For questions regarding the purchase of this equipment (KS-55713-1K Klintsy truck crane on KAMAZ-65115 chassis), terms of credit and leasing, service and warranty, please contact the plant’s dealers or official representative offices. Delivery of the KS-55713-1K Klintsy truck crane on the KAMAZ-65115 chassis can be carried out either directly from the manufacturer or from sites in Moscow and other regions of the Russian Federation.
Invariably enjoys particular popularity among consumers of Klintsy truck cranes. A large support contour (4.9x5.8), additional single-file configuration with variable tilt geometry, a reliable chassis, a circular work area, five operating modes, the ability to work in cramped conditions - all this makes this model functional, highly productive and, as a result, the most popular in the world. market. It is unique in its load-height characteristics and is the only model among the 25-ton truck cranes produced by manufacturers with a circular work area.
Description
KS-55713-1K - the most popular
The KS-55713-1K automobile jib crane with a lifting capacity of 25 tons is mounted on the chassis of a KamAZ-65115 vehicle.
It is unique in its load-height characteristics and is the only model among the 25-ton truck cranes produced by manufacturers with a circular work area.
Invariably enjoys particular popularity among consumers of Klintsy truck cranes. A large support contour (4.9x5.8), additional single-file configuration with variable tilt geometry, a reliable chassis, a circular work area, five operating modes, the ability to work in cramped conditions - all this makes this model functional, highly productive and, as a result, the most popular in the world. market.
Actuator drive
The crane installation is driven by an axial piston hydraulic pump, which is driven by the engine of the base vehicle through a gearbox and an additional power take-off.
The crane mechanisms have an individual drive with independent control from hydraulic motors and hydraulic cylinders.
The hydraulic system, based on imported components, allows for easy and smooth control of crane mechanisms with a wide range of speed control for working operations and the ability to simultaneously combine any crane operations.
Boom and telescoping system
A three-section telescopic boom with a length of 9-21 meters in the retracted position provides the crane with compactness and maneuverability when moving, and in the extended position it provides a wide working area and a greater height of movement of the load during operation.
The ability to telescope a boom with a load on a hook allows the crane to perform special tasks: installing loads in hard-to-reach places, carrying them among mounted structures.
Additional equipment expands the range of possibilities
Additional equipment of the boom with a lattice jib 7.5 meters long with the possibility of installation at an angle of 0 and 30 degrees relative to the boom allows for the largest service area and the size of the under-boom space. The transfer of the jib from the transport position to the working position and back is done manually without the use of additional lifting equipment.
Functionality and performance
Due to the large size of the support contour (4.9 x 5.8!!!), the crane can carry out work with loads in a 360-degree circular zone, which allows minimizing the number of rearrangements when working on site. Thus, the functionality and performance of this crane model on work sites significantly exceeds that of existing analogues.
For the convenience of working in cramped conditions, an operating mode is provided with the crane installed on supports with the outrigger beams retracted.
Load-bearing structures of optimal weight
The main supporting structures are welded from high-strength steel 10HSND, are as lightweight as possible, and have excellent rigidity characteristics.
All welded joints are made using semi-automatic and automatic welding equipment from domestic and European manufacturers, which ensures the highest quality of seams, which is documented after ultrasonic testing.
Truck crane reliability
Reliable operation of the truck crane is ensured by foreign-made components that do not require replacement or repair during the entire service life of the crane.
Truck crane safety
Safe operation of the crane is ensured by a complex of instruments and devices, including the load limiter of the crane ONK with a digital indication of operating parameters on the display in the crane operator’s cabin, which includes a built-in device for recording characteristics - a “black box” and a module for protecting the crane from dangerous voltage MZON for operation near power lines. The PMC automatically protects the crane from overload and capsizing, and is equipped with a coordinate protection system necessary for working in cramped working conditions near power lines.
Convenient crane operator workplace
The truck crane is equipped with a crane operator's cabin that meets the latest requirements for comfort and visibility: a compartment-type sliding door, a diesel heater, a fan, a folding rear hatch, and a convenient instrument panel.
Convenience of control of crane operations is achieved due to the original arrangement of control levers.
Guarantees
The crane's warranty period is 18 months or 1000 operating hours in crane mode from the moment the crane is handed over to the consumer. The service life of the crane with 1.5-shift operation in certified mode is 10 years. Each crane is equipped with an individual set of spare parts for the base chassis and the crane installation.
