Mini tractors Scout: characteristics and review of models

The Scout T-18 minitractor can be called a new product on the market, since mass production of this model was launched recently. The tractor belongs to the segment of 18-horsepower special vehicles, but it has very compact dimensions and increased efficiency, which is typical only for equipment with a capacity of 10-15 horsepower. Unlike its predecessor, the machine has increased power and expanded operational capabilities, which makes the mini tractor quite a serious competitor in the market.

During development, the manufacturer placed the main emphasis on performance indicators, thanks to which the machine can quite easily cope with very labor-intensive agricultural and municipal tasks.

Among the model range of the manufacturer Scout, the T-18 is the only vehicle on which it was originally planned to install dual rear wheels, but as testing showed, such a solution would not always be effective and therefore single wheels with wide tires were installed instead. The rear wheels have a dimension of 9.50-R16, which guarantees high maneuverability, optimal weight distribution throughout the structure, and also improves maneuverability. For example, wheels size 6.50-R16 are 35 percent inferior in this indicator. But besides all this, the installation of larger wheels led to a decrease in vibrations, which had a positive effect on the driver’s work comfort.

Purpose

The Scout T-18 minitractor can carry out complete cultivation of a land plot of up to three hectares. With a minimal set of attachments, the machine plows various soils, processes planted plants, harvests and transports grown products for further processing.

Also, this mini tractor can provide significant assistance in weeding vegetables and various grain crops, hilling, fertilizing and watering, and in preparing various feeds. Due to its compact dimensions, the model is often used in hard-to-reach street and courtyard areas, where it removes snow and debris.

The tractor is equipped with a locking center differential, which, together with the increased ground clearance and deep tread of the tires used, has significantly increased cross-country ability. Due to this, the mini tractor can process low-growing plants and also work on heavy soils.

Video

Among other features of the Scout 15 walk-behind tractor, the following should be highlighted:

• multifunctionality;
• large wheels with aggressive tread;
• wide selection of attachments;
• presence of an electric starter;
• high ground clearance;
• simplicity of design and control;
• rich basic equipment;
• efficiency;
• ability to work with any type of soil;
• high ground clearance;
• the presence of a headlight that allows you to work in the dark;
• the ability to unlock the drive axle (separate for each wheel), providing excellent maneuverability.

The basic package (in addition to the adapter chair) again includes a rotary cutter and a single-furrow plow. This equipment is quite sufficient for normal operation. Scout 15 DE has the functionality of a variety of specialized devices and, with thoughtful operation, can easily replace many of them.

Specifications

Thanks to the even distribution of the weight of the Scout T18 minitractor, the designers managed to achieve the following advantages:

• Reducing soil load;
• Add stability indicators when driving on uneven surfaces;
• Improved traction characteristics.

Minitractor Scout T18

More detailed technical characteristics are presented in the table:

Engine

• The type of engine installed is diesel, in-line.
• The brand of the installed engine is ZS1115.
• The manufacturer of the installed engine is KAMA.
• Number of cylinders: 1 cylinder.
• Rated output power is 15 horsepower/11 kilowatts.
• Maximum output power is 18 horsepower/13.3 kilowatts.
• The highest crankshaft rotation speed is 2200 rpm.
• The working volume of the cylinder is 1106 cubic meters.
• Type of cooling system - liquid combined with air.
• Starting system type: electric starter or manual.
• Type of fuel supply system: electronic.
• Type of lubrication system: combined.
• The diameter of the cylinders is 110 millimeters.
• The piston stroke is 116.5 millimeters.
• The structural length of the unit is 940 millimeters.
• The structural width of the unit is 700 millimeters.
• The structural height of the unit is 600 millimeters.
• The structural weight of the unit is 172 kilograms.

Transmission

• The type of gearbox installed is mechanical.
• Drive type: pair of V-belts B3150.
• The differential lock is mechanical.
• Number of forward gears - 6.
• Number of reverse gears - 2.
• Clutch type - dry, single-disc friction in constant continuous contact.

