the nuts.

The further procedure for making a motor drill from a chainsaw is as follows:

1. Make an indentation in the top of the plywood piece using a sander. After this, attach the gearbox to the treated area to find out where it is installed in the chainsaw drill. In this case, be sure to take into account the features of the household tool that is used to make the structure. If the saw device has a sprocket with 6 beams, then use a 27 mm gearbox;
2. Next, secure the gearbox, center it, and securely fasten it to the bottom of the plywood. Then attach a chainsaw to the top of the plywood. After this, start its engine and check the reliability of the design;
3. At the next stage, you need to attach an auger to a homemade ice auger made from a chainsaw. To do this, take a pipe with thick walls and attach it to the gearbox with two bolts. The auger is attached to the gearbox in a chainsaw drill using an adapter that acts as a shock absorber. It can be made from a 15-centimeter steel pipe onto which rings are welded. Next, process the adapter on a lathe;
4. To make it more convenient to work with a chainsaw motor drill, the unit must be equipped with handles. To make them, a curved steel pipe is taken, onto the edges of which rubber seals are placed. You can attach the handle to a chainsaw drill using self-tapping screws or other available fasteners;
5. Excess parts of plywood are cut off using a chainsaw motor drill, and the edges of the remaining sheet are processed with an electric jigsaw;
6. Next, the finished chainsaw motor drill should be equipped with cutting knives. To do this, cut the steel sheets and weld them to the pipe that was used as the auger. In this case, the steel sheets should bend around the screw in the form of a spiral. The edges of the sheets must be sharpened carefully.

Motor: removable or non-removable

So, there is a drill, a chainsaw engine and a gearbox in a strong and reliable case. Now they need to be connected to each other. And here the question arises: how will the engine be used?

If the engine will be used only for drilling, then the structure can be made monolithic: the engine will not be removed from the structure.

However, this decision seems somewhat strange. After all, you will probably need to use a chainsaw someday, which means you will have to return the engine to its place. Therefore, it is better to leave the ability to remove the engine from a homemade housing as needed.

In order to obtain this opportunity, you need to make holes in the housing to install the engine. The hole must match the dimensions of the chainsaw engine.

In addition, it is very important to consider a reliable fastening system. The engine mount should be strong, but it shouldn't be a horribly time consuming process to insert or remove the engine. Ideally, it should be like this: unscrew two or three nuts, lift the frame, pull out the motor (or insert the motor, lower the frame, screw in the nuts).

When making a design, you need to take into account not only the size of the chainsaw, but also the convenience of refueling and valve control to control the pressure in the engine.

Drill attachment for chainsaw - application features

Of course, making a motor drill from a chainsaw is a more exciting and budget-friendly procedure. However, if you don’t want to waste your time and effort, then you can purchase a ready-made attachment that can be installed on a household tool to make a hole in the ground or ice.

This kind of ready-made attachment for a chainsaw is significantly superior to a homemade ice drill, since it is made of steel, which is many times stronger than plywood. It is smaller in size and easier to transport. In addition, thanks to the use of factory sharpening technology, it is much less necessary to restore the dull blades of the purchased attachment.

Installing and using the ice auger attachment is quite simple. To do this, the bar and saw chain of the chainsaw are removed, and an auger with blades is mounted instead. After this, all you have to do is install the lower part of the motor drill over the place where you need to make a hole and start the unit’s motor.

Source: sadovij-instrument.ru

Malfunctions and their elimination

Failures caused by the operation of the device occur for two reasons: violations of operating conditions and limited service life of the chainsaw elements. As a rule, all repair operations are associated with blockages of certain components. The most labor-intensive process is engine restoration. Repairing it yourself without tools and knowledge will be problematic, but repairing the remaining components with your own hands should not be difficult.

Carburetor breakdowns

You can troubleshoot and repair the carburetor of the Shtil 180 chainsaw yourself. Malfunctions in the carburetor are associated with the electric motor. This manifests itself in the inability of the saw to reach high speeds or its spontaneous stopping.

Important Advantages and disadvantages of the German household chainsaw Shtil 180

Most often, this situation occurs due to a stuck valve in the injector unit. To check the injector, you will need to remove the carburetor and clear it of debris. The principle of operation of the valve is based on the passage of air in only one direction. If it blows in both directions, you will have to replace it.