Load height characteristics of the crane
The Klintsy KS-55713-1K automobile jib crane with a lifting capacity of 25 tons is mounted on the KamAZ-55111 and KamAZ-53215 chassis. The truck crane is designed to perform loading and unloading, construction and installation work at dispersed sites. Excellent maneuverability and ease of chassis control, compact dimensions - all this makes the truck crane indispensable when used in cramped conditions of modern cities.
The crane installation is driven by an axial piston hydraulic pump, which is driven by the engine of the base vehicle through a gearbox and an additional gearbox. The crane mechanisms have an individual drive with independent control from hydraulic motors and hydraulic cylinders.
Hydraulic
The crane installation system provides smooth control of all mechanisms with a wide range of speed control for working operations, as well as the ability to simultaneously combine several crane operations.
The truck crane is equipped with retractable hydraulic supports. For the convenience of working in cramped conditions, the truck crane has a mode for working with loads with installation on supports with the outrigger beams retracted.
Maximum size of the support contour of the truck crane ( 5.25 x 5.8
m!!!) is achieved through the use of outrigger structures with folding support beams. Due to this, the crane is able to carry out work with loads in a 360° circular zone and, as a result, the number of rearrangements of the truck crane when working on site is minimized. Thus, the functionality and performance of this crane model on work sites significantly exceeds that of existing analogues.
Three-section telescopic
a boom with a length of 9 - 21 m provides the truck crane with compactness and maneuverability when moving, a wide area and a large height for moving cargo during operation.
The boom telescoping system includes one
extension hydraulic cylinder and a rope pulley. The ability to telescope the boom with a load on the hook allows the truck crane to perform special tasks: installing loads in hard-to-reach places, carrying them among mounted structures.
Additional equipment of the boom with a lattice jib 7.5 m long with the possibility of installation at an angle of 0° and 30° relative to the boom allows for the largest service area and the size of the under-boom space.
Safe operation of the crane is ensured by a set of special instruments and devices, including a microprocessor-based load limiter with coordinate protection, which automatically protects the cranes from overload and tipping, limits the movement of the moving part of the cranes in a given working area (working in cramped conditions or near power lines), and issues information about the operation of the crane on the display in the driver's cabin.
The load limiter has a built-in device for recording characteristics - a “black box” and a built-in module for protecting the crane from dangerous voltage (MZON) for operating the truck crane near power lines.
| Crane specifications echo $name; ?> | |
| Maximum load capacity, t | 25 |
| Maximum load moment, tm | 80 |
| Telescopic boom length, m | 9,0…21,0 |
| Jib length, m | 7,5 |
| Jib installation angle | 0°; 30° |
| Maximum hook lifting height, m | |
| with main boom | 21,6 |
| The maximum depth of lowering the hook with the boom is 9 m at a reach of 5.7 m, reeving 6-fold, m | 13 |
| Maximum mass of telescopic load, t | 6,0 |
| Hook lifting (lowering) speed, m/min | |
| nominal (with a load weighing up to 25 tons) | 5,2 |
| maximum (with load up to 4.5 t) | 11 |
| maximum (pulley multiplicity 1) | 40 |
| Landing speed, m/min | 0,2 |
| Turntable rotation speed, rpm | 1,2 |
| Crane working area | 360° |
| Basic chassis | KamAZ-53215 KamAZ-55111 |
| Crane travel speed, km/h | up to 80 |
| Crane weight in transport position, t | 20,2 |
| Support contour size, mm | |
| along the chassis axis | 4 900 |
| across the chassis axis with the outrigger beams extended (retracted) | 5 800 (2 270) |
| Overall dimensions in transport position, mm | |
| length | 11 100 |
| width | 2 500 |
| height | 3 640 |
| Operating temperature, °C | ±40 |
Specifications
| main characteristics of the crane | |
| Maximum load moment, t.m | 80,0 |
| Maximum load capacity, t | 25 |
| Boom length, m | 9-21 |
| Jib length, m | 7,5 |
| Jib installation angle, degrees. | 0 and 30 |
| Crane operating area, deg. | 250 and 360 |
| Maximum hook lifting height, m | |
| — with main boom 21 m | 21,6 |
| — with a main boom of 21 m and a jib of 7.5 m | 29,3 |
| Maximum depth of lowering the hook from the ground level with a boom of 9.0 m, reach of 5.0 m and 6-fold reeving of the rope, m | 13,0 |
| Minimum reach, m | 2,0 |
| Reach, maximum, m (For crane operating area 90°) | |
| a) “design” (no load) | 19,6 |
| b) “worker” (with a load on a hook) | 19,5 |
| Reach at maximum load capacity, m | 3,2 |
| Maximum load weight when telescoping, t | 6,0 |
