Monitoring the oil volume in the gearbox on GAZelle vehicles and replacing it

The domestic GAZelle car is a popular and in-demand mode of transport due to its favorable quality-price ratio. This type of vehicle is actively and widely used as commercial, cargo, civil transport, etc.

Like any other car, especially one designed for high loads and difficult operating conditions, the GAZelle needs regular and high-quality maintenance of components and assemblies. In addition to the engine, the transmission also requires increased attention.

In this article we will look at what kind of oil should be poured into the Gazelle gearbox, when the oil in the Gazelle gearbox needs to be changed, as well as how to change the transmission fluid.

Oil selection

The gearbox oil purchased for replacement must be of proper quality.
Factors to consider when choosing oil:

• instructions from the manufacturer regarding the characteristics of the lubricant for the gearbox of a specific vehicle modification;
• operating conditions of the vehicle;
• The volume of oil purchased must exceed what is poured into the box by at least 0.5-1 liter. This excess will be needed for possible addition of fluid during operation.

The climatic conditions in which the vehicle is operated plays a serious role when choosing a lubricant, since the degree of viscosity of the selected material depends on this.

In some cases, the manufacturer does not bother with recommendations regarding certain lubricant characteristics, but only indicates which standard the transmission fluid must meet. Most often this is SAE 75W.

The following oils can be recommended from proven products:

• Castrol 75W140;
• Mannol 75W80;
• TNK Magnum Trans Gipoid Super 75W90.

This is not a complete list, however, you will be quite satisfied with any of the listed products.

The characteristics of transmission fluid meeting the SAE 75W standard are improved thanks to mineral additives. Due to the fact that a change in the viscosity of such a lubricant occurs when the temperature drops to -45˚ C, it can be used even in the coldest regions.

This is interesting: A guide to removing the instrument panel on a GAZelle Business and a description of the icons - let’s look at it carefully

Shift algorithm

Before you start replacing the oil product, you need to warm up the vehicle. This will increase the fluidity of the gear lubricant that is already filled. Then you need to install the car on a ditch or overpass.

Now you know what the volume of oil should be in the Gazelle gearbox and how to properly pour fresh consumables. Do not delay the replacement procedure. The longer you drive with old lubricant, the more the gearbox parts wear out.

The performance of the transmission depends on the quality of the oil.

What kind of oil should I pour into a Gazelle box when replacing it myself and how to do it correctly? For normal operation of this vehicle, the transmission must be filled with a suitable lubricant that will not disrupt the operation of the mechanism.

Typical faults

The most common gearbox malfunctions are the following:

• speeds do not change; when switching, a sound similar to a metallic crunch occurs;
• difficult transition between gears;
• when the car is overloaded, the active gear “flies off”;
• “sticking” of one speed, impossibility of switching to neutral;
• noise from the gearbox while the car is moving;
• At idle, a noise is heard, but when the clutch is pressed, it disappears;
• leaking crankcases.

The causes of such breakdowns are most often faulty parts that need to be replaced. Here is a list of the most common causes of breakdowns:

• cracking occurs due to wear of single teeth, chipped gears;
• breakage of teeth in the gear block;
• constant friction of the shift forks;
• wear of shafts and bearings makes it impossible to change gears;
• seals are broken;
• the oil has run out or has become unusable.

Algorithm for checking and changing oil in Gazelle

Check the lubricant level of the Gazelle gearbox as follows:

• Clean the filler neck from dirt;
• Use a clean rag, wiping the crankcase locations adjacent to the breather with it;
• Turn the lid a certain number of times.

In cars of this modification, there are several ways to check the oil level. It is easy to verify whether there is a lot or a little of it in a car that has driven 20 kilometers before the control. To check, the car is driven onto an overpass so that the car is only in a horizontal position. There should be no slope. Wait until the oil drains from the walls into the crankcase.

Unscrew the plug and observe the channel. If it starts to flow in a thin stream, then this is a signal that the level in the crankcase is lower. In this case, a syringe is used. With its help, a lubricating fluid is added and observed again. If the leak stops, this means that the oil level is normal. Afterwards the plug is screwed in. The process lasts 20 minutes. Maybe more if the check is carried out not on an overpass, but on a car inspection hole dug with your own hands.

The procedure for oil “improvement” of the transmission unit will require the preparation of tools. A bucket for draining waste liquid will come in handy. Syringe for adding lubricant. A rag and a can of new lubricant.

Operating a vehicle with a critical level of lubricant is strictly prohibited. Normal gear shifting will be complicated, and subsequently the gearbox may fail. A low oil level can create air barriers (plugs), causing a shortage of lubricant for gears and bearings.

Experienced drivers are able to detect underfilling of oil fluid by the noise of the box. But in order to have such experience and professional flair, you need to spend many hours behind the steering wheel of a car.

Which oil to choose

It should be understood that it is strictly forbidden to pour any transmission oil into the box. Each gearbox needs to be filled with oil with certain technical characteristics specified by the factory. Manufacturer's recommendations can be found by turning the pages of the technical manual. It is clearly stated here which oil is best to fill in the Gazelle gearbox. It is recommended to choose oil brands that are marked with SAE 75W viscosity. Do not skimp on purchasing gearbox oil, because when the air temperature rises or falls, the transmission fluid can undergo significant changes, preventing the gearbox from rotating the crankshaft normally. Most car owners prefer to pour Castrol 75w-140 or Total 75W-80 transmission fluid into the Gazelle box. We also recommend that you choose this kind of oil.