Another reason for the chainsaw stopping at increased speeds may be disturbances in the air intake. If there is a suspicion of depressurization of the suction unit, then the easiest way is to replace the gaskets

When replacing gaskets, you should pay attention to the condition of the needle bearing, defects of which lead to the valve not allowing the fuel mixture to pass through. The piston and spring may also be to blame for improper suction; they are also visually inspected for wear and replaced if necessary.

Fuel supply system repair

Characteristic signs indicating a breakdown of the supply system is that fuel stops flowing into the cylinder. If this problem occurs, first of all you need to check the hose and the condition of the membrane. If everything is in order with these components, then the reasons are a clogged filter or breather.

If the filter is suspected of being clogged, the hose is pulled out and the stream of escaping fuel is visually inspected. If the stream is continuous and under pressure, then everything indicates a filter malfunction. You can try to clean it, but it is more advisable to replace it - especially since the manufacturer, with an average load on the device, recommends replacing it every four months. A clogged breather is indicated by a poor fuel flow. The breather is cleaned with a sharp needle.

In addition, a clogged air filter can also be the culprit. There is not enough air mixed into the fuel, so the fuel mixture becomes too rich and engine performance is disrupted. Troubleshooting occurs by removing the filter and washing it in water.

In case of fuel supply failures, you should also pay attention to the carburetor channels and the integrity of the membrane. https://www.youtube.com/embed/WS8-gHi-IKI

Checking the ignition system

This system will require checking first if the chainsaw stops starting. You will need to unscrew the spark plug and inspect it. If it is dry, then the fuel does not reach the cylinder. The spark plug is wiped dry, and then, turning off the fuel supply, the starter starts. This inclusion allows you to dry the combustion chamber and get rid of gasoline residues.

The resulting carbon deposits on the spark plug indicate an incorrect ratio of fuel to oil or their poor quality. Carbon deposits are removed by mechanical friction; a knife or needle is used as a tool.

It is imperative to make sure that a spark appears between the spark plug terminals. If there is no spark, then the spark plug is replaced with a new one. In addition, high-voltage wires are checked for integrity.

It is worth noting that for reliable operation of the Shtil chainsaw it is necessary to select high-quality fuel. In this case, its quantity must correspond to the manufacturer’s requirements. If you periodically service your chainsaw, you won’t have to wonder why it suddenly broke down.

Originally posted 2018-04-18 12:12:41.

Motorized earth drill made from a chainsaw and gearbox

Greetings to those who like to tinker, I propose for consideration a motorized earth drill, which can be made using a chainsaw. Whether this project makes sense or not is up to you to decide, it all depends on whether you can get the necessary materials and how much they will cost you. A gearbox with a ratio of 1X100 is used as the “heart” of the device; this gearbox is called Bonfiglioli VF49. You can buy it or use a similar one, in any case, a homemade one should cost you much less than if you buy a new earth drill.

The device is not difficult to assemble, the chainsaw does not change structurally in any way, it is just a kind of attachment for a chainsaw. Now you won't need to dig holes with a shovel to bury the posts; this can be done in a matter of minutes with the help of this homemade drill. If you are interested in the project, let's take a closer look at how to assemble a homemade product!

Materials and tools used by the author:

List of materials:

— hand-held earth drill; - chainsaw; — Bonfiglioli VF49 gearbox; - Sheet steel; - round timber.

List of tools:

- lathe; - drill; - taps for threading; - Bulgarian; - vice; - pendulum saw; — plasma cutter; — belt grinder; - screwdriver, wrenches.

Homemade manufacturing process:

Step one. Making an adapter

First, we need to make an adapter, with the help of which we will connect the drill gearbox to the chainsaw sprocket. To do this, the author removes the sprocket from the saw and traces it with a marker on thick sheet steel. Next, the marked area needs to be cut out; to do this, first drill a hole in the center. Well, then we cut out the rest using a jigsaw, and then files. As a result, the part should easily fit onto the chainsaw sprocket. We give it a round shape, cut off the excess, and then sand it using a belt sander.

Step four. Drill installation

We need to make an adapter for the reduction gearbox output; the author also turns it on a lathe. Well, then we install the part on the gearbox and put on the earth drill.

Additionally, the author installed knives made of chrome-vannadium steel on the drill so that it would penetrate the roots well and, in general, the drill would drill well.

