Ural patriot walk-behind tractor. application features, characteristics, owner reviews

Belts for the Neva walk-behind tractor

Basically, Neva walk-behind tractors use V-belt drives. There are a large number of them presented. And for each individual walk-behind tractor, you should know the belt that needs to be used.

Replacing the belt on the Neva walk-behind tractor:

• Remove the shield, unscrew the two bolts (7) and remove the protective casing from the pulleys (6);
• Remove the reverse belt (3) by removing the spring (8), loosening the bolt (2) of the guide pulley;
• Unscrew the screws (5) holding the bracket (a);
• Position the bracket so that the pins allow the front pass belt (10) to be removed from the pulley;
• Put a new belt in its place (first it is put on the gearbox pulley, then on the engine pulley);
• Reassemble everything in reverse order.

Adjust the belt tension! When the clutch levers are released, the belts should sag freely, and the gear pulley should not rotate when the engine is running.

Pulleys are designed to tension transmission belts. There are a large number of them on the Russian market. To replace a pulley, you need to measure its diameter. The following sizes are available: 18, 20 and 25.4 mm.

Rules for working with a walk-behind tractor

In order for the device to work for a long time and without serious problems, you should follow not only the break-in rules, but also the recommendations for operating the equipment.

Experienced farmers recommend following these tips. Before each engine start, check the oil level. If it is not enough, you cannot start the engine. You also need to monitor the fuel level in the tank. For long-term operation of the walk-behind tractor, it is advisable to use only high-quality fuels and lubricants.

After starting the engine, you need to let it run at medium speeds. Only when the engine warms up can you begin full-fledged work. But you shouldn’t load the walk-behind tractor to the maximum. This can significantly affect the service life of some parts. It is necessary to follow the rule regarding the maximum load not only during plowing, but also when transporting goods.

Preparing the walk-behind tractor for running in

You first need to prepare the equipment for the first launch.

Specifics of this process:

• All bolts and fastenings are securely and firmly fixed;
• The brake and steering systems work properly. The steering is in the standard position;
• Bearings and seals are in good condition, worn parts are replaced;
• Check the oil level;
• Following the instructions for use, you need to lubricate all elements (that require it) with oil. The process must be performed very carefully, the oil should not become contaminated.

general characteristics

The Patriot Ural walk-behind tractor is a device that allows you to perform a variety of agricultural work related to cultivating the land.

The model is one of the most popular walk-behind tractors in the Patriot line, characterized by moderate weight and ease of maintenance.

The Patriot Ural walk-behind tractor runs on a four-stroke gasoline engine with a power of 7.8 hp.

The trailer unit is universal, thanks to which all attachments from the manufacturer fit this walk-behind tractor.

You can connect a plow, hiller, potato digger and other popular additional equipment to the unit.

If necessary, you can connect a light-duty trolley or a trailer.

Please note that the Patriot Ural walk-behind tractor is intended for use on small plots of land. For industrial purposes, other, heavier and larger models are used.

For industrial purposes, other, heavier and larger models are used.

It is recommended to operate the device according to the instructions.

Next, we will tell you what is remarkable about this model and how to use this walk-behind tractor correctly.

Running in a gasoline and diesel walk-behind tractor

The running-in procedure for diesel walk-behind tractors is the same as for gasoline ones. The instructions for a specific model indicate the running-in stages, load, operating time in each gear, and the total number of hours. Diesel and gasoline walk-behind tractors are always run at medium speeds, following the general rules:

• Before each start-up, check the oil level and top it up if it is below normal;
• use only recommended brands of fuel;
• When operating attachments, do not exceed the load recommended by the manufacturer.

When all the break-in hours have been completed, a complete oil change is performed in the transmission units and engine.

Purpose and design features

Patriot Ural is a durable device designed for processing soil of any complexity. The equipment is also suitable for transporting goods over short distances. The reinforced frame provides superior off-road capabilities. In addition to the frame, the design of the device may include additional attachments.