| Maximum weight of cargo with which the jib crane is allowed to move, t | moving the crane with a load is PROHIBITED! |
| Maximum weight of cargo that can be handled in the accelerated mode of lifting and lowering with a winch, t | 4,5 |
| Operating modes | |
| 5 operating modes: | |
| in the working area 250° with the main boom (9-21m) on extended beams of retractable supports; | |
| in the working area 250° with the main boom (9-15m) on retracted beams of retractable supports; | |
| in the 360° working area with the main boom (9-21m) on extended beams of retractable supports; | |
| in the working area 250° with the main boom (21m) and a jib 7.5m on extended beams of retractable supports with a jib angle of 0°. | |
| in the working area 250° with the main boom (21 m) and a jib 7.5 m on extended beams of retractable supports with a jib angle of 30°. | |
| Crane geometric parameters | |
| Base, m | 3,69+1,32 |
| Track, m: | |
| - front wheels | 2,05 |
| — rear wheels (between the middles of the double slopes) | 1,89 |
| type of supports | retractable |
| Outrigger base, m | 4,9 |
| Size of the support contour along x across the chassis axis, m | |
| with extended support beams | 4.9 x 5.8 |
| with retracted support beams | 4.9 x 2.27 |
| Rear clearance, m | 3,015 |
| Turning radius (according to the main boom size), m | 10 |
| Overall dimensions of the crane in transport position, m | |
| length x width x height | 11.06x2.5x3.64 |
| Working movement speeds | |
| Load lifting and lowering speed, m/min | |
| — nominal with 6-fold rope reeving (with a load of 18.0 t) | 6,5 |
| — increased with 6-fold rope reeving (with a load of 4.5 tons) | 13,0 |
| — maximum with rope pulley multiplicity 1 (with a load of 2.0 t) | 40,0 |
| Load landing speed, m/min | 0,2 |
| Travel speed of the crane under its own power, km/h | 50,0 |
| Speed of the telescoping mechanism of boom sections (extension - retraction of boom sections), m/s (m/min) | 0,25 (15,0) |
| Turntable rotation speed, rpm | 0,96 |
| Time of full change of reach, s (min), at engine speed up to 1200 rpm: | |
| from maximum to minimum | 45 (0,75) |
| from minimum to maximum | 45 (0,75) |
| additional characteristics | |
| Elevation overcome by the crane, % (degrees): | |
| under its own power | 25 (14) |
| in tow | 18 (10) |
| Control method: | |
| swing frame mechanisms | hydraulic |
| outriggers | hydraulic |
| movement mechanism (chassis) | mechanical |
| Weight of the crane in transport position, t (including 3 people in the driver’s cabin, spare parts kit) Permissible deviation ± 1.5% | |
| main boom crane | 21,10 |
| crane with main boom and jib | 21,55 |
| Weight of the main assembly parts of the crane, t: | |
| crane installation | 12,85 |
| counterweight | 0,4 |
| arrow | 3,65 |
| goose | 0,45 |
| Load distribution along axes in transport position, kN (tf) Permissible deviation ± 1.5%: | |
| front axle | |
| main boom crane | 51,45 (5,25) |
| crane with main boom and jib | 54,39 (5,55) |
| rear trolley | |
| main boom crane | 155,33 (15,85) |
| crane with main boom and jib | 156,8 (16,00) |
| Maximum load on outrigger, t | 25,8 |
| Control fuel consumption in crane mode, l/h, no more | 13 |
| Refill containers: | |
| Hydraulic system (including hydraulic tank), l | 385 (240) |
| Heater fuel tank, l | 5 |
| Turning mechanism housing, l | 5 |
| Cargo winch gearbox, l | 11 |
| Operating temperature, degrees. | from -40° to +40° |
| general characteristics of the chassis | |
| Chassis type | KamAZ - 65115-62 |
| Axial formula | 1-2 |
| Wheel drive and control formula | 6 x 4 |
| Transmission type | hydromechanical |
| Steering system | via power steering |
| Braking system: | |
| the main one is pneumatic, with separate drive of the front and rear wheel brakes | |
| auxiliary - engine brake-retarder with two flaps in the exhaust system | |
| parking - pneumatic | |
| Axle suspension system | spring |
| Tire size: | |
| For KAMAZ-65115-0001963-62 chassis | 10.00 R20 |
| For KAMAZ-65115-0001942-62 chassis | 11.00 R20 |
| engine's type | KamAZ-740.62-280, Euro3 |
| Diesel, four-stroke diesel with turbocharging, eight-cylinder | |
| Installed power, kW (hp) | 206 (280) |
| Specific fuel consumption, g/kWh | 117 |
| Fuel tank capacity, l | 210 |
| Cruising range, km | 700 |
| Permissible loads on bridges when moving, kN (t) | |
| For KAMAZ-65115-0001963-62 chassis | |
| To the front axles | 54,39 (5,55) |
| To the rear axles | 165,13 (16,85) |
| For KAMAZ-65115-0001942-62 chassis | |
| To the front axles | 60,76 (6,20) |
| To the rear axles | 186,20 (19,00) |
| Chassis weight distribution, t: | |
| to the front axles | 36,85 (3,76) |
| to the rear axles | 36,06 (3,68) |
The truck crane is designed to perform loading and unloading, construction and installation work at dispersed sites. All chassis have excellent maneuverability and ease of control, which allows this truck crane to be used at sites with various types of access roads, and its small dimensions make it suitable for use in cramped conditions of modern cities.