About level control

The lubrication level of the unit is checked after every 20 thousand km. This must be done even when no visible leaks are detected. If the lubricant level drops for some reason, transmission oil is added to the gearbox housing.

The operating instructions for GAZelle cars do not indicate a specific volume of lubricant to add to the gearbox, since depending on the modification of the car, the amount of oil can be in the range of 1.2-1.6 liters. Therefore, we recommend purchasing liquid in a 2-liter canister; any excess will be useful for refilling.

Before you start checking the fluid level, you need to thoroughly clean the breather, its cover and the nearby surface of the gearbox housing, after which you should turn the plug several times. The amount of lubricant is located at the lower edge of the filler hole, so cleaning it from dirt is extremely necessary.

Let's take a closer look at the process of monitoring the oil level in the gearbox of a GAZelle car:

1. You only need to check the quantity when the gearbox is warm. To do this, it will be enough to drive 10–15 kilometers.
2. The machine should be installed on an overpass or inspection hole; even a slight tilt in the horizontal plane is unacceptable.
3. It is necessary to allow the lubricant to drain from the walls to the bottom of the crankcase. During this time, use a rag to thoroughly wipe the filler hole cover, which is also a control hole.
4. You need to unscrew the plug and observe the hole. If a thin stream of lubricant flows through it, this is not evidence of a normal oil level. Next, you need to add fluid to the gearbox using a syringe and check again.
5. Stopping the flow of lubricant after topping up will indicate a normal fluid level in the system.
6. You can now tighten the plug and continue operating the vehicle.

Important! You only need to add lubricant to the car’s gearbox of the same type that was previously filled.

It is unacceptable to operate the car with a low oil level in the gearbox of the Gazelle Next and other models. Since insufficient volume can cause air pockets, which will affect the amount of lubricating fluid supplied to the gears and bearings of the gearbox.

Drain and filler plugs

Which oil is better to choose?

In the gearbox of the above car, the transmission fluid does not change as often as in the engine. The manufacturer recommends that consumers change the fluid less frequently than once every 4-5 years or every 75 thousand km, whichever comes first. According to Gazelle car owners, it is better to replace the fluid every four years or more often, or once every 60 thousand kilometers. In practice, the fluid in the gearbox deteriorates and loses its properties more often, so experts recommend replacing the fluid more often than recommended during operation and undergoing many tests. And the gearbox itself very often suffers from this. This unit has a particularly difficult time when the car owner fills in a product that is of poor quality or does not meet the technical parameters.

So which oil is best to choose for your Gazelle? This question was probably asked by every happy owner of a Gazelle car. And not in vain, because the optimal operation of the unit depends on the properties and characteristics of the TM in the gearbox. Unfortunately, the car manufacturer does not give clear recommendations on which brand of TM should be filled. However, the instruction manual states that the fluid viscosity marking should be “SAE 75W”.

Gazelle car gearbox removed

When choosing a TM, several factors should be taken into account:

1. First of all, these are recommendations from the specialists of the automobile concern. You should not ignore the recommendations. If experts advise pouring a TM with certain properties, then it is better to buy a more expensive TM.
2. Even with a frozen TM, the car’s crankshaft will be able to turn the gearbox shaft, but the gearbox itself will definitely not be able to turn the axle, so the fluid must be resistant to negative temperatures.

In practice, most car enthusiasts fill their cars with “Total 75W-80”. The latter brand of fluid is the most common when purchasing for replacement. This TM is mineral and has the following technical characteristics:

• the viscosity indicator at an engine operating temperature of 100 degrees is 8 mm2/s;
• the viscosity indicator at an engine operating temperature of 40 degrees is 49 mm2/s;
• the density of the consumable material is 877 kg/m3 at a temperature of 15 degrees;
• the pour point of the liquid is -45 degrees Celsius ambient temperature;
• the ignition temperature of TM is 208 degrees.

Important Features

Domestic Gazelle cars are widespread in Russia and neighboring countries, so we will take a detailed look at which oil is best to pour into the Gazelle gearbox and how to do it correctly? These vehicles are used as cargo or passenger vehicles, so operating conditions can be quite harsh.

The technical regulations for the car say what kind of oil to pour into the Gazelle box, but many car owners neglect this. Also, some motorists simply do not have such technical documentation, since they buy vehicles on the used car markets. For such people, we have prepared this material, in which we will consider in detail the suitable oils for the Gazelle gearbox.

Many owners of domestically produced Gazelle cars note that it is better to replace the transmission fluid every 60 thousand kilometers. When operating a vehicle, the gearbox experiences quite high loads, which do not always correspond to those calculated by the automaker.

Choosing a lubricant

The smooth functioning of the gearbox, as well as the timing of replacement, largely depend on the quality and characteristics of the engine oil.

In the video from user Mechanic, you can learn more about choosing transmission fluid for a GAZelle car.