• The reinforced frame can serve as a handle for convenient movement of the walk-behind tractor. The frame also protects the motor in the event of a rollover. The main frame has several holes to which a “hitch” is attached, driven by a drive pulley. This equipment has the ability to bend in order to protect it from scratches and other external influences.
• Additional frame - located under the bottom of the engine compartment. By design, this is a simple technical addition, but it plays a very important role in terms of increasing functionality. The frame is so strong that it will support various containers and boxes, and at the same time protect the motor from collisions and shocks. For greater reliability, an additional frame is attached to the main frame and control handle.
• The walk-behind tractor is equipped with a three-speed gearbox and a belt clutch. The gearbox is made in a cast iron housing, which is very resistant to increased loads. Also, the cast iron construction avoids various leaks. The gearbox is convenient to operate due to the fact that its lever is located towards the operator.
• If necessary, you can remove the fenders and mudguards that trap clods of earth.
• The list of equipment includes a powerful headlight with effective lighting regardless of the time of day.
• Cross-country ability is improved by pneumatic wheels. Their impressive dimensions give confidence when overcoming bumps, bumps and other off-road elements.
• The design of the device includes a separate lubrication system. This means that there is no need to mix fuel and oil when filling. In addition, this system increases torque. The basic version of the walk-behind tractor includes tillage cutters, an S-shaped coulter, a bracket, discs and pneumatic wheels.

General information

The Patriot brand originally originated in America, and not in Russia, as it might seem at first glance. Later, walk-behind tractors under this brand began to be produced in China. Cheap labor in this country has significantly reduced the cost of the model. But at the same time, production is under the complete control of American specialists. Moreover, the Chinese Ural assembly plant meets all international standards. Many modifications allow you to choose the best option depending on the customer’s needs.

The Patriot Ural walk-behind tractor is considered more expensive than its Russian counterparts. The model range of the American brand is extensive and diverse, and in terms of reliability, Patriot products are in many ways superior to domestic models, which is an undeniable competitive advantage. The Patriot Ural technology has existed in Russia for quite a long time, and is among the most popular.

Advantages and disadvantages

Like all Patriot brand walk-behind tractors, this model is distinguished by decent reliability, so the need to buy spare parts arises relatively rarely. But if it does appear, the repair is quite simple. The device performs well both on farmland and in garden plots of various sizes. Thanks to mounted structures, excellent performance can be guaranteed both when cultivating land and during other work. You can move the walk-behind tractor alone, but due to its considerable weight it is better to move it together.

The rubberized control handles are very comfortable to hold, especially since the handle is adjustable to individual needs. Filling gasoline into the wide neck is quite easy and prevents spills. A wide range of speeds allows you to work confidently both when cultivating land and when moving loads, which requires driving faster. The special design of the casing minimizes the risk of drive belt breakage. The air filter prolongs engine life.

The weak point of the Patriot Ural can be considered that this model cannot cope with industrial cultivation of the land. It is used only on small private lands. It’s also worth noting that driving in the snow without lugs or converting to a tracked version is impossible. Fuel consumption is relatively high, but this is a common characteristic of all gasoline devices. As for the inability to cultivate heavy soil, given the available power, the device should not be able to cope with such work. Sometimes they note such a nuance as the weakness and insufficient width of the control handles, due to which control is a little complicated, and the wheels can wear out quickly.

Patriot brand - history of appearance

Patriot was founded in 1973 by American engineer Andy Johnson, who, after his dismissal, opened his own business and created a company for repairing equipment for gardening. The company was actively developing, producing its own products, including lubricants for equipment under the PATRIOTS brand. The name was not invented by Johnson by chance, but in honor of his favorite football club.

In 1976, Patriot entered into a service contract with Home Depot.

Since 1986, it has been producing supplies for garden equipment together with Home Depot.

In 1991-1992, the first engines for garden equipment appeared and the production of GARDEN PATRIOTS chainsaws began.

Since 1996, it has been developing new, more powerful engines and expanding its lines of lubricants for spare parts.

In 1997, he broke the contract with Home Depot and formed the independent PATRIOT brand.

Since 1999, Patriot products have appeared in Russia. This is facilitated by the Garden Trading company. She also registers the Patriot Garden trademark in Russia.