To facilitate engine starting in the cold season, the chassis is equipped with an autonomous pre-heating system, which simultaneously functions as an autonomous heater for the driver's cabin. In this case, the cabin can be heated when the engine is not running.
Crane drive - hydraulic
, is carried out using two axial piston hydraulic pumps, which are driven by the engine of the base vehicle through a gearbox and an additional power take-off. The crane mechanisms have an individual drive with independent control from hydraulic motors and hydraulic cylinders. The hydraulic system of the crane installation ensures smooth control of all mechanisms with a wide range of speed control for working operations, as well as the ability to simultaneously combine several crane operations.
Three-section telescopic
a boom with a length of 9.7 - 21.7 m in the retracted position provides the crane with compactness and maneuverability when moving, and in the extended position it provides a large working area and a large height for moving the load during operation.
Additional equipment of the boom with a lattice jib 9 m long ( except for a truck crane based on the KamAZ-53215 chassis
) allows you to provide the largest service area and the size of the boom space among similar models of 25-ton truck cranes. The transfer of the jib from the transport position to the working position and back is done manually without the use of additional lifting equipment.
The ability to telescope a boom with a load on a hook allows the KS-55713-1 truck crane to perform special tasks: install loads in hard-to-reach places, carry them among mounted structures. For the convenience of working in cramped conditions, a load handling mode is provided with the installation of the truck crane on supports with the outrigger beams retracted.
Safe operation of the crane is ensured by a complex of instruments and devices, including a microprocessor load limiter with digital indication of operating parameters on the display in the driver’s cabin. The device automatically protects the crane from overload and capsizing, is equipped with a crane coordinate protection system necessary for working in cramped conditions, has a built-in telemetric memory unit (“black box”) and a crane protection module from dangerous voltage (MZON) for operating the truck crane near power lines .
Load height characteristics
Click on the image to view a larger version:
Cargo characteristics
A) Load characteristics of the crane operating on retractable supports with 6 and 8 fold reeving of the rope, the beams of the retractable supports are fully extended, the crane is installed on the supports, the work area is 250°.