Source: usamodelkina.ru

Types of ice drills, their features

Products may differ in the structure of the cutting element:

1. Spoon. It got its name because of the design of the knife - it is made in the form of a spoon. This type of drill is already outdated and is now practically out of production. It is characterized by simplicity, but requires a lot of effort when drilling;
2. Auger. The most common option today. There are quite a few modifications of the product, but the general structure is similar:
   • Rod (tube on which other parts are attached);

   Knives. Usually there are 2, but there may be more. They directly cut away layers of ice;

3. Spiral tape that is attached to the rod. Its task is to lift the chopped ice to the top.

The diameter varies from 7 to 25 centimeters, the configuration, number, thickness of the turns are also not the same;

4. Cylinder. No more common than a spoon. A small oval hole is cut, forming a cylinder. Then, using a rod, the cylinder is pushed under the ice.

The following classification:

• Mechanical. Various models, the common feature of which is manual rotation. This can be a small brace or a large two-handed drill;
• Motor drills. The screw comes complete with an internal combustion engine with a special nozzle and holder. The engine runs on a mixture of gasoline and oil. Used in northern latitudes. Expensive, but very powerful product;
• Electric drills. An auger drill with an electric motor powered by a battery allows you to avoid using your own forces to create a hole, while it operates almost silently, is much lighter than the previous version and is much cheaper.

What types of ice axes are there?

A drill for winter fishing is an irreplaceable thing. The speed of making holes will depend on its quality, size and drive. Most often, screw devices are used for these purposes. This is the most common type of drill. Both factory-made and self-made products use a rotary drive as a drive. It is suitable for drilling holes with a diameter of 100−115 mm. It will be difficult to make a hole with dimensions of 130-150 mm, since it will require much greater effort.

For such purposes, you can use an ice drill from a chainsaw. With this tool you can quickly drill a hole of any diameter with virtually no effort. Most often they are used on reservoirs with thick ice. Almost any fish will pass through a hole with a diameter of more than 130 mm.

To make a type of motor drill - a gas drill - for winter fishing with your own hands, a saw with a gasoline engine or a drive from a brush cutter is suitable. The device will be mobile and effective. Holes are drilled in a few seconds, regardless of the thickness of the ice.

Why is the Ural chainsaw used?

In terms of their reliability, level of performance and ease of maintenance, Ural chainsaws can give a head start to almost any modern chainsaw. The main components of this saw include a drive with a motor and the cutting bar itself, which were made quite well.

The key factors that allowed craftsmen to make miracles of design ideas from old and temporarily unnecessary Ural chainsaws include:

• quite powerful and high-torque engine;
• low weight and relative compactness of the engine;
• the ability to work for long periods of time under high loads and in a variety of conditions;
• a well-thought-out and high-quality design of the saw itself, for example, a clutch that prevents overload, as well as preventing breakage of the main components.

All this, combined with the versatility of the drive and ingenuity, allows craftsmen to independently create functional devices of various types.

This is interesting: TOP 8 most popular Russian brands of chainsaws: study with us

Types and characteristics of motor drills

For ice fishing, drills with manual and motor drives are used. Often they are made independently according to their height and choosing the direction of rotation. Making an ice screw with your own hands is difficult, but possible. This requires welding skills and will also require the help of a turner.

A self-made drill must meet the following characteristics:

• have little weight;
• be collapsible;
• be made of quality material;
• have a drive corresponding to the diameter of the screw.

When making an ice ax from a chainsaw with your own hands, the connection diagram between the engine and the auger is performed using a reduction gearbox. Most often, the mechanical part of a low-speed electric drill is used.

Making a homemade drill bit is not difficult. It consists of a brace with a pin, at the bottom of which a cutting tip, made in the form of a spatula or spoon, is welded. Only one side is sharpened depending on the direction of rotation of the tool. This drill for fishing in winter can drill into ice up to 30 cm thick.

Now this type of drill is unfairly forgotten and is almost never used. It is a ring with an outer diameter of 130 mm and an inner diameter of 80 mm. The cutting serrated edge selects ice only according to the shape of the ring, leaving an ice cylinder inside. The drill is centered by a triangular collar, which is located on the bottom of the working part. Thanks to the eccentrically located handle, the force is evenly distributed on both hands. During operation, there is no characteristic noise heard, like with other ice augers.

The disadvantage of the ring drill is the lack of a device for removing ice chips.