In 2011, Garden Trading returned the Patriot brand to its original name.

The range of equipment is expanding; various types of equipment are being produced in Russia, China, Italy, and Korea.

Everything continues with the development of a unified design in 2012 for recognition of the Patriot brand.

Currently, the company has representative offices in Ukraine and Belarus, and there are many service centers throughout the Russian Federation.

The Patriot company produces its own line of lubricants; in addition, it produces various electrical and gasoline equipment, construction, power and garden equipment.

Nevada

There are 2 variants of this model on the market: Nevada 9 and Patriot Nevada Diesel PRO walk-behind tractor.

Technical indicators of both versions:

Advantages of the Patriot Nevada technology:

• a reinforced frame is installed, which helps protect the engine and gearbox from impacts during work;
• You can install a headlight on the handle, which will allow you to operate the device at night;
• the presence of a coulter, which is necessary for deep plowing of the soil;
• wheels of a stable type, which increases the level of maneuverability when passing through loose or wet soils;
• reinforced bumper that protects internal parts from damage.

The Patriot Nevada Comfort unit is equipped with a rubberized handle and a protective cover.

Equipment, maintenance and operation

The factory package includes: the Patriot Ural walk-behind tractor itself, a set of cutters, a towbar, a coulter, a spark plug wrench, two wings and two pneumatic wheels, as well as an instruction manual.

The manufacturer recommends adhering to the maintenance standards specified in the instructions and using only those brands of oils and types of fuel that are indicated for this model of walk-behind tractor.

To fill the gearbox oil in the Patriot Ural walk-behind tractor, you can use HYPOID gear oil.

For the engine, it is recommended to use 4-stroke semi-synthetic EXPERT SAE 10W-40, or SPECIFIC SAE 5W-30, as well as SUPREME HD SAE30 - mineral oil for 4-stroke engines.

Gasoline for refueling the engine: grade AI92. Low-quality fuel impairs the performance of the unit, quickly clogs the fuel filter and accelerates wear of leading parts, including the engine.

According to the operating instructions, changing the oil on the Patriot Ural walk-behind tractor should be done:

• 5 hours after the first start;
• once a season, or after 20-50 working hours.

Fuel can only be added to the tank after the engine has cooled down.

Before work, you need to warm up the engine, then select a speed mode, press the clutch and, holding it, move off.

It is recommended to engage reverse gear on all Patriot line walk-behind tractors only for turning the walk-behind tractor in place.

During scheduled technical inspections the following is performed:

• replacing or cleaning the fuel filter;
• cleaning external elements from dirt;
• checking the spark plug (cleaning or replacing, adjusting the gap) - every 25 hours of operation;
• Check drive belts or replace if worn.

How to break in engines of different brands?

Manufacturers' recommendations for running in engines of current brands:

• Briggs&Stratton (Briggs and Stratton) . There are no instructions as such for running in engines of this brand. The only thing is that you need to change the oil every five to eight hours of operation. EXI series motors do not require an oil change at all throughout the entire period of operation of the walk-behind tractor;

• Honda (Honda). The engine should not be idled for a long time to prevent oil from accumulating in the crankcase and reducing its lubricating properties. It is recommended to operate the unit at optimal speeds, observe permissible loads, adhere to the frequency of use (after 5 - 20 hours of operation, depending on the model);

• Engine Subaru (Subaru) . General recommendations include: monitoring the condition of the air filter system, spark plugs, fuel system, and the level of contamination of the cylinder fins. Accordingly, the Subaru engine does not need special running-in;

• Lifan (Lifan). Special sensors of the device will not allow the engine to start if there is insufficient oil. You need to run in the walk-behind tractor at medium speeds. The duration of the first operation in gentle mode is five to eight hours. Then the oil is changed again.

Chinese-made engines are also often installed on modern walk-behind tractor models. Most of them are four-stroke and air-cooled.

The grinding of Chinese-made parts is carried out as follows:

• Ten minutes of operation without load and at 2500 rpm (medium load);
• Ten minutes of use without load and at 3000 rpm (slightly lower than high);
• Ten minutes without load and at 3600 rpm (maximum speed);
• Half an hour of operation with a light load at full throttle (cultivation at shallow plowing depth);
• Half an hour of use with an average load at full throttle (average cutter depth during cultivation).