| Reach, m | Boom length, m | 9.0-15.0 (boom telescoping with a load on the hook) | 15.0-21.0 (boom telescoping with a load on the hook) | Crane operating area, degrees * | ||||||
| 9,0 | 9,0 | 12,0 | 15,0 | 18,0 | 21,0 | |||||
| Intermediate lifting capacity (on ropes), t | ||||||||||
| 2,0 | 25,0 | 18,0 | 6,0 | 3,0 | ±125 | |||||
| 2,5 | 15,0 | 6,0 | 3,0 | |||||||
| 3,0 | 13,8 | 6,0 | 3,0 | |||||||
| 3,2 | 25,0 | 6,0 | 3,0 | |||||||
| 3,5 | 21,5 | 10,0 | 6,0 | 3,0 | ||||||
| 4,0 | 18,0 | 18,0 | 13,8 | 6,0 | 3,0 | |||||
| 4,2 | 15,0 | 6,0 | 3,0 | |||||||
| 4,5 | 14,2 | 12,8 | 10,0 | 6,4 | 6,0 | 3,0 | ||||
| 5,0 | 13,1 | 13,1 | 12,3 | 11,6 | 9,75 | 6,0 | 3,0 | |||
| 5,5 | 6,4 | 6,0 | 3,0 | |||||||
| 6,0 | 9,6 | 9,6 | 9,25 | 8,8 | 8,0 | 6,1 | 6,0 | 3,0 | ||
| 7,0 | 7,4 | 7,4 | 7,2 | 6,9 | 6,5 | 5,5 | 6,0 | 3,0 | ||
| 7,5 | 6,6 | 6,6 | 3,0 | |||||||
| 8,0 | 5,8 | 5,6 | 5,35 | 4,8 | 5,6 | 3,0 | ||||
| 9,0 | 4,85 | 4,45 | 4,1 | 3,0 | ||||||
| 10,0 | 4,05 | 3,9 | 3,7 | 3,5 | 3,9 | 3,0 | ||||
| 10,5 | 3,75 | |||||||||
| 12,0 | 2,85 | 2,7 | 2,55 | 2,85 | 2,55 | |||||
| 13,0 | 2,45 | 2,45 | ||||||||
| 13,5 | 2,25 | 2,25 | ||||||||
| 14,0 | 2,0 | 1,9 | 1,9 | |||||||
| 15,0 | ||||||||||
| 16,0 | 1,55 | 1,45 | 1,45 | |||||||
| 16,5 | 1,45 | |||||||||
| 18,0 | 1,1 | 1,1 | ||||||||
| 19,5 | 0,9 | 0,9 | ||||||||
| Multiplicity of chain hoist, m | 8 | 6 | 8;6 | 8; 6 | 8; 6 | 8; 6 | 8; 6 | 8; 6 | ||
* From the crane position “boom back”.
Note:
- When the boom length increases over 9.0 m, the maximum lifting capacity of the crane decreases from 25.0 t to 15.0 t and lower depending on the boom length, which is controlled by the ONK-140 crane load limiter and limit switch.
- When you switch the reeving multiplicity button on the front panel of the load limiter to m=6, the load capacity is reduced to 18.0t.
- The mass of the hook suspension (0.28 t) and removable load-handling devices are included in the mass of the lifted load.
- When the crane operates with a jib fixed to the base of the boom in the transport position, the crane's lifting capacity is reduced by 0.23 tons, which is controlled by the load limiter.
- Operating modes of the load limiter of the ONK-140-R-00 crane.
B) Load characteristics of the crane operating on retractable supports with 6 and 8 fold reeving of the rope, the beams of the retractable supports are fully extended, the crane is installed on supports, the work area is 360°.
| Reach, m | Boom length, m | 9.0-15.0 (boom telescoping with a load on the hook) | 15.0-21.0 (boom telescoping with a load on the hook) | Crane operating area, degrees * | ||||
| 9,0 | 12,0 | 15,0 | 18,0 | 21,0 | ||||
| Intermediate lifting capacity (on ropes), t | ||||||||
| 2,0 | 15,0 | 6,0 | 3,0 | ±180 | ||||
| 2,5 | 12,0 | 6,0 | 3,0 | |||||
| 2,8 | 10,0 | 6,0 | 3,0 | |||||
| 3,2 | 15,0 | 6,0 | 3,0 | |||||
| 3,5 | 13,6 | 8,0 | 6,0 | 3,0 | ||||
| 3,6 | 12,0 | 6,0 | 3,0 | |||||
| 3,8 | 10,0 | 6,0 | 3,0 | |||||
| 4,0 | 11,4 | 10,4 | 8,0 | 6,0 | 3,0 | |||
| 4,5 | 8,45 | 7,5 | 4,4 | 6,0 | 3,0 | |||
| 5,0 | 7,5 | 6,7 | 6,05 | 5,25 | 4,4 | 6,0 | 3,0 | |
| 6,0 | 5,0 | 4,6 | 4,1 | 3,7 | 3,2 | 4,1 | 3,0 | |
| 7,0 | 3,55 | 3,3 | 3,0 | 2,75 | 2,4 | 3,0 | 2,4 | |
| 7,5 | 3,0 | |||||||
| 8,0 | 2,5 | 2,25 | 2,05 | 1,85 | 2,25 | 1,85 | ||
| 9,0 | 1,9 | 1,75 | 1,6 | 1,45 | 1,75 | 1,45 | ||
| 10,0 | 1,45 | 1,35 | 1,25 | 1,15 | 1,35 | 1,15 | ||
| 10,5 | 1,25 | |||||||
| 12,0 | 0,75 | 0,7 | 0,65 | 0,75 | 0,65 | |||
| Multiplicity of chain hoist, m | 8; 6 | 8; 6 | 8; 6 | 8; 6 | 8; 6 | 8; 6 | 8; 6 | |
* From the crane position “boom back”.