When choosing a lubricant for a GAZelle gearbox, you should take into account the following factors:

1. Recommendations of the machine manufacturer for lubricants, which require certain requirements. It is best to use more expensive and high-quality oils, since by saving money on lubricants, you can spend a lot on repairing the unit.
2. When choosing a brand of oil, it is necessary to take into account not only the operating conditions of the car (ambient temperature, road surface condition, total mileage), but also the manufacturer of the transmission fluid, as well as its reputation in the automotive market.
3. You should purchase a “transmission” that is approximately 1 liter more than what is required for replacement. It will be needed later when topping up, and you only need to add the oil that was filled in earlier.

When choosing an oil, a lot depends on the climate in which the car is operated. In areas with low air temperatures, a liquid of lower viscosity is poured for the winter than in the southern regions.

Important Characteristics and reviews of owners of German-Chinese chainsaws of the Gardenlux brand (Gardenlux)

Car service books do not always contain recommendations regarding lubricant. For example, the operating instructions for a car with a UMP engine do not give specific instructions on the choice of oil; only a viscosity that meets the SAE 75W standard is recommended.

The following brands of oil correspond to these indicators:

• Castrol 75W140;
• Magnum 75W80;
• Total 75W80;
• Manol 75W80.

Cummins gear oil has also proven itself to be good, and is poured even into the boxes of business-class cars.

The presence of mineral additives in lubricants that meet the SAE 75W standard improves their characteristics, including density and viscosity. Such oils harden at a temperature of about -45°C, which allows them to be used in almost all regions of the Russian Federation.

How much lubricant to pour, what is needed for a change

What is the volume of the Gazelle transmission? The manufacturer does not give an exact answer. According to the technical information, the volume of lubricant in the box varies, ranging from 1.2-1.6 liters. The exact quantity depends on the specific car model.

It is worth mentioning that the volume of the transmission depends on the number of gears, the size of the gears, and other factors. It's safe to say that a couple of liters of oil fluid will be enough.

In order to change the oil in the box with your own hands, you will need:

Replacement instructions

If the required volume of transmission oil for replacement has been prepared and the location for the operation has been selected, then you can change the “transmission” in the box.

Required Tools

To replace you should prepare:

• container for collecting “working off”;
• a syringe for pouring new lubricant;
• cleaning material;
• new oil to fill.

In some cases, flushing the gearbox housing will be necessary. This will be indicated by the presence of metal shavings on the drain plug magnet. Then you should additionally prepare approximately 1 liter of flushing oil.

In the video from the channel Gazelists of Ukraine you can watch about changing the lubricant in the Gazelle gearbox.

How much lubricant to pour and what is needed to change

The next question that you may have actually causes difficulties for many Gazelle owners, since the manufacturer itself is silent in the technical documentation and does not specify how much oil is poured into the gearbox. It is for this reason that some car owners decide to purchase a certain amount of oil at random from the Gazelle gearbox. Unfortunately, this is not a good practice, because during the replacement process there may be a shortage of transmission fluid, as a result of which you will not be able to successfully complete the process. It would also be unwise to purchase a large amount of oil in reserve, since in this case you will have to incur serious financial losses. Depending on the modification of the vehicle, you may need 1.6 - 1.8 liters of transmission fluid.

In particular, prepare:

• a set of keys;
• syringe for filling lubricant;
• acetone;
• rags;
• a container in which you can collect waste;
• diesel fuel or kerosene.

Now we will assume that you have successfully prepared for the upcoming procedure, so you can begin practical actions.

About the order of the operation

We found out how much oil is in a GAZelle box, let's talk about how to replace it. This operation is carried out only on a warmed-up car gearbox, as this allows the “working off” to be completely drained.

Next, the procedure will be as follows:

1. The machine is installed on an inspection pit or overpass. Stops are placed under the wheels.
2. Thoroughly clean the drain and filler caps from accumulated dirt.
3. Unscrew the drain plug, having previously placed a container under the crankcase to collect the “working off”.
4. Drain the grease; this will take about 20 minutes.
5. The drain plug is inspected for the presence of metal shavings. If it is noticed, you should flush the gearbox housing.
6. The cleaned cap is screwed back into place and the filler is unscrewed. Depending on the vehicle configuration, it can be located on either the left or right side of the gearbox.
7. Add the required amount of lubricant to the open filler hole using a syringe. Continue pouring until oil flows out of the hole.
8. The plug is wiped and replaced.

If you don’t have a syringe at hand, you can change the oil without it. In this case, new lubricant is poured through the hole for the gear shift lever. Dismantling it will not be difficult. To do this, remove the protection in the form of a cover, and then turn out the lever. The required volume of liquid must be poured into the resulting hole in the crankcase, observing its appearance in the control hole.

Hole for gear lever

Replacing the rocker spring

Firstly, I’ll warn you, it’s better not to do this, but to replace it with a complete house, they seem to cost around 1 thousand rubles. But the harsh Volgovods are not looking for easy ways. The reason why I came here was that the gearshift lever moved towards 1-2 gears much more easily, to the right, towards fifth gear. I thought it was the spring that was weak.