At this point, the run-in stage of the walk-behind tractor can be considered complete. To understand the difference, idle speed is 1200 rpm.

General instructions for running in engines are also suitable for other popular brands: Neva, Schnenli, Centaur, etc.

Technical characteristics of the walk-behind tractor

This brand produces a wide variety of model lines. They have significant differences. This applies to both appearance and performance characteristics. It will be more clear to present the parameters of the most popular, sought-after models in the form of tables.

Technical characteristics of "Patriot MPB-9.0/900":

Technical characteristics of "Patriot Nevada 9":

Technical characteristics of "Patriot Ural":

The main advantage of all the above models and others is the low weight of all models without exception. This is achieved by using parts made of light metals (aluminum) and plastic in the design. The maintenance and repair process is as simple as possible. There are usually no difficulties during assembly.

Engine of the Patriot walk-behind tractor

Without exception, all walk-behind tractors are equipped with single-cylinder engines. The operating principle of this type of engine is 4-stroke.

The main features of such units:

• reliability,
• low fuel consumption,
• light weight.

The main feature of Patriot is the use of its own engines in the design of its walk-behind tractors. Their development became possible in 2009 - a merger was carried out with a large manufacturer of power equipment, Ranger. The fuel used is regular AI-92 gasoline or diesel. The main feature is the lubrication system: special oil should not be added to the fuel

It is important to follow this rule. Otherwise, the walk-behind tractor may require expensive repairs.

At the same time, the equipment is not sensitive to the quality of fuel.

Most walk-behind tractors are equipped with a Patriot P175FB gasoline engine. Its main operating characteristics:

• power, hp - 7.8;
• engine starting system - in manual mode;
• Weight, kg. - 15;
• shaft diameter, mm - 19;
• fuel tank capacity, l - 3.6;
• engine capacity, cm3 - 220.

The engine uses a cast iron liner. Due to this, the average service life increases significantly - up to 2,000 hours.

Gearbox

Depending on the class of equipment produced under this brand, it can be equipped with various types of gearboxes:

The gear type gearbox is used on models with a more powerful engine. These are “Nevada 9” and “Nevada Diesel Pro”. The main difference between gear reducers is the type of clutch - disc in an oil bath. The service life of such equipment is quite high. But maintenance and repairs take much longer.

Chain drive is used on Patriot Pobeda and some other models. A belt clutch is installed with such gearboxes. If necessary, replacing it is quite simple. The necessary parts can be easily purchased in a store or online.

Transmission

The belt-type transmission installed in the Patriot Pobeda has its advantages and disadvantages - typical for all transmissions of this type. The main advantage is the ease of repair and replacement if necessary. All work can be easily performed in the field with a minimum set of tools.

A disc-type clutch in an oil bath is more reliable due to its design features and has a much longer service life. But at the same time, repairing it yourself in the field is quite difficult, sometimes impossible. But in fact this is its only drawback.

Reviews about technical characteristics

Before you make a purchase, you should familiarize yourself with the main characteristics of the walk-behind tractor. The power described above is 5.7 kW. The plowing depth is 32 cm. The equipment weighs 77 kg. The fuel tank, according to consumers, holds quite a lot of gasoline - 3.6 liters. The rotation speed of the cutters is 156 rpm.

The walk-behind tractor moves at a speed of 7 km/h. It is powered by a gasoline engine. The device has a belt clutch. The unit does not have an electric start. Horsepower is 7.8. Reading reviews of the Patriot Ural walk-behind tractor, you can understand that this equipment moves forward in one of 4 speeds. To move backwards, you can use one of two speeds. The engine capacity is 220 cm3.

Ural

READ MORE: Convection in the oven - what is it

The Patriot Ural vehicle has a high-quality, reinforced frame with a bend that goes over the body. This bending gives rigidity to the entire structure and also serves as protection for the muffler, fuel tank and air filter from impacts.