This simple design is a pipe, in the lower part of which 2 holding rods located on opposite sides of the rod are welded at an angle of 30°. The lower parts are connected to the pipe by plates in which holes are made for attaching cutting elements. Proper sharpening of the edges and their location should provide an optimal angle of attack for uniform distribution of forces when drilling a hole.

When ice fishing, fishing gear and poles can be extremely effective. If you prepare enough holes, you can hope for a good catch. However, it will not be easy to do this with a frame drill that does not have a device for removing sludge.

The most common type of ice screw. Not everyone can make it themselves. This requires appropriate skills. The drill consists of a rod made of a pipe to which an auger tape is welded. To make a homemade project, you will need to cut out several metal rings and bend them into blades. The parts are welded to the rod and sequentially connected to each other by welding.

Making knives is particularly difficult. This requires alloy steel. It is practically resistant to corrosion and has high strength. Parts from disc cultivators have proven themselves well.

The cutting head can be made removable or its parts can be welded to the pipe. The number of knives affects the drilling speed, but at the same time the applied effort increases. Proper sharpening of the cutting edge facilitates the drilling process.

The auger part of the ice auger is connected to the rotator or mechanical drive using an adapter, which simplifies disassembling the tool for transportation.

Simple homemade products

First, let's present options for simple homemade products based on a chainsaw engine.

The bearing assembly with the shaft will become the basis of the angle grinder design. A mandrel for cut circles is fixed on one edge. The V-belt drives the driven pulley at the other end. Depending on the brand, a homemade grinder is capable of cutting metal, stone, brick and other building materials.

The chainsaw drive is used to make a winch. The initial engine power determines the tractive effort of the homemade product. Installing an additional unit will help to significantly increase the performance characteristics of the device. Additionally, the mechanism is equipped with hooks, belts, a pull-out block and anchors.

Any craftsman who begins to understand mechanics can master the simple design of a motor cultivator. To make a homemade product, the chainsaw engine will need to be equipped with a transmission system in the form of two gears. This will transfer the driving force of the motor to the wheel. The working mechanism will begin to move. You won’t be able to plow a large field with a homemade product, but for cultivating a small area, the power of such a mechanism is sufficient.

A homemade chainsaw in the form of a pump for pumping water will be an excellent helper in the household. Among the possible areas of application of the mechanism:

• emergency water supply to a site or residential premises;
• watering the garden;
• pumping water from a flooded basement;
• drainage of reservoirs.

Using the same principle, with a few minor nuances, they create a homemade product in the form of a boat motor.

Boat engine

The design of a boat motor is quite primitive, but a homemade one from a chainsaw engine can save money on purchase. The absence of a transmission makes installation easier. To modernize the boat, you will need to ensure the connection between the chainsaw engine and the propeller. An adapter that transmits the torsion function will help complete the task. In order for the homemade design to work properly, mounting the chainsaw engine on the boat provides a slight slope to the water of the propeller shaft.

Comment! Among the main advantages of the homemade product are high power, providing decent speed of movement on the surface of the water, and economical consumption of fuel material. In an hour, a homemade chainsaw consumes 1 liter of gasoline at a speed of 20 km/h.

Motor drill

Before starting to make a motor drill, adjust the motor rotation speed. Maximum performance is not required for safe and comfortable operation. The gearbox, which is connected to the chainsaw engine, will help complete the task. The fastening system deserves special attention. Safe operation of the homemade product is possible provided that the parts fit tightly together.

Using a motorized drill as an ice ax for winter fishing requires you to take care of a high-quality drill and knives. Cheap parts will not withstand heavy loads and will quickly break. Another area of ​​application is preparing holes for installing screw piles and other stages of excavation work.

The video material demonstrates the operation of a homemade chainsaw.

Scooter

The chainsaw engine is used to create not only various tools and mechanisms, but also vehicles, where operation is due to the consumption of combustible fuel. One of the options for using a chainsaw is a scooter.

The design is based on a scooter with inflatable wheels and a hand brake system. The chainsaw motor is fixed on the rear platform of the scooter

It is important to make sure that the line of the rear wheel and the motor sprockets coincide

Adjustment of the energy supply level is provided by a manual accelerator. It is connected to the wires that are responsible for turning the chainsaw engine off and on. If such a system does not function well enough, a special pedal is installed.

Attention! To ensure that driving a vehicle does not cause injury, safety precautions are required. To do this, sprockets, open areas of the motor and other elements of the scooter are covered with fences

This will prevent damage to clothing and traumatic situations.