I drilled out the plug and picked it out:

I checked out the old spring and did not find any fundamental discrepancies:

Further, carefully examining the house, I realized that different forces are specified structurally, the springs are initially compressed differently:

Well, of course, I disassembled the wrong side that I had planned. When reassembling, the new plug did not want to come unraveled and the body did not want to open up. I had to counter it with stainless steel wire and cover it with glue:

How the box works

GAZelles are equipped with 4- or 5-speed manual transmissions. Components of the device:

• 2 aluminum crankcases connected by 100 bolts;
• speedometer drive gear;
• primary and secondary shafts connected to the cardan and crankshaft;
• an intermediate shaft on which the cut reverse and 1st stage teeth are located;
• pressed gear block;
• inertial synchronizers;
• reverse gear is provided by a gear block;
• clutch for engaging 3rd and 4th gears;
• system for blocking simultaneous launch of several speeds;
• spring-loaded balls for fastening different levels of the box;
• mechanism of the damper device of the lever and control elements.

The design of the unit allows for timely diagnosis of the first signs of malfunction to prevent more dangerous failures.

Specifications

Key characteristics of the gearbox of GAZelle cars:

• 4- or 5-speed transmission;
• 5 speeds - 1 reverse and 4 forward.

For the transmission, the following parameters can be noted:

• three-way lever located in the assembly;
• the mass of the part is 56 kg;
• oil tank capacity - 3 l;
• gear ratios for five stages - 6.55; 3.09; 1.71; 1; 7.77.
• The fourth stage in the gearbox is direct.

Basic models of the device assume the presence of synchronizers in the mechanism to ensure reliable operation.

Gear shift diagram

The gear scheme on the GAZelle is distinguished by the presence of a synchronizer. Moving the lever from the neutral position to the left side causes its lower part to move the shift rod and fork. This causes the first stage gear to move backward and come into contact with the first gear element located on the intermediate shaft. When the clutch is running, torque is transmitted through gears and intermediate elements to the secondary shaft.

The inclusion of the third speed is due to the movement of the lever from the neutral position, first to the right side, and then forward. Under the influence of the fork, the clutch begins to move backwards and the structure impacts the synchronizer. The torque follows in the direction of: the input shaft, the permanently meshed gears, the intermediate and secondary shaft of the gearbox.

To start the fourth speed, you will need to move the selector to the right and back relative to neutral. The forward movement of the clutch helps to engage the synchronizer locking ring with the input shaft. After balancing the speeds, gears are engaged. Reverse speed is started by moving the lever to the right after overcoming the resistance of the safety system.

The synchronizer is a mechanism in the form of a hub mounted on the secondary shaft of the box. The coupling moves along the splines located outside under the influence of the fork. Other key elements of the synchronizer:

• retaining springs;
• "blocking" parts;
• side bronze rings for locking the mechanism;

The work of the synchronizer is involved in engaging 3rd and 4th gears and is expressed in ensuring a smooth transition from one level to another.

How much oil to fill

Before changing the oil in the 5th mortar, it is necessary to check the current level. It is recommended to carry out such an action every 20,000 km. If there is enough oil in the gearbox, fluid is added to the crankcase.

The technical documentation does not contain data on the required amount of oil in the GAZelle box. The figure varies depending on the modification of the equipment, ranging from 1.2-1.6 liters. During work, the mixture is poured into the hole with a syringe until oil flows out of it.

GAZelle Next, GAZelle Business and other modifications of the car cannot be started with a low level of oil fluid. Small volume is the cause of air pockets, which have a negative impact on bearings and other elements of the gearbox.

Tough: how to break manual transmission gears, and what it entails

The gearbox is one of the most important components of a car, but, paradoxically, it is often one of the most ignored. The engine oil is changed every 10 thousand, they take care of the cleanliness of the oil filter, monitor the operating temperature, oil pressure... In a manual transmission, the oil sometimes lasts for hundreds of thousands of kilometers, and the style of gear shifting and clutch operation adds problems to the box. The result can be quite predictable - so a manual gearbox from a Skoda Octavia came to our workbench, from which, according to the owner, “some kind of crunching noise was heard” when engaging first gear.

Gearbox: why and how

We will not disassemble the device of a manual transmission in detail: we have already talked . However, let’s go over the top to understand the processes that influence our repairs.

And so, globally, a gearbox is needed in order to transmit torque and power from the engine in a variable speed range. To change this range, pairs of gears with different gear ratios are used - it is thanks to them that those one and a half thousand revolutions will “turn” into several dozen revolutions of the drive wheels with a simultaneous increase in torque. The principle is similar to a bicycle: start off on a small sprocket, accelerate to 40 km/h - and switch to the next pair of gears with a smaller gear ratio to go faster. There can be 4 or 5 such shifts - modern manual transmissions are usually five or six speed.

The transmission of torque to the gearbox occurs directly by the meshing of these same gears. Gears are located on shafts - there are two-shaft and three-shaft gearboxes. The former have a primary (drive) and secondary (driven) shaft, while the latter transmit torque from the primary shaft to the secondary through an additional, intermediate one. The gears located on the shafts are in constant mesh, but all pairs, except the one selected as working at a particular moment, rotate freely. To select a pair - that is, to engage one or another gear by rigidly connecting the gear and the driven shaft - they came up with a special coupling and called it a synchronizer - we will talk more about the design and problems of synchronizers in the next material. Operating the gear shift lever from the passenger compartment, you connect one or another gear to the driven shaft through the shift forks and synchronizers and finally transmit torque from the engine to it (and therefore to the wheels).

