Truck crane KS-65713-1: review and technical specifications


Galician KS-65713-1

Specifications

Parameter

Index
ManufacturerJSC "Galich Truck Crane Plant"
Basic chassisKamAZ-65201
Wheel formula8x4
EngineKamAZ-740
Engine power, kW (hp)360
Load capacity, t50
Load moment, tm160
Boom length, m11,5 — 34,1
Jib length, m9,1-15,1
Load lifting/lowering speed, m/min
— nominal3,6
- increased7,2
Landing speed, m/min0,15
Rotation speed, min-10,1 — 1,2
Travel speed, km/hup to 40
Length, mm13950
Width, mm2500
Height, mm3980
FIND OUT PRICE

The KS-65713-1 crane with a lifting capacity of 50 tons is mounted on a four-axle KamAZ-65201 chassis with a wheel arrangement of 8 x 4 x 4. The truck crane is designed to perform loading and unloading and construction and installation work at dispersed sites and can be used both in modern cities and and in conditions of remoteness from populated areas.

The crane installation is driven using axial piston hydraulic pumps. The crane mechanisms have an individual drive with independent control from hydraulic motors and hydraulic cylinders. The hydraulic system of the crane installation ensures smooth control of all mechanisms with a wide range of speed control for working operations. It is possible to simultaneously combine up to three work operations.

The assembly of booms of truck cranes of the KS-65713 series is carried out on a specialized high-tech line for the production of booms from TADANO. The metal structures of the boom are entirely manufactured in Germany using the most modern technologies using high-strength imported WELDOX steel. Other critical components of the crane installation and support frame are also made using high-strength steels. The length of the boom in the retracted position is 11.5 m, providing the crane with compactness and maneuverability when moving. In the fully extended state of all four sections, the length of the boom is 34.1 m, which ensures a wide working area and the highest height of cargo movement during operation. The ability to telescope a boom with a load on a hook allows the crane to perform special tasks: installing loads in hard-to-reach places, carrying them among mounted structures. For the convenience of working in cramped conditions, a mode for working with loads is provided with the installation of the crane on supports with the outrigger beams retracted. The maximum size of the support contour (7 x 7) is achieved through the use of an outrigger design with folding support beams. Thanks to this solution, the crane is able to carry out work with loads in a 360-degree circular zone and, as a result, the number of rearrangements when working on site is minimized.

Additional equipment of the boom with a telescopic jib with a total length of 15.1 m (9.1 m is the stationary part, and a telescopic part with a length of 6.0 m) with the possibility of installation at an angle of 0 and 30 degrees relative to the longitudinal axis of the boom expands the scope of use of the crane, the area of ​​its service area and the size of the sub-boom space. The use of additional removable counterweights with a total weight of 6.0 tons during operation makes it possible to significantly increase the load characteristics of the crane at medium and long ranges, which provides the best performance among similar cranes of this size group.

Installation of jib and additional counterweights into the working position is carried out without the use of additional lifting equipment and human resources. The gearbox of the mechanisms for lifting loads and turning the crane is of a planetary type with disc brakes, which meets modern requirements for load-lifting machines. Many crane components use imported components that do not require replacement or repair over the entire service life of the crane. An autonomous diesel heater is used to heat the crane operator's cabin.

Safe operation of the crane is ensured by a complex of instruments and devices, including a microprocessor load limiter with digital indication of operating parameters on the display in the driver’s cabin. The device automatically protects the crane from overload and capsizing, is equipped with a crane coordinate protection system necessary for working in cramped conditions, has a built-in telemetric memory unit (“black box”) and a crane protection module from dangerous voltage (MZON) for working near power lines.

Load height characteristics

Supply of self-propelled cranes Yurginets: KS-4361A, KS-4372B, KS-4372V, KS-5871.

The KS-65713-1 crane with a lifting capacity of 50 tons is mounted on a four-axle KamAZ-65201 chassis with a wheel arrangement of 8 x 4 x 4. The truck crane is designed to perform loading and unloading and construction and installation work at dispersed sites and can be used both in modern cities and and in conditions of remoteness from populated areas.

The crane installation is driven using axial piston hydraulic pumps. The crane mechanisms have an individual drive with independent control from hydraulic motors and hydraulic cylinders. The hydraulic system of the crane installation ensures smooth control of all mechanisms with a wide range of speed control for working operations. It is possible to simultaneously combine up to three work operations.