By analogy with a scooter, a bicycle can become the basis of a homemade chainsaw. In this case, the engine is fixed to the frame. To move, gears are used. On a mountain bike, the gearbox is responsible for controlling the speed.

The video demonstrates the engine capabilities of a miniature moped.

Do-it-yourself motorcycle ice drills - what options are there?

Fans of ice fishing have different attitudes towards small-scale mechanization when drilling holes. Some believe that a homemade ice drill made from a chainsaw makes it easier to make holes, while others believe that amateur fishing turns into profit.

Despite this, there are many craftsmen who make mechanically driven devices. There are many ways to make a hand drill. Brush cutters, saws and screwdrivers are used as drive motors.

Making a motorized ice drill from a trimmer with your own hands is easier than from a chainsaw, since installation of a gearbox is not required. The connection between the motor and the screw is carried out using a homemade adapter. If you have a power tool on your farm, making an ice screw yourself will be cheaper than buying an analogue in a store.

However, this tool will be effective if you go fishing with your own transport. Otherwise, an extra 10-15 kg in the hands or behind the back will create inconvenience for an unprepared fisherman. Any internal combustion engine is a source of increased danger. Follow safety requirements when refueling and working with gasoline engines.

Design and features of ice drills

Winter ice fishing is quite an exciting activity, and for it to be successful, you should be properly prepared for it. First of all, you need a reliable ice auger, the functionality of which can determine the mood of the entire fishing process.

At first, even a drill of the cheapest model can bring joy to the fisherman, as the fishing process is simplified. But the question just arises: how many holes can it be enough for, because it is known that a cheap instrument can fail at the most crucial moment.

Naturally, a high-quality model is not cheap, but still real ice fishing enthusiasts try to purchase just such a reliable tackle that could serve them for many years. Most often, avid fishermen prefer to choose titanium drills.

A fishing drill made of titanium is much more convenient than a metal one in that it is almost two times stronger and lighter than a metal one, which means that it is more convenient to move and work with it. However, due to its cost, not everyone can purchase such a convenient tool.

Today, almost every specialized hunting and fishing store sells all kinds of domestic and imported ice screws. There, if financial capabilities allow, you can also purchase motorized drilling equipment.

Design of hand drills

Almost all drills, even if they are made by different manufacturers, differ little from each other. True, some models have distinctive features. For example, the spiral design can be assembled from several elements or be solid. There may also be differences in the method of attaching the spiral, which can be welded to the drill axis partially or completely. In the first case, when drilling ice, the tool produces noise, which is undesirable in shallow water, as it can scare away the fish.

Based on everything, it should be remembered that if the body of the drill and its fastenings are made of low-quality materials or it has any design flaws, then even with high-quality knives, the drilling tool will quickly fail.

Type of knives

The main component of an ice drill is its blades. The higher the quality of steel used for them, the sharper and more reliable they are. Despite the fact that knives have a wide variety of different shapes, they can be divided into three types:

1. With flat edges.
2. Spherical.
3. Cutting heads.

But it is hardly worth singling out any design for its superiority over others. Each type of knife has its own advantages and certain disadvantages, and the main criterion for their reliability is the quality of the steel used for their manufacture.

For example, flat knives made of high-quality steel of domestic production have proven themselves well on dry soft ice at an air temperature of about ±0 degrees, but already at -10 C they are significantly inferior to hemispherical imported cutters.

Also, not everything is simple with the cutting heads, although they are considered universal, problems may arise with re-sharpening, since it is quite difficult to sharpen them yourself.

Screw auger

The purpose of the auger is to remove ice chips formed during drilling from the hole to the surface. It is mounted on the axial tube of the ice drill and has the shape of a spiral ribbon (Archimedes screw). At the moment there are a lot of screw modifications, but the general structure is almost the same:

1. The rod is made of a tube on which all the parts of the ice drill are attached.
2. Ice cutting knives. Usually they have from 2 to 4 or more cutting edges.
3. The spiral tape can have an outer diameter in the range of 70–250 mm, while the number of turns and the distance between them can be different for each model.

The depth of drilling depends on the length of the spiral auger, while almost all modifications of ice drills, without exception, are designed for drilling holes in ice 1 m thick. But drills from Finnish and Swedish manufacturers have longer augers, as they are designed for more severe climatic conditions.