The more gearbox stages, the more often the oil should be changed

The practice of operating and maintaining cars of this Gazelle brand shows that the more often the driver switches gears, the more intensively the fluid poured into the gearbox becomes clogged. No matter how effective the lubricating film covers the gears rubbing against each other, abrasive contact is still created, filling the oil structure with microscopic metal shavings.

The atomic oil loses its original viscosity, darkens, and performs its intended function less effectively. The main thing here is not to lose vigilance, but to promptly add lubricating fluid to a specific level or replace the oil if it does not meet the standard parameters in terms of lubricating characteristics.

Changing the gearbox lubricant yourself

Before you start directly replacing the transmission oil in the Gazelle box, you will need to warm up the unit to make the oil fluid more fluid. Start the engine and let the Gazelle run for a few minutes. If you don’t want to just waste time and waste fuel resources, then take a ride in a car and solve some of your pressing problems. After this, drive the Gazelle into the hole and use a hexagon to unscrew the drain plug.

Oil will immediately begin to flow out of it, so make sure that you can immediately place a container into which the old oil will flow. This process will take about half an hour, you still won’t be able to speed it up, so find some other activity during this time so as not to get bored. After the waste has drained, inspect it carefully. If you notice traces of metal shavings in it, then you will need to resort to flushing the gearbox. There is nothing complicated in this procedure. Just screw on the drain plug and, on the contrary, unscrew the filler plug. Using a filler syringe, pour about one liter of oil and 300 g of diesel fuel into it; by the way, it can be replaced with kerosene.

Important Design and technical characteristics of the L-34 front loader

Next, start the engine, engage first gear and let the engine run for a few minutes. Don't forget to put something under the front wheels. After this, we repeat the draining procedure, which will last about fifteen minutes. We tighten the drain plug and pour new oil through the filler hole. To allow it to spread well throughout the unit, we recommend not just driving the car at idle, but driving it for a certain distance. At the end of the trip, check the transmission fluid level. If you suddenly find that the level has dropped, then simply add a small amount of oil.

So, we hope that the process of replacing transmission fluid will not cause any particular difficulties, even if you do everything yourself. Concentrate and strictly follow the recommendations, in this case you will definitely succeed.

Let's move on to replacing the fluid

First you need to clean the gearbox breather from dust and dirt using rags moistened with acetone. Then climb under the bottom and look for the unit on which the drain plug should be located. Use a 12mm hex to unscrew this bolt, having previously prepared a container for draining the transmission fluid and placing it under the drain hole. The oil from the Gazelle gearbox will drain for about 20 minutes, so be patient.

If the old oil is dark or there are metal shavings in it, we recommend flushing the unit. Tighten the drain plug after cleaning off any dirt. Find the filler plug on the side and use a hexagon to unscrew it.

Using an oil syringe, pour about a liter of fluid into the transmission. You can use motor or motor, and also add about 300 ml of kerosene or diesel fuel.

Tighten the filler plug and support the front wheels. Start the engine and change gears for a few minutes. Next, go under the bottom and unscrew the drain bolt again, substituting a suitable container for waste.

Wait 15 minutes for the washing liquid to drain completely. Clean the plug again and screw it into place with a hexagon. Unscrew the filler plug and use the same syringe to fill in new gear oil for the Gazelle gearbox. Fill with liquid until then. Until it starts to pour out of the hole, a total of at least 1.2 liters will enter.

Tighten the filler plug and go on a short trip to check the unit for leaks. After that, crawl under the bottom again and look for any leaks. Now you know what kind of oil to pour into the Gazelle gearbox and how much it is needed.

Often, car enthusiasts do not know what aspects need to be taken into account for the high-quality operation of the car, but many are aware that the level and quality of oils in the transmission is an important indicator, no matter how many trips you make.

The quality and durability of its operation depends on what oil fluids are used in the gearbox; if necessary, they need to be replaced.

It is in this regard that you should pay attention to how often the change is made and what the oil level is in the gearbox of your car. This parameter is important for any model of any manufacturer, including the Gazelle car. Pay attention to what TM you are pouring into the machine box and whether you are carrying out the entire process of replacing raw materials correctly. The liquid must be poured according to the rules.

In order to be sure of the correct operation of the engine, you need to always have the fluid inside the gearbox in the right quantity and monitor its quality. If you notice that your car has started to malfunction, you should thoroughly check the presence and quantities of all fluids inside it. If after checking it turns out that the transmission oil (abbreviated as TM) is in short supply, then you need to replace it. No one can do this better than a specialist in a car service center, but, in fact, every motorist is able to carry out this work independently, at home, because he knows how to pour liquid into the hole.

Rules for replacing gearbox lubricant

How to change and fill oil in a Gazelle box

Before starting work, prepare the required amount of oil in the Gazelle gearbox 5 tbsp, rags, a container for draining the treatment, keys with different heads. It is convenient to follow the video or regular instructions. Experienced drivers do not have any problems; for beginners, it is better to work according to the manual first; later, when your hand is full, you can do everything out of habit without strict guidance.

Changing the oil in a Gazelle Business box

Business is the most popular modification; it does not present any difficulties in maintenance. First, use a wrench to unscrew the bolts on the pallet. Then remove all the fasteners that hold the structure in place.