Note:
- The mass of the hook suspension (0.28 t) and removable load-handling devices are included in the mass of the lifted load.
- When the crane operates with a jib attached to the base of the boom in the transport position, the crane's lifting capacity is reduced by 0.23 tons, which is controlled by the load limiter.
- Operating modes of the load limiter of the ONK-140-R-01 crane.
B) Load characteristics with 8 and 6 fold reeving of the rope, the beams of the retractable supports are retracted, the crane is installed on the supports, the work area is 250°.
| Reach, m | Boom length, m | 9.0-15.0 (boom telescoping with a load on the hook) | Crane operating area, degrees * | |||
| 9,0 | 12,0 | 15,0 | ± 125 | |||
| Intermediate lifting capacity (on ropes), t | ||||||
| 2,0 | 6,0 | 1,0 | ||||
| 2,5 | 5,2 | 1,0 | ||||
| 3,0 | 6,0 | 5,2 | 3,5 | 1,0 | ||
| 3,5 | 3,5 | 1,0 | ||||
| 3,6 | 4,6 | 4,05 | 1,0 | |||
| 4,0 | 3,85 | 3,45 | 3,0 | 1,0 | ||
| 5,0 | 2,6 | 2,35 | 2,1 | 1,0 | ||
| 6,0 | 1,75 | 1,6 | 1,45 | 1,0 | ||
| 7,0 | 1,2 | 1,1 | 1,0 | 1,0 | ||
| 7,5 | 1,0 | 1,0 | ||||
| Multiplicity of chain hoist, m | 8; 6 | 8; 6 | 8; 6 | 8; 6 | ||
* From the crane position “boom back”.
Note:
- The mass of the hook suspension (0.28 t) and removable load-handling devices are included in the mass of the lifted load.
- When the crane operates with a jib attached to the base of the boom in the transport position, the crane's lifting capacity is reduced by 0.23 tons, which is controlled by the load limiter.
- Operating modes of the load limiter of the ONK-140-R-02 crane.
D) Load characteristics of the crane with a single reeving of the rope, boom length 21.0 m with a jib 7.5 m, beams of retractable supports are fully extended, the crane is installed on supports, work area 250°.
| Reach, m | Intermediate lifting capacity (on ropes), t | Crane operating area, degrees * | |
| Tilt angle 0° | Tilt angle 30° | ||
| 7,0 | 2,00 | ± 125 | |
| 8,0 | 2,00 | ||
| 9,0 | 1,75 | 1,30 | |
| 10,0 | 1,55 | 1,20 | |
| 12,0 | 1,25 | 1,05 | |
| 14,0 | 1,05 | 0,90 | |
| 16,0 | 0,85 | 0,75 | |
| 18,0 | 0,70 | 0,65 | |
* From the crane position “boom back”.
Note:
- The mass of the hook suspension (0.04 t) and removable load-handling devices are included in the mass of the lifted load.
- Operating modes of the load limiter of the ONK-140 crane for a tilt angle of 0° - R-03;
- Operating modes of the load limiter of the ONK-140 crane for a tilt angle of 30° - R-04.
Altitude characteristics
A) High-altitude characteristics of the crane operation with 6 and 8 fold reeving of the rope, the beams of the retractable supports are fully extended, the crane is installed on the supports, the work area is 250°.
| Reach, m | Boom length, m | Crane operating area, degrees* | ||||
| 9,0 | 12,0 | 15,0 | 18,0 | 21,0 | ||
| Lifting height, m | ||||||
| 2,0 | 9,8 | ± 125 | ||||
| 2,5 | 12,8 | |||||
| 3,0 | 15,8 | |||||
| 3,2 | 9,2 | |||||
| 3,5 | 9,1 | 18,8 | ||||
| 3,8 | 12,3 | |||||
| 4,0 | 8,7 | 12,2 | 15,5 | |||
| 4,5 | 11,9 | 15,3 | 21,6 | |||
| 5,0 | 7,9 | 11,8 | 15,0 | 18,3 | ||
| 6,0 | 6,7 | 10,9 | 14,5 | 17,9 | 21,1 | |
| 7,0 | 5,0 | 10,1 | 13,9 | 17,4 | 20,7 | |
| 7,5 | 3,0 | |||||
| 8,0 | 9,1 | 13,2 | 16,8 | 20,3 | ||
| 9,0 | 7,6 | 12,4 | 16,2 | 19,7 | ||
| 10,0 | 5,6 | 11,3 | 15,5 | 19,1 | ||
| 10,5 | 3,2 | |||||
| 12,0 | 8,4 | 13,6 | 17,7 | |||
| 13,0 | 5,8 | 12,4 | ||||
| 13,5 | 3,3 | |||||
| 14,0 | 11,0 | 15,8 | ||||
| 15,0 | 9,2 | |||||
| 16,0 | 6,6 | 13,4 | ||||
| 16,5 | 3,5 | |||||
| 18,0 | 9,8 | |||||
| 19,5 | 3,7 | |||||
* From the crane position “boom back”.