Recently, more and more often on winter fishing you can find ice screws driven by rechargeable batteries. This makes drilling holes for fishing much easier, while drilling is carried out almost silently, which allows you to successfully use these tools in shallow water.

Making your own ice screw

Material for making knives

In conditions of mass production, it is not possible to use ultra-strong grades of steel. Both domestic and foreign analogues use a material with a hardness of about 60 units. according to Rockwell. These knives are good if the ice is free of sandy inclusions. The best option would be tool steel with 70-72 units. True, the manufacture and proper sharpening of knives will be expensive.

Manufacturing from scratch

The easiest way to make a homemade ice auger for winter fishing is in the form of a garden auger. A circular saw blade of the required diameter is used as knives that simultaneously act as an auger. It is sawed in half and welded to the drill rod at an angle that provides the best cut.

The saw teeth have pobedite surfacing, which protects the edges from breakage when drilling through ice with sand inclusions and at the boundary of the underwater part. Using an ice drill screwdriver will help increase productivity. The increased speed of rotation of the rod will allow you to make holes even with not very sharp knives.

Screwdriver with drill for ice fishing

Often fishermen use an ice screwdriver. In order to assemble a high-quality ice auger, you need to choose the right components of the tool.

First of all, let's talk about the screwdriver. You need a professional tool with a very good torque (at least 80 Newton). And you also need capacious batteries. Preferably two, or even more (3 amps).

What are the best batteries to take?

1. It is better to give preference to lithium-ion batteries. But such screwdrivers are, unfortunately, very expensive.
2. A nickel metal hydride battery will also work.

It is very important that the screwdriver has a handle. What is it for? Firstly, when drilling ice it is very convenient to hold onto it

Secondly, if the drill jams, it can twist the hand. And when you hold the handle with your other hand, it is almost impossible to twist the hand. You will create force in time and the screwdriver will not cause injury.

In order to drill ice with a screwdriver you need an adapter. There are quite a lot of them being produced now. They are produced industrially, and buying them is not a problem. On the one hand, they have a hexagon for a drill, and on the other, an adapter for a drill.

Now there are adapters on sale with one handle that rotates freely. In principle, this is not bad. Of course, this handle is not used for drilling. Because the handle from a drill is used.

But for a drill it serves as a very good fuse. If suddenly this entire structure falls out of the drill chuck, it will prevent the drill from falling under the ice.

It must be borne in mind that for a 60 drill and above, this handle no longer provides a guarantee that it will not go under the ice. You still need some kind of adaptation.

As for the diameter of the adapters, there are two standard diameters for drills:

• 18 mm;
• 22 mm.

Rules for caring for an ice auger

Homemade electric ice drills require careful handling. After fishing, the instrument must be cleared of ice, wiped and dried. Coat cutting surfaces with a thin layer of lubricant. To make it easier to unscrew the screws to replace the knives, the threads should be wrapped with plumber's tape. Charge the batteries to full capacity.

Before fishing, knives should be sharpened and burrs removed. The drill must be transported in a folded case. By properly caring for your tool, you can protect yourself from surprises while fishing.

Source: ribaku.info

The principle of designing a snowmobile based on a chainsaw engine

Using a gasoline saw motor, you can mount vehicles that can move not only on hard surfaces, but also on snow.

It is possible to build a chainsaw based on an engine, but here the design will be more complex. The frame of the mechanism must be equipped with a suspension with shock absorbers, and the device must also be equipped with a clutch.

An ordinary bicycle handlebar can serve as a control mechanism; it is only important to equip it for the movement of a snowmobile. In addition, it is important to carefully approach the provision of torque, since due to the absence of a gearbox, the vehicle will only be able to move thanks to a correctly mounted clutch

Which gearbox is suitable for assembly?

The chainsaw drill must be equipped with a suitable gearbox. Often, a mechanism from old unnecessary electrical equipment is used for this. The selected gearbox for a drill chainsaw must meet certain characteristics.

These include:

• ability for direct rotation;
• gear ratio in the ranges 1:25–1:50;
• both the shaft and the shank of the element must rotate continuously in one specific direction.

It is best to initially equip a homemade motor drill from a chainsaw with a gearbox that creates a gear ratio of 1:30. In this case, the shaft of the mechanism must be a direct continuation of the rotor of the gasoline engine.