You need to move around the perimeter, performing all actions as carefully as possible

The next step is to dismantle the filter. If it is in order, it is enough to wash it and install a new element. The lubricant must drain, the process takes time, the main thing is to wait and not rush. Afterwards you will need to return the components to their place, and replace all the old thinned gaskets.

Before servicing the modification, Business prepares a complete standard set of tools

The work can be considered complete, but before driving it is worth checking the level in the system when cold and warm. Probably, after the gearbox warms up, there will not be enough lubricant, then top up.

Changing the oil in the Gazelle Next gearbox

The sequence of actions for servicing the Next gearbox must be followed:

Use a wrench or other tool to unscrew all the pallet bolts, proceed carefully so as not to damage anything. Remove fasteners around the perimeter. Unscrew the filter, rinse thoroughly, and if possible or necessary, install a new one. Give the grease time to drain - usually this takes up to 20 minutes. Return all parts to their place, replace rubber elements with new ones.

The work is completed, all that remains is to test the level. It is optimal to do this in two ways - before the engine warms up and after.

Changing the oil in the Gazelle Next Cummins gearbox

When the tools and materials are ready, take the keys and use them to unscrew all the bolts of the pallet. The fasteners are removed carefully and moved around the perimeter. The filter element is ideally replaced, at least washed and returned to its place.

The liquid drains for about 15-30 minutes. You need to let the lubricant flow out, estimate the volume, and then pour the same amount into the system. Afterwards, all working parts are returned to their place.

Important! At each regular maintenance, the gaskets are inspected - they need to be replaced.

Done - all that remains is to test the level and adjust it if necessary. Additional checks are required, since after the replacement is completed, adjustments are made in at least half of the cases.

During disassembly, all parts are washed and returned to their place.

Changing the oil in the box of Gazelle 3302

The last popular modification on the list is 3302. Use a wrench to unscrew the pallet bolts to carefully remove the structure

Sudden movements and jerks should be avoided - act with extreme caution. After removing the fastenings, they move around the perimeter as accurately as possible

The filter is replaced or washed, and the composition is allowed to flow out quietly. All suspicious, worn-out elements are replaced with new ones. At the end, they test the level, warm up the gearbox and check the amount of lubricant again.

There is no way to speed up the process of liquid leakage, you need to wait

What will be required for replacement?

Before changing the transmission oil in a Gazelle, you must prepare all the necessary tools and accessories, including:

• hexagon 12;
• syringe for pouring oil;
• rags;
• new oil for the Gazelle gearbox in a volume of 2 liters;
• acetone;
• container for draining old oil;
• 300 g kerosene.

Prepare a place to change the oil in the Gazelle gearbox - this could be a pit, a lift or an overpass.

When to change the oil in a GAZelle box and which gearbox oil to choose

So, as you know, the Gazelle has a seriously modified manual transmission from a Volga car. Considering that the Gazelle is a truck, while the Volga is a passenger car, without proper care, the gearbox on a Gazelle under load will quickly fail. Usually by 80 thousand km a gearbox hum appears, gears fall out, etc.

For this reason, high-quality oil is necessary, as well as regular oil changes at certain intervals. The oil change interval in the GAZelle box at the factory is 50 thousand km. mileage, however, practical operation shows that it is better to change the oil in a gazelle box every 25-30 thousand km. mileage. Only in the case of high-quality synthetics can the interval be increased to 40 thousand km. (taking into account that the operating conditions are gentle).

Having decided on the intervals, now let's look at which oil to choose for the GAZelle box. At the factory, a cheap version of TAD17 is poured into the gearbox. Such a lubricant can only be considered a break-in lubricant, that is, it is better to change it after 500-1 thousand km.

The manufacturer indicates that GL-4 oil with a viscosity of 75W-90 should be poured into this gearbox. You can also fill in GL-5 with this viscosity, but in this case problems with synchronizers may arise.

In practice, you should abandon the use of cheap mineral oils in favor of semi-synthetics or synthetics. First of all, mineral water gets stuck in winter, gears are difficult to engage before warming up, wear increases, and fuel consumption increases. It is optimal to choose high-quality semi-synthetics.

To understand how much oil is in a GAZelle box and how much it needs to be filled, it is not enough just to study the manual. The manual says 2 liters. However, in practice one should not exclude casting defects, different versions of the gearbox, etc.

It turns out that the volume of oil in a particular box can be either 1.2 or up to 1.5 liters. This means that for replacement you should immediately purchase 2 liters, since underfilling is a serious problem and will quickly damage the gearbox. Oil must be filled strictly according to the level of the oil filler plug.

This is interesting: Technical characteristics and maintenance of GAZelle Next (Next) of various modifications: we analyze it carefully

Maintenance questions for GAZ gearboxes

Servicing the gearbox of GAZ vehicles comes down to the following work:

• Changing transmission oil (at intervals of 40-60 thousand km, depending on the operating conditions of the vehicle);
• Inspect the box for oil leaks;
• Checking the connection of the crankcase halves;
• Checking the reliability of installation of the box and its individual parts.

Particular attention should be paid to changing the oil. In the type of boxes under consideration, transmission oil with a viscosity of SAE 75W-90 or 85W-90 (depending on climatic conditions) is filled in an amount of only 1.2 liters. The oil is drained immediately after stopping the engine; if the oil is excessively contaminated, it is recommended to additionally rinse the box (you can use a different oil).