The assembly of booms of truck cranes of the KS-65713 series is carried out on a specialized high-tech line for the production of booms from TADANO. The metal structures of the boom are entirely manufactured in Germany using the most modern technologies using high-strength imported WELDOX steel. Other critical components of the crane installation and support frame are also made using high-strength steels. The length of the boom in the retracted position is 11.5 m, providing the crane with compactness and maneuverability when moving. In the fully extended state of all four sections, the length of the boom is 34.1 m, which ensures a wide working area and the highest height of cargo movement during operation. The ability to telescope the boom with a load on the hook allows the crane to perform special tasks:

install loads in hard-to-reach places, carry them among mounted structures. For the convenience of working in cramped conditions, a mode for working with loads is provided with the installation of the crane on supports with the outrigger beams retracted. The maximum size of the support contour (7 x 7!!!) is achieved through the use of outrigger structures with folding support beams. Thanks to this solution, the crane is able to carry out work with loads in a 360-degree circular zone and, as a result, the number of rearrangements when working on site is minimized.

Additional equipment of the boom with a telescopic jib with a total length of 15.1 m (9.1 m - the stationary part, and a telescopic part with a length of 6.0 m) with the possibility of installation at an angle of 0 and 30 degrees relative to the longitudinal axis of the boom expands the scope of use of the crane, the area of ​​its service area and the size of the sub-boom space.

The use of additional removable counterweights with a total weight of 6.0 tons during operation allows to significantly increase the load characteristics of the crane at medium and long ranges, which provides the best performance among similar cranes of this size group

Installation of jib and additional counterweights into the working position is carried out without the use of additional lifting equipment and human resources.

The gearbox of the mechanisms for lifting loads and turning the crane is of a planetary type with disc brakes, which meets modern requirements for load-lifting machines. Many crane components use imported components that do not require replacement or repair over the entire service life of the crane. An autonomous diesel heater is used to heat the crane operator's cabin.

Safe operation of the crane is ensured by a complex of instruments and devices, including a microprocessor load limiter with digital indication of operating parameters on the display in the driver’s cabin. The device automatically protects the crane from overload and capsizing, is equipped with a crane coordinate protection system necessary for working in cramped conditions, has a built-in telemetric memory unit (“black box”) and a crane protection module from dangerous voltage (MZON) for working near power lines.

Specifications:

Maximum load moment, t.m 160 Maximum load capacity, t/reach, m 50/3.2 Boom length, m 11.5 – 34.1 Jib length, m 9.1; 15.1

Maximum hook lifting height, m ​​– with main boom 34.1 m 34.5 – with main boom 34.1 m and jib 15.1 m 50.4 Max. depth of lowering of the hook by the boom 11.5 m at a reach of 5.0 m, m 8.0 Weight of cargo at which extension of the boom sections is allowed, t 6.0

Load lifting and lowering speed, m/min – nominal (with a load weighing up to 50.0 t) 3.6 – increased (with a load weighing up to 10.0 t) 7.2 – maximum (pulley multiplex 1) 38.0 Speed load landing, m/min 0.15 Turning part rotation speed, rpm from 0.1 to 1.2 Crane travel speed under its own power, km/h up to 40

Size of the support contour along x across the chassis axis, m – with fully extended outriggers 7.2 x 7.0 – with retracted outrigger sections 6.73 x 4.63

Weight of the crane in transport position, t – with the main boom, without counterweights 36.5 – with the main boom, with counterweights 2t + 2t 40.5 – with the main boom, jib and one counterweight 40.1

The wheel arrangement of the base car is 8 x 4. The base car’s diesel engine is the KamAZ-740 model – power, hp 360

Operating temperature, degrees. From -40 to +40

Cargo characteristics:


Dimensions:

Dimensions of the crane in transport position, m, (length x width x height) 13.95 x 2.5 x 3.98

Additional characteristics of the truck crane

The KS truck crane with a lifting capacity of 30 tons has the following additional characteristics and capabilities:

  • the jib of the crane is 9.1–15.1 meters, that is, in a fully extended state, the length will be fifteen meters, and the angle of inclination of the equipment will be all measures up to thirty;
  • another load winch with a single block and counterweight can withstand 3.2 tons;
  • The equipment is also distinguished by an additional set of counterweights weighing six tons each, that is, two by three;
  • the wheel arrangement in cramped conditions is a characteristic feature of the crane, which allows it to work in any weather and other conditions. The KS-65713-1 “Galichanin” truck crane is an ideal example of large-sized equipment that can be used for heavy construction and installation work, since due to its good characteristics the machine can perform a wide range of work, regardless of the conditions.
  • View all 50 meter cranes

    Also, we work in: Balashikha, Voskresensk, Dolgoprudny, Domodedovo, Zhukovsky, Zaraysk, Istra, Klin, Lyubertsy, Mytishchi, Naro-Fominsk, Noginsk, Odintsovo, Pavlovsky Posad, Ramenskoye, Sergiev Posad, Serpukhov, Voskresensk, Khimki, Khotkovo, Shchelkovo, Elektrogorsk

    Rating
    ( 2 ratings, average 4.5 out of 5 )
    Did you like the article? Share with friends:
    For any suggestions regarding the site: [email protected]
    Для любых предложений по сайту: [email protected]