Installation of the unit structure

Once assembled, the height of the structure will be barely 10 cm (including the body, protective screen, including the distance to the support plate). The distance between the axes of the studs in this case will be 32 millimeters with a height of 24.5, the center-to-center distance from the shaft to the first stud will be 54 millimeters. Considering that the weight of the entire structure (albeit without taking into account the tire) is quite suitable, a little more than 4.5 kg, for fastening you can choose a stud with a metric thread with a diameter of 8 mm and a thread pitch of 1 mm.

To secure the motor and shaft, you will need a channel. Armed with a grinder, a mount of the desired configuration is cut out of the workpiece, and then holes are drilled for the fasteners connecting this structure and the chainsaw itself.

When assembling, it is necessary to take into account sufficient distance between the front coupling bowl and the support frame. A gearbox borrowed from an angle grinder will be attached to the second side of the shaft.

The next stage of work will be the construction of the rotary unit. To do this, you will need a piece of tube with a diameter slightly larger than the shaft with a welded corner for fastening the guide, a hollow hexagonal guide, a metal rod of suitable diameter and a rectangular metal blank with holes in the ends for securing the rod, as well as a slot in the upper part for ease of work.

The edges of the cut “handle” in the workpiece must be thoroughly cleaned. A guide is attached to the corner by welding, and then using a rod the resulting structure is connected to a rectangular “handle”. The ends of the rod can be threaded for secure fastening; you can simply install them with a slight interference fit. Then the entire assembly is placed on the shaft and secured in a place convenient for control.

At the next step, you will have to adapt the gearbox shaft for the existing propeller. It is advisable, of course, to use this important part ready-made; it can be removed from the old motor. For those who are not looking for easy ways, the option of making a homemade product is possible. In the image and likeness of a factory-made screw, a mold is made into which the future screw is poured using epoxy glue and fiberglass. After some simple manipulations (grinding, painting), the screw is ready

However, it must be taken into account that the propeller will take on a significant load, and during manufacturing it is very important to correctly maintain all dimensions. Therefore, it is better to use a ready-made part.

After connecting the screw and the gearbox shaft using a pin, the final stage begins. Transmission oil is poured into the gearbox, the cover together with the installed shaft is secured using sealant. And then comes the final assembly of the entire structure. For ease of use, you can additionally mount the throttle handle.

Boat owners often use motors to make their boat as fast and maneuverable as possible. The cost of factory units is not affordable for everyone, so most users prefer to create a motor from a chainsaw for a boat on their own. It is worth noting that the upcoming intervention in the basic design is minimal, so the equipment will remain suitable for further use for its intended purpose.

Description

was founded 90 years ago by German engineer Andreas Stihl in the 1920s. At that time, Stihl was working in the German city of Stuttgart - he created a design bureau, the immediate field of activity of which included working with wood. Tree felling back then was done with the help of axes, and such work took a lot of effort from the workers.

The Stihl chainsaw first appeared in 1929. The flagship model weighed 46 kg. and was the prototype of modern light and powerful devices. More compact models were produced by Stihl in the 1950s, weighing 12 kg and producing 6 hp. The ranking of world leaders in gasoline and electric saws includes not only the stihl company, but also the husqvarna company. All owners of chainsaws know the quality of the products of two world leaders in gasoline and electric tools.

STIHL Products

Currently, cases of sale of counterfeits on the instrument market have become more frequent. The country producing counterfeits is China. Often, a buyer comes across a fake chainsaw, which is difficult to distinguish from the original one at first glance. How you can learn to distinguish a fake Shtil chainsaw from the original:

Chainsaw Stihl 310-MS

The modern range of Stihl products:

• chainsaws;
• electric saws;
• garden trimmers;
• brush cutters;
• lawnmowers;
• drills, as well as battery technology;
• motor drills, hand garden and country tools;
• equipment for workers and gardening, protective equipment;
• multi and combi systems for gardening;
• cleaning equipment and saws for concrete.

Let's start attaching the drill

Of course, like the engine, the drill must be firmly fixed. But it's much easier to do. To attach it, you can take a pipe and connect the gearbox and drill with such a pipe, and then fix these connections. The big advantage of this design is that the drill can be replaced if necessary (for example, you may need to drill a hole of a different size).

It is imperative to ensure the reliability of the drill and check that the completed design will be safe for the driller.

You can try to make an “advanced” drill, which will have the ability not only for horizontal, but also for vertical drilling. To do this, you need another frame (made of a metal pipe) with a welded piece of vertical pipe.