During maintenance, the general condition of the gearbox is also checked, and if faults are detected, repairs are carried out. It should be remembered that the primary and intermediate shafts of the boxes can only be replaced as an assembly, and the secondary shaft can be repaired by replacing individual gears or bearings. Any damage to the crankcase requires its complete replacement.

With regular maintenance, the use of recommended oils and high-quality spare parts, all gearboxes of Volga, GAZelle and Sobol cars will reliably perform their functions for many years.

Which oil is better to choose?

In the gearbox of the above car, the transmission fluid does not change as often as in the engine. The manufacturer recommends that consumers change the fluid less frequently than once every 4-5 years or every 75 thousand km, whichever comes first. According to Gazelle car owners, it is better to replace the fluid every four years or more often, or once every 60 thousand kilometers. In practice, the fluid in the gearbox deteriorates and loses its properties more often, so experts recommend replacing the fluid more often than recommended during operation and undergoing many tests. And the gearbox itself very often suffers from this. This unit has a particularly difficult time when the car owner fills in a product that is of poor quality or does not meet the technical parameters.

So which oil is best to choose for your Gazelle? This question was probably asked by every happy owner of a Gazelle car. And not in vain, because the optimal operation of the unit depends on the properties and characteristics of the TM in the gearbox. Unfortunately, the car manufacturer does not give clear recommendations on which brand of TM should be filled. However, the instruction manual states that the fluid viscosity marking should be “SAE 75W”.

Important The principle of operation and the difference between a crane beam and a hoist

Gazelle car gearbox removed

When choosing a TM, several factors should be taken into account:

1. First of all, these are recommendations from the specialists of the automobile concern. You should not ignore the recommendations. If experts advise pouring a TM with certain properties, then it is better to buy a more expensive TM.
2. Even with a frozen TM, the car’s crankshaft will be able to turn the gearbox shaft, but the gearbox itself will definitely not be able to turn the axle, so the fluid must be resistant to negative temperatures.

In practice, most car enthusiasts fill their cars with “Total 75W-80”. The latter brand of fluid is the most common when purchasing for replacement. This TM is mineral and has the following technical characteristics:

• the viscosity indicator at an engine operating temperature of 100 degrees is 8 mm2/s;
• the viscosity indicator at an engine operating temperature of 40 degrees is 49 mm2/s;
• the density of the consumable material is 877 kg/m3 at a temperature of 15 degrees;
• the pour point of the liquid is -45 degrees Celsius ambient temperature;
• the ignition temperature of TM is 208 degrees.

Which TM is most suitable for your car?

Different transmission oils are recommended for different car models; for example, for the models, manufacturers have selected the best raw materials with a viscosity level of “SAE 75W”. This means that before purchasing a TM, you must inspect the packaging and, having found the viscosity value, select a liquid with a viscosity of “SAE 75W”. Thanks to its viscosity, it is also easy to pour inside.

Also, any motorist should know that there is nothing more correct than the recommendations of the manufacturer’s specialists. Therefore, when purchasing TMs, you should not neglect them. If you see that the oil fluid is not suitable for your car model, then it is better to buy a suitable one, even if it is more expensive than the first one. You should know that when the TM hardens, then the gearbox of your car will not be able to turn its axle, even though the crankshaft will be able to work. Liquids can only harden at very low temperatures, so when selecting liquids for your car, take into account the minimum temperatures of your climate zone. Only high-quality raw materials should be poured into the car.

Make sure that the transmission raw materials are suitable for your vehicle.

The Castrol brand, such as “75w-140,” as well as the Total brand, “75W-80,” are perfect for your Gazelle’s gearbox. Due to the content of mineral substances in TM, it has excellent technical characteristics. For example, the viscosity index is very high, which will increase the duration of possible operation of your car’s gearbox. The quality of the density of the source materials is also very high, and the solidification temperature of the TM is about minus 45 degrees Celsius. This means that your car will be able to operate all year round throughout the Russian Federation. Also, raw materials with mineral components do not have a high ignition temperature - about 200 degrees.

How many TMs do you need to purchase to replace the gearbox of your Gazelle?

Basic rules for changing gearbox lubricant

Since Gazelle manufacturers often indicate how much can fit in a gearbox is not accurate, many car enthusiasts who do not have extensive driving experience do not understand how many TMs need to be purchased for a car’s gearbox. The capacity of the Gazelle's gearbox ranges from 1.2 liters to 1.6. The value usually depends on the model and its modification. But sometimes it happens that even one version of a car has different values ​​for this characteristic. Therefore, the total volume of oil fluid required may vary.

Fluctuations in volumes in a gearbox depend on many parameters, for example, the number of speeds of your model, the size of the gears inside the box and other important factors. If you take into account all the opinions of car enthusiasts and experts, then feel free to purchase at least two liters of TM. If your business depends on the performance of your car, then you should not skimp on oil fluids.

Assembly of the unit

This manipulation is performed in reverse order. After the necessary elements have been repaired or replaced, the shafts are simultaneously installed. To do this, it is advisable to connect them together with twine. Before starting assembly, you need to carefully inspect the crankcase for cracks, rust or other deformations.