Due to the absence of seams on the gearbox, the possibility of oil leakage is eliminated.

This device includes:

• user guide;
• vomer;
• cutters;
• trailer;
• spark plug key;
• right and left wing;
• wheels.

This model is used to perform agricultural work in medium and large areas.

Dakota PRO

Technical parameters of the Patriot Dakota PRO unit:

The advantages of this walk-behind tractor model:

• 3 position steering wheel adjustment;
• the gear shift knob is located next to the steering wheel;
• cutters are made of hardened steel, they smoothly penetrate the soil, loosen it and raise the soil layer;
• Due to the large pneumatic wheels, the unit has increased stability;
• the powerful engine installed here provides a high level of performance;
• a wide range of attachments can be attached to the device using a pulley;
• electronic ignition allows you to speed up the engine starting process;
• low noise level during operation.

Ural with UMZ-5V engine

The engine of the Ural UMZ-5V walk-behind tractor is a 4-stroke, 1-cylinder gasoline unit with a volume of 475 cm³. The motor was originally created for use on self-propelled agricultural machinery and stationary installations. The power unit develops a power of 4.5 liters. With. at 2000 rpm. The plant allows a short-term increase in power up to 5 hp. With. by increasing the speed.

Long-term operation at high power is not allowed, as it leads to overheating.

The engine is equipped with an air cooling system. To cool the engine, a fan is used that forces air into a casing located around the cylinder and head. When operating a walk-behind tractor, it is necessary to regularly inspect and clean the cooling fins from dust and oil. Accumulated dust impairs heat transfer and causes local overheating, which leads to increased engine wear.

The motor is equipped with an automatic speed controller. For this, a centrifugal mechanism is used, which does not allow a rotation speed of more than 2350 rpm. When the speed is exceeded, the throttle valve shifts, which leads to a drop in rotation speed. The engine manufacturer prohibits self-adjustment of the rev limiter, as well as its use to control the speed.

The gas distribution system consists of 2 lower valves. Because of this, the engine has a low compression ratio of 6 units. The engine uses automobile gasoline A-76 (A-80) as fuel. The fuel supply is located in a tank located above the engine carburetor; the liquid is supplied by gravity. The fuel reserve in the tank is 6 liters, which provides an operating time of up to 4-4.5 hours. Operating time depends on the condition of the engine and the nature of the tasks performed.

The engine of the Ural walk-behind tractor is equipped with a 2-speed gearbox with reduction gears. The first speed reduces the rotation speed by 6 times and is used to perform work with a high coefficient of resistance (for example, plowing virgin soil). The second speed reduces the speed by 2.91 times and is used for operating the product with a trailer or when plowing soft soil. Switching the speeds of the UMB-K Ural walk-behind tractor according to the instructions is carried out with the engine not running.

The engine is started with a cord that is wound around the flywheel. Before starting, it is necessary to set the crankshaft to the compression end position. Starting the engine is permitted in 1st or 2nd gear of the motor gearbox.

The engine output shaft is equipped with a 2-ribbed pulley designed to transmit torque to an additional gearbox and to drive attachments. On the fan side there is a second pulley used to drive attachments that require increased rotation speed of the working parts. The clutch mechanism consists of belts and tension rollers.

According to the repair instructions, the transmission crankcase of a walk-behind tractor with a UMZ-5V engine is filled with 1.5 liters of transmission oil. The substance is poured through a hole closed with a plastic stopper.

The standard set of attachments for the walk-behind tractor included a cultivator. To transport cargo weighing up to 350 kg, a 2-wheel TOP-350/350M trolley was used. When using a single-body plow, the installation of an adapter device is required, which is attached to the frame. The plow can be used in conjunction with metal wheels equipped with lugs. A mounted potato digger is used in conjunction with a plow.

Model Patriot Ural video

https://www.youtube.com/watch?v=BPma7Zq5JpM

The Patriot Ural walk-behind tractor is a durable and multifunctional device, widely used for cultivating land. Thanks to the reinforced frame, unloading and loading of this model is extremely simple.