More metal rings need to be welded to the body, which was made first. This will allow you to make an ice auger from a watch the video - an ice auger from a chainsaw, reasons and how. These rings must fit onto the vertical pipe without gaps. Now the entire updated structure is put on the drill pipe. The engine from a chainsaw has become so widely used thanks to how to make a motor drill from. You can start drilling.

There are two advantages to such an “advanced” drill: firstly, vertical drilling becomes possible, and secondly, drilling becomes much more convenient. However, there are also two disadvantages: firstly, it becomes heavier, and secondly, when drilling very deep, the drill pipe will interfere.

You can get rid of the second disadvantage if you make a drill guide pipe from parts that slide out from one another. Of course, these parts should not have a gap, but they should move within each other. Yes, and the structure will become even heavier.

You can also make it so that you can drill at a given angle. But the need for such drilling arises so rarely that it is better not to think specifically about this problem.

Sometimes a flexible shaft can be used to transmit torque. But we must not forget that in order for such a shaft to be strong, capable of withstanding heavy loads, it needs to be in a protective shell.

And, of course, for the drill you can use not only the engine of a chainsaw, but also the engine of a lawn mower or trimmer. You just need to correctly calculate and select the gearbox. It is not necessary to use an overly powerful engine or a large-volume engine for a drill, as this will make the motor drill too heavy.

Chainsaws Shtil 180 - malfunctions and repairs

The simplicity of the Stihl MS 180 household chainsaw allows its owner to eliminate most of the tool’s malfunctions with his own hands. To successfully repair a model, you first need to determine the causes of the breakdown. The repair algorithm is different in each individual case and depends on the type of malfunction.

Why won't the Shtil 180 chainsaw start?

The reason for the Stihl model not starting, in this case, is that the spark plug is flooded.

To fix the problem, you will need to disassemble the upper part of the tool and unscrew the spark plug. If a thick layer of carbon deposits has formed on the candle, it will need to be cleaned and dried. After this, the clean spark plug can be screwed back in.

What to do if the spark plug on the Shtil 180 chainsaw floods?

If the tool is used frequently, one of its fuel pipes may be torn, which will lead to fuel spilling onto the spark plug and other parts of the saw.

If the fuel tube breaks or a hole forms in it, the owner of the tool will need to remove the damaged hose and replace it with a new one. In this case, the junction of the new hose with the factory fitting must be carefully treated with sealant.

Oil does not flow to the chain of the Shtil 180 chainsaw

One of the main causes of the problem in which oil is not supplied is a breakdown of the pump that supplies oil to the saw set. To fix the problem, you will need to remove the bar and chain, and also dismantle the side protective plastic cover. After this, the area under the housing will need to be cleaned and the pump replaced.

If the chain is not lubricated, the cause of the breakdown may also be a break in one or more oil tubes. In this case, you will need to remove the hoses and replace them.

Chainsaw Shtil 180 stalls when you press the gas

In this case, the cause must be sought in a dirty air or built-in fuel filter. Over time, they become unusable as dirt accumulates on them. To fix the problem, you will need to clean or completely replace the filter parts.

Another reason for this breakdown lies in an incorrectly configured carburetor. The owner will need to first clean the unit from accumulated dust and oil residues, and also adjust it according to the manufacturer’s instructions.

Stihl 180 saw stalls at idle speed - how to solve the problem?

In this case, the cause of the sudden breakdown must be sought in the tool’s ignition system. Often, due to mechanical shocks, the gap between the flywheel and the factory ignition coil is broken, which leads to breakdown of the entire system. In this case, you will need to disassemble the tool and check the distance between the elements.

To adjust the clearance, you need to loosen the flywheel. After this, you will need to insert a template between the flywheel and the ignition coil and begin screwing the bolts back in. As soon as the flywheel comes into contact with the template, screwing in the bolts must be stopped.

Chainsaw Stihl MS 180 is difficult to start when cold

First you need to make sure that the spark plug is not flooded with fuel. If a thick layer of carbon deposits has formed on it, then the fuel system will need to be inspected. It could lose its seal as a result of a broken hose or a broken fuel pump.

If the spark plugs are fine, then you will need to check the air filter. As a result of intensive use of the chainsaw, it could become clogged or become unusable. In this case, cleaning the filter or replacing it will help.

The third element that could fail is one or more compression rings. They cannot be repaired and will need to be replaced.