B) High-altitude characteristics of the crane operation with 6 and 8 fold reeving of the rope, the beams of the retractable supports are fully extended, the crane is installed on supports, the work area is 360°.
| Reach, m | Boom length, m | Crane operating area, degrees* | ||||
| 9,0 | 12,0 | 15,0 | 18,0 | 21,0 | ||
| Lifting height, m | ||||||
| 2,0 | 9,8 | ± 180 | ||||
| 2,5 | 12,8 | |||||
| 2,8 | 15,9 | |||||
| 3,0 | 15,8 | |||||
| 3,2 | 9,2 | |||||
| 3,5 | 9,1 | 18,8 | ||||
| 3,6 | 12,4 | |||||
| 3,8 | 12,3 | |||||
| 4,0 | 8,7 | 12,2 | 15,5 | |||
| 4,5 | 11,9 | 15,3 | 21,6 | |||
| 5,0 | 7,9 | 11,8 | 15,0 | 18,3 | ||
| 6,0 | 6,7 | 10,9 | 14,5 | 17,9 | 21,1 | |
| 7,0 | 5,0 | 10,1 | 13,9 | 17,4 | 20,7 | |
| 7,5 | 3,0 | |||||
| 8,0 | 9,1 | 13,2 | 16,8 | 20,3 | ||
| 9,0 | 7,6 | 12,4 | 16,2 | 19,7 | ||
| 10,0 | 5,6 | 11,3 | 15,5 | 19,1 | ||
| 10,5 | 3,2 | |||||
| 12,0 | 8,4 | 13,6 | 17,7 | |||
* From the crane position “boom back”.
B) Height characteristics with 8 and 6 fold reeving of the rope, the beams of the retractable supports are retracted, the crane is installed on the supports, the work area is 250°.
| Reach, m | Boom length, m | Crane operating area, degrees* | ||
| 9,0 | 12,0 | 15,0 | ||
| Lifting height, m | ||||
| 2,0 | 9,8 | ± 125 | ||
| 2,5 | 12,8 | |||
| 3,0 | 15,8 | |||
| 3,5 | 9,1 | |||
| 3,6 | 9,0 | 12,4 | ||
| 3,8 | 12,3 | |||
| 4,0 | 8,7 | 12,2 | 15,5 | |
| 5,0 | 7,9 | 11,8 | 15,0 | |
| 6,0 | 6,7 | 10,9 | 14,5 | |
| 7,0 | 5,0 | 10,1 | 13,9 | |
| 7,5 | 3,0 | |||
* From the crane position “boom back”.
D) High-altitude characteristics of the crane operation with a single reeving of the rope, boom length 21.0 m with a jib 7.5 m, beams of retractable supports are fully extended, the crane is installed on supports, work area 250°.
| Reach, m | Lifting height, m | Crane operating area, degrees* | |
| Tilt angle 0° | Tilt angle 30° | ||
| 7,0 | 29,3 | ± 125 | |
| 8,0 | 29,0 | ||
| 9,0 | 28,6 | 28,1 | |
| 10,0 | 28,2 | 27,7 | |
| 12,0 | 27,3 | 26,7 | |
| 14,0 | 26,2 | 25,6 | |
| 16,0 | 24,7 | 24,2 | |
| 18,0 | 23,2 | 22,5 | |
* From the crane position “boom back”.
Truck crane KS-55713-1
Additional Description
The KS-55713-1 automobile jib crane with a lifting capacity of 25 tons is mounted on the chassis of KamAZ-53215, KamAZ-55111 and KamAZ-53229 vehicles. Designed for loading and unloading, construction and installation work at dispersed sites. All chassis have excellent maneuverability and ease of control, which allows the crane to be used at sites with various types of access roads, and its small dimensions make it suitable for operation in the cramped conditions of modern cities.