Patriot Ural is made according to the classical design. special equipment consists of 4 main elements: frame, engine (transverse arrangement), power take-off gearbox and gearbox. In addition to the drive wheels, additional supporting equipment can be installed on the walk-behind tractor.

Design features of the Patriot Ural model:

• special reinforced frame. It can be used as a handle to move the device, and again serves as protection for the motor when tipping over. On the main frame there is a hole for mounting a “hitch” driven by a drive pulley. This element bends along the surface of the equipment, protecting it from scratches and damage;
• additional frame that distinguishes it from analogues. She closes the motor from above. Technically, this addition looks simple, but it performs a very important function. Motoblocks are quite heavy equipment. It takes a lot of effort to move them, especially if you have to pull them sideways. Ural Patriot can be lifted by the frame and moved in the required direction. You can again place containers and boxes on the frame. In addition, the element provides additional protection for the motor during collisions and impacts. An additional frame is attached to the control handle and to the main frame;
• gearbox with 4 front and 2 reverse gears. The walk-behind tractor has a collapsible chain gearbox (2 forward speeds, 1 reverse speed). An increased number of gears is achieved by throwing the belt onto free streams. At the same time, the owner of the equipment can use only 3 gears. Clutch type: belt. The gearbox itself is enclosed in a cast iron housing, allowing it to work with increased loads. It eliminates oil leakage and guarantees a long service life. The output shaft has a hexagonal shape;
• The gear shift handle is located towards the operator. It is used to select a gear.
• removable fenders and mudguards. The elements serve to retain lumps of earth;
• powerful headlight that allows you to work in the dark;
• pneumatic wheels providing increased maneuverability. The size of the wheels is quite large, which makes it easier to overcome uneven surfaces, bumps and other obstacles;

Patriot Ural is equipped with a separate lubrication system, which eliminates the need to mix fuel with oil and increases the torque of the device. again, the model has a wide neck of the fuel tank, making it easier to fill the fuel, and rubber lining on the handles, increasing the operator’s comfort.

The delivery set for the walk-behind tractor includes tillage cutters, an S-shaped coulter with a bracket, pneumatic wheels and discs that provide plant protection.

A wide range of attachments is provided for the Patriot Ural walk-behind tractor:

• multifunctional walk-behind tractor trailer Patriot PM-03;
• plowing module Patriot PM-05;
• two-row hiller Patriot OK2 700.500.13;
• multifunctional hitch Patriot;
• disk hiller Patriot OKD 700.625.17;
• plow Patriot PL 255.567.316.6 with hitch;
• Patriot potato digger without hitch;
• wheel axle extension Patriot UMB S24.370;
• snow blade Patriot OS 100;
• Patriot S-24 lugs.

The power of the walk-behind tractor is quite enough to work with any mounted and trailed equipment. Additional devices are again installed at the front (a third runner on the drive pulley is used for drive).

Run-in

Patriot Ural will last much longer with proper maintenance. It should be performed regularly and efficiently. Again, before the first start, it is necessary to run in the walk-behind tractor. This process is mandatory and allows you to extend the life of the equipment. Run-in is carried out in several steps:

refueling the tank (for the first start, you should choose high-quality fuel); checking the oil level. It is recommended to do it not only before running in, but also before starting any work with the walk-behind tractor; first launch. special equipment should work for some time at medium speeds, after which you should try all available gears, alternating them; checking the functionality of the walk-behind tractor: mowing grass, cultivating soil, transporting goods

It is important here not to exceed the loading standards provided for in the instructions. The duration of this stage is usually 8-9 hours; Change of oil.

Running in individual models of walk-behind tractors

Before the first start, study the instructions in detail. Carefully read the paragraph about running-in. For engines of the same brand, the recommendations for the first start are the same.

Neva

To completely grind in the transmission and all parts of the Subaru engine, the Neva walk-behind tractor is run in for 20 hours. To prevent overload, follow the recommendations:

• transport cargo whose weight does not exceed 150 kg;
• Do not treat clay and rocky soil with a milling cutter.

Before each start-up, the oil level is checked with a dipstick (TEP-15), the first replacement is carried out after 25-50 hours of operation.