PTO

• The rear PTO type is gear-type.
• The front PTO type is belt driven.
• The number of power take-off shaft speeds is 2.
• Control is mechanical.
• The lowest PTO rotation speed is 540 rpm.
• The highest PTO rotation speed is 1176 rpm.

Performance characteristics

• The structural weight of the mini tractor (without attachments) is 690 kilograms.
• The structural weight of the minitractor (with a tillage cutter) is 740 kilograms.
• The type of hydraulic system used is three-point, universal.
• Brake type: dry, mechanical drum.
• The lowest speed of independent forward movement is 2 kilometers per hour.
• The highest speed of independent forward movement is 35 kilometers per hour.
• The lowest speed for independent movement in reverse is 3 kilometers per hour.
• The highest speed of independent movement in reverse is 15 kilometers per hour.
• The lowest fuel consumption per hour of operation is 700 grams.
• The highest fuel consumption per hour of operation is 1.5 liters.
• The capacity of the fuel tank is 9 liters.
• The front wheel size is 5.00-R12.
• The rear wheel size is 9.50-R16.
• The width of the area to be processed is 1200 millimeters.
• The depth of processing of the area is 170 millimeters.

Chassis

The tractor chassis has a 4x2 formula - with driving rear wheels. The range of track adjustment is within 110-140 cm. Wide-profile pneumatic tires measuring 9.5-16 inches provide effective traction with the ground and a smooth ride when moving the tractor unit through areas with problematic micro-relief.

The tractor driver's workplace provides the necessary set of amenities. The list includes an adjustable seat, ergonomic placement of the steering column and all controls, an informative instrument panel, and modern lighting equipment.

Hydraulic system

Modified on-board hydraulics have a large reserve of performance and load capacity. The presence of a two-vector hydraulic distributor with a floating mode makes it possible to control two hydraulic attachments in parallel.

The most popular additional attachments:

• potato planter;
• various seeders;
• potato digger;
• mowing machine;
• blade shovel;
• snow blower;
• rake;
• plow;
• additional cutters;
• cart;
• various adapters.

The cost of additional equipment for the Scout 15 walk-behind tractor is slightly higher than for other Chinese devices. However, the high quality fully justifies such an investment. It is noteworthy that there are many types of specific devices for this technique. Thus, the walk-behind tractor can be used with a wood splitter powered by a power take-off shaft.

Scout 15 is one of the most reliable devices. However, it also needs maintenance. Immediately after purchase, the walk-behind tractor should be run in. This process usually takes from 10 to 15 hours. First of all, you need to add oil and fuel to the required level. After this, the engine is started for the first time and warmed up (5-10 minutes). Upon completion of this stage, work is performed in different gears. Here it is important to pay attention to the operation of the equipment - it should be smooth without failures. After the first hour of operation, you should start using the walk-behind tractor on the site. At the same time, it is not recommended to give maximum loads during the break-in period. After its completion, it is necessary to perform maintenance on the walk-behind tractor.

Device

If we draw a parallel with cars of a similar class, the Scout T18 is distinguished by a small turning radius, an additionally reinforced frame and the ability to set the size of the rear and front tracks.

To make it easier for the owner to carry out work, a comfortable seat with a shock absorber (which can be additionally adjusted in height), an information dashboard, high-quality headlights and a thoughtful arrangement of all control levers were installed.

Attachments

The Scout T-18 minitractor is equipped with a rototiller, the width of which is 120 cm. However, the following attachments can be attached to the unit:

• Brush.
• The blade is hydraulic.
• Snow blower.
• Plow, single-body and double-body.
• Potato planter.
• Triple hiller.
• Potato digger.
• Weeding and hilling kit.
• Seeder.
• Garlic planter.
• Trailer.
• Mower.
• Rake.

Prices

The cost of popular models is:

• T-12 - 168 thousand rubles;
• T-15 - 187.2 thousand rubles;
• T-18 - 184.9 thousand rubles;
• T-24 - 272 thousand rubles.

The tractors are equipped with a soil tiller. Installing a canvas canopy over the operator’s workplace will cost 10 thousand rubles. When tractors are sold by official representatives, preparation is offered, including checking fluid levels and tightening threaded connections. The cost of pre-sale preparation is 4 thousand rubles.