First, all parts should be soaked in kerosene, any cracks and nicks should be sanded, all defective elements should be replaced, and lubricated with special oil. The crankcase fasteners must be treated with sealant, and the existing gaskets must be replaced. Experts recommend replacing bearings every 80-100 thousand kilometers.

Disassembling the Gazelle box and installing it requires attention and accuracy. The unit is mounted on the car by installing the assembled gearbox in the reverse order of removal. It is first necessary to lubricate the splines, and when installing the cardan, make sure that the marks match. After installation, you need to pour the required amount of oil into the crankcase and check the operation of the repaired unit.

About the consequences of untimely replacement

During the operation of the machine, transmission oils lose their qualities:

• the extreme pressure properties of the oil are reduced;
• lubricity deteriorates;
• the viscosity of the liquid decreases.

As a result, gearbox parts such as gears, bearings, and synchronizers may fail. And the cost of restoring them will be several times higher than the price of transmission oil and consumables.

The domestic GAZelle car is a popular and in-demand mode of transport due to its favorable quality-price ratio. This type of vehicle is actively and widely used as commercial, cargo, civil transport, etc.

Like any other car, especially one designed for high loads and difficult operating conditions, the GAZelle needs regular and high-quality maintenance of components and assemblies. In addition to the engine, the transmission also requires increased attention.

In this article we will look at what kind of oil should be poured into the Gazelle gearbox, when the oil in the Gazelle gearbox needs to be changed, as well as how to change the transmission fluid.

Read in this article

Features of the GAZelle gearbox: design and repair

The gearbox is a component of the transmission. It changes the gear ratio and torque transmitted from the engine to the vehicle's drive wheels. The gearbox has a very impressive service life and is capable of functioning flawlessly throughout the entire life of the vehicle. But this requires timely and high-quality checkpoint maintenance.

Today we will disassemble the gearbox of a Gazelle car. Let's add oil. To do this you will need a 12mm hexagon. If chips are found on the plug, it means there is wear in the gearbox.

The manufacturer recommends filling 1.2 liters. oil into the gearbox, but we recommend pouring at least 1.5 liters to avoid “oil starvation” in fifth gear during overload.

We disassemble the gearbox. For convenience, clamp it in a vice with the shank down, at an angle.

We unscrew all the bolts with a 12 mm socket, starting from the front flange and the input shaft, then the gearshift lever cover. It is more convenient to unscrew the bolts connecting the box body using a head with a “cardan”.

Using a 13mm socket, unscrew the bolts securing the reverse gear.

Remove the input shaft flange and clean off the remaining gasket and sealant on the housing.

Next, you need to remove the retaining ring, otherwise you will not be able to halve the box.

Remove the top half of the housing.

Unscrew the forks. Use pliers to remove the gear shift rod.

Be careful, the bearings may fall out. The outer rods are removed first, then the central one. It has an additional fixation rod.

If the rod is worn out, only the working part must be replaced. It is not advisable to completely change the stem.

We remove the forks and check the wear of the “crackers” - if they are good, we leave them.

The following operation must be carried out with an assistant. Use a pair of narrow-nose pliers to press the stopper and hold it, lifting the gear block until it disengages from the clutch.

We take out the gear block and begin an inspection; if chips are found on the gears, they need to be replaced.

When disassembling the “box”, we recommend replacing the input shaft seals and shank seals.

Remove the input shaft. Inside the shaft there are 14 rollers that spin on the shaft. To replace the bearing, you must remove the retaining ring.

Since the bearing is seated on the shaft, it must be knocked out. All other transmissions are analyzed by analogy. The retaining ring is removed, the gears are removed, and an inspection is carried out for chips.

After completion of the repair, assembly is carried out in the reverse order.

Source

Gazelle gearbox repair, diagnostics, replacement of gearbox bearings

And a little about the author’s secrets

My life is not only connected with cars, but with repairs and maintenance. But I also have hobbies like all men. My hobby is fishing.

I started a personal blog in which I share my experience. I try a lot of things, different methods and methods to increase my catch. If interested, you can read it. Nothing extra, just my personal experience.

Attention, TODAY only!

For high-quality protection against friction and damage to rubbing parts in the gearbox of a Gazelle car, it is necessary to control the level of lubricant in it. Therefore, you need to know how to determine how much oil is in the Gazelle box and what lubricant should be poured into the gear shift device.

[Hide]

Table: malfunctions of the Gazelle box according to the nature of the noise

Now you know how to remove and rebuild the Gazelle gearbox yourself.

Modernization

The unit is equipped with a microprocessor system for controlling the operation of the injection of fuel mixture and the accounting ignition system. The knock and oxygen sensors of the 4216 engine directly affect the operation of the all-encompassing electronic control accounting system and the unit as a result. To configure economic features and increase competitiveness, the following design additions were made to the power plant:

• To increase performance characteristics, the compression ratio in the cylinders was increased.
• To reduce oil consumption, the crankcase gas exhaust system was modernized.
• The reliability of the motor is ensured by the introduction of improved parts and materials.

Along with this, the unit has not changed in terms of overall characteristics and standard features (working volume - 5.89 liters, piston stroke, cylinder size).

For the first time, the GAZ-4216 engine began to be equipped with imported parts, which only increased the quality of work and durability in operation. The unit was equipped with spark plugs and fuel injectors made by Siemens, in addition to a throttle position sensor made by Bosch in Germany.