The crane installation is driven by two axial piston hydraulic pumps, which are driven by the engine of the base vehicle through a gearbox and an additional power take-off. The crane mechanisms have an individual drive with independent control from hydraulic motors and hydraulic cylinders. The hydraulic system of the crane installation ensures smooth control of all mechanisms with a wide range of speed control for working operations, as well as the ability to simultaneously combine several crane operations.
A three-section telescopic boom with a length of 9.7 - 21.7 m in the retracted position provides the crane with compactness and maneuverability when moving, and in the extended position it provides a large working area and a large height for moving the load during operation.
Additional equipment of the boom with a lattice jib 9 m long (except for the crane based on the KamAZ-53215 chassis) allows for the largest service area and the size of the under-jib space among similar models of 25-ton cranes. The transfer of the jib from the transport position to the working position and back is done manually without the use of additional lifting equipment.
The ability to telescope a boom with a load on a hook allows the crane to perform special tasks: installing loads in hard-to-reach places, carrying them among mounted structures. For the convenience of working in cramped conditions, a load handling mode is provided with the crane installed on supports with the outrigger beams retracted.
Safe operation of the crane is ensured by a complex of instruments and devices, including a microprocessor load limiter with digital indication of operating parameters on the display in the driver’s cabin. The device automatically protects the crane from overload and capsizing, is equipped with a crane coordinate protection system necessary for working in cramped conditions, has a built-in telemetric memory unit (“black box”) and a crane protection module from dangerous voltage (MZON) for working near power lines.
Work area
Click on the image to view a larger version:
The crane's operating range is 250° and 360°.
5 operating modes:
- in the working area 250° with the main boom (9-21 meters) on extended beams of retractable supports;
- in the working area 250° with the main boom (9-15 meters) on retracted beams of retractable supports;
- in the 360° working area with the main boom (9-21 meters) on extended beams of retractable supports;
- in the working area 250° with the main boom (21 meters) and a jib 7.5 meters on extended beams of retractable supports with a jib angle of 0°.
- in the working area 250° with the main boom (21 meters) and a jib 7.5 meters on extended beams of retractable supports with a jib angle of 30°.
KS-55713-1 on KamAZ 53215-15 chassis, truck crane, manufactured in 2007.
The procedure for registration of participation in the auction, list of participant documents and requirements for registration: Applications for participation in the auction are submitted in electronic form through the electronic document management system on the Internet site at: https://bankrupt.alfalot.ru/
Procedure and criteria for determining the winner of the auction: The right to acquire the debtor's property belongs to the participant in the auction for the sale of the debtor's property through a public offering, who submitted, within the prescribed period, an application for participation in the auction containing a proposal for the price of the debtor's property, which is not lower than the initial sale price of the debtor's property established for a certain bidding period, in the absence of proposals from other bidders to sell the debtor’s property through a public offer. If several participants in the auction for the sale of the debtor's property through a public offer submitted, within the prescribed period, applications containing different proposals for the price of the debtor's property, but not lower than the initial sale price of the debtor's property established for a certain period of the auction, the right to acquire the debtor's property belongs to the participant auction, which offered the maximum price for this property. If several participants in the auction for the sale of the debtor's property through a public offer submitted, within the prescribed period, applications containing equal proposals for the price of the debtor's property, but not lower than the initial sale price of the debtor's property established for a certain period of the auction, the right to acquire the debtor's property belongs to the participant tender, who was the first to submit an application within the established period for participation in the tender for the sale of the debtor's property through a public offer.
Term and procedure for signing the purchase and sale agreement: Within 5 days from the date of summing up the results of the auction, the bankruptcy trustee sends the winner of the auction an offer to conclude a financial contract with a draft of this agreement attached. The DPA is concluded with the winning bidder within 5 days from the date of receipt of the proposal to conclude the DPA.
Deadlines for payment of the purchase price based on the results of the auction: A deposit in the amount of 10% of the lot price valid at the time of filing the application must be credited no later than the last day of the price period in which the application was submitted (for a public offer) to a special account : recipient: Kosam LLC; account number 40702810100770003567 at PJSC Bank Uralsib, Moscow; BIC 044525787, contract number 30101810100000000787. In the purpose of payment, indicate: lot number and code of the auction for participation in which a deposit is paid. The winner is obliged to pay within 30 days from the date of conclusion of the contract the price determined at the auction, minus the previously paid deposit according to the details: recipient: recipient: Kosam LLC; account number 40702810500770003565 at PJSC Bank Uralsib, Moscow; BIC 044525787, c/s 30101810100000000787.