On the secondary market, the cost of Scout tractors starts from 60 thousand rubles. For this price, cars with a lot of operating time are sold, requiring repair of the frame and transmission units. Tractors in good condition are valued at 120 thousand rubles and more.

Repair features

The hood of the minitractor opens quite wide, which provides full access to the power plant and other equally important elements and components. The owner can independently carry out full maintenance, and if he has experience with engine repairs, then a major overhaul. The cost of spare parts sometimes varies, but is still very affordable. They are also widespread, so finding them will not be difficult. Nowadays, many service centers provide various services, ranging from diagnostics to complete repair of the entire machine, which in some cases can be very helpful.

Reviews

• The cost of the Scout 15 DE walk-behind tractor is quite high. Today it can be purchased for 80,000-90,000 rubles. However, the functionality it provides is worth it. The device is capable of working without interruption for a long time, and is superior in power to almost all existing models. Naturally, for a small plot of land such special equipment will be a real “dinosaur” and is unlikely to pay for itself. However, for cultivating large areas of land, the Scout 15 DE is ideal. The powerful 15-horsepower engine confidently takes even virgin soil. Moreover, processing proceeds at a decent speed. It took me several hours to cover the entire plot (about 40 acres). Fuel consumption remains very acceptable. Despite the Chinese assembly, the walk-behind tractor works properly and does not cause any special problems. I recommend it to anyone who is looking for a reliable assistant to perform large volumes of work.
• I plow quite a lot during the season. On your own plot there are about 30 acres and neighboring land. again, about another 5-10 acres of virgin land comes out. I carry out all the work using a Scout 15 walk-behind tractor. The device is very successful. For 10 acres it takes about 5-6 liters of diesel fuel. The walk-behind tractor goes very well and sometimes even virgin soil can be processed the first time. Management cannot be called easy. The weight of more than 300 kg makes itself felt. This requires serious effort. In terms of performance and reliability, the Scout 15 is very good. He does everything quickly and efficiently.
• I have been using the Scout 15 walk-behind tractor for 3 years. I use it to do a lot of work on the site. The cutter functions perfectly, and with the plow the machine becomes incredibly productive. There are no problems with spare parts yet. There were no breakdowns, and consumables are sold in regular stores in large quantities. The electric starter works properly and the engine always starts the first time. So far I'm happy with absolutely everything about this device.
• The Scout 15 walk-behind tractor is a real beast. It is intended for large areas and is not suitable for those who have not used such equipment before. The weight of the device is over 300 kg, and the motor power is 15 hp. This allows the equipment to process any soil quite quickly. I use a walk-behind tractor with a cart. Moreover, sometimes I carry up to 1.5 tons of cargo; the Scout 15 confidently pulls such a weight. I am completely satisfied with the unit, no problems have arisen so far.

Advantages

The widely functional Garden Scout T18 station wagon is compatible with more than 50 types of mounted and trailed equipment for various purposes, including walk-behind tractors.

This is facilitated by a universal linkage mechanism, efficient on-board hydraulics, and the ability to activate working parts using a power take-off mechanism.

The list of advantages:

• simple and reliable machine design;
• compatibility with attachments from other manufacturers, including models from previous years;
• free access to systems and units for maintenance and repair work;
• economical application and stability of operating parameters over a long designated and operational service life.

Review of mini tractors Scout

is an enterprise that produces equipment for agricultural and municipal needs.
Jointly produced products – Chinese spare parts and Russian assembly – are entering the Russian market. This is to some extent a winning combination, because while maintaining high quality, the equipment is relatively inexpensive. The Scout company presents its products in many cities of Russia. Thanks to a wide range of not only working equipment, but also attachments, farmers can quickly and efficiently carry out various work on their site.

The well-deserved demand for products is due to several reasons:

• Competitive cost of products.
• The delivery set is compiled at the buyer's request, i.e. additional components and assemblies to choose from.
• The technology is a product of experience and modern progress, and therefore in some respects it may be superior to known analogues.
• Component parts are presented in a wide range.