How long to break in a walk-behind tractor

By referring to the operating instructions for walk-behind tractors of several popular brands, we will take a closer look at the running-in time of the units.

1. Neva MB-1, MB-2 and MB-23:

• the first 20 hours of operation of the MB-1 are a break-in period;
• The MB-2 walk-behind tractor of the Neva brand with a Briggs Stratton 6.5 engine is recommended to be run in for the first 25 hours of operation;
• The running-in period for the MB-23 MultiAgro model with a Japanese engine (YAMAHA or Subaru) is 20 hours.

Oka (with Lifan engine) runs for 30 hours. Agate – it is recommended to run in walk-behind tractors of this brand within the first 25 hours. Ural (ZiD) with a UMZ-5B engine - the 1996 operating instructions say that the engine break-in period should be at least 60 hours. At the same time, the UMZ-5A and UMZ-6A engines require running-in. Zirka (LX 1090D with diesel engine R180 or 190N) has a break-in period of the first 25 hours of operation. MTZ: The Belarus 09H walk-behind tractor is recommended to be run in for 50 hours, during which the machine parts are broken in. Motor Sich MB-6 and MB-9: the instructions for both the first and second walk-behind tractor say that they must be run in for at least 10 hours before use.

Sequence of actions for running in a walk-behind tractor

During break-in, all parts of the engine, transmission and chassis are ground in and worked out. In practice, this is a gentle mode of operation of the walk-behind tractor.

Run-in is carried out following four basic rules:

1. Oil level. It must be checked before each engine start;
2. Refilling the fuel tank. The operation is not difficult, but it is recommended to use the brand specified by the manufacturer in the operating instructions for the unit;
3. Starting the walk-behind tractor. The engine should run at medium speed for some time. All gears need to be tested within an hour. In this way, the engine is not only run in, but the device is also set up for further operation;
4. Functionality of the unit. This stage includes work on cultivation, plowing and transporting goods. It is important to adhere to the maximum permissible load.

Every owner of a walk-behind tractor needs to know about the features of running in the device. When the process is completed, the oil in the engine and all transmission components is replaced. Running in the engine of a walk-behind tractor at idle cannot be done without moving, since such actions can provoke extremely negative consequences for the unit.

Before starting work, you must carefully study the instructions. Manufacturers provide general recommendations for running in a particular brand of engine. At the same time, there is no particular difference in the running-in of a diesel walk-behind tractor and a gasoline one.

Description

The Patriot Ural walk-behind tractor is adapted for use on dense soils, including virgin soil. It becomes quite multifunctional when using various attachments. The main purpose is to carry out cultivation, so an active cutter is supplied in the kit. But, with the help of the unit, you can plow the ground, mow the grass, plant and harvest potatoes, and also perform other functions.

Motoblock Patriot Ural

• The engine of the Patriot "Ural" walk-behind tractor is gasoline and has a power of 7.8 hp, which allows the device to be classified as a middle class one.
• The total weight is 87 kg.
• The model is made in a compact size, which makes it possible to save space during storage.

Management is simple and does not require additional knowledge. The ergonomic handle, on which all the necessary controls are located, can be adjusted in height. Gears are changed using a lever. The gearbox has 4 forward and 2 reverse speeds, allowing you to maneuver during work. This amount is achieved through the use of reduced speeds.

The gear shift knob is long, allowing the operator to easily reach it. The gearbox is made in a cast iron housing, which protects working parts from damage.

Reviews about the main features of "Patriot Ural 440108000"

This version of the equipment, according to consumers, has a reinforced frame and is easy to transport. The protection device operates on a four-stroke engine with a volume of 220 cubic centimeters. Clean air is supplied to the device engine by an oil-filled air filter. According to users, this eliminates damage when working in dusty conditions. Among other things, the service life of the unit is increased.

The cutters have durable 4 cm blades. Curved knives smoothly enter the ground. After reading the reviews about the Patriot Ural walk-behind tractor, you will be able to understand that attachments can be used together with the equipment. The unit is multifunctional. It has pneumatic wheels that provide excellent maneuverability. The cultivation depth varies from 160 to 320 mm.