The use of special equipment in various fields has long ceased to be rare. The capabilities of this unit allow you to perform the maximum amount of work in a short time. The design of the Chinese-made mobile wheeled truck crane XCMG was created using the latest hydraulic systems, which received 6 patents in the homeland of the company.
The excellent cross-country ability and adaptability of this unit of equipment to the most unfavorable conditions significantly expands the possibilities of using the machine in various industries. High stability under heavy loads is ensured by a low center of gravity. All these data explain the popularity of this truck crane.
xcmg qy50k crane manual
For stable operation of any equipment, it is necessary to follow the rules prescribed in the operating recommendations. It is strictly forbidden to carry out crane work without special training of personnel. Another important point is the serviceability of the equipment, which will be the key to safety.
Before you begin any manipulations, you should check the passages on the site and the distance to the work site so that the crane fits in height, width and length. You should also be sure to determine where the power lines are so that you don’t catch them with an arrow while working.
Also during preparation, you need to take into account the weight of the load in order to correctly determine the crane model. The XCMG QY50k crane is designed for a maximum load of 50 tons.
Truck crane QY50K - general information
The product in question is one of the advanced special equipment of the Chinese automobile industry. He has six state patents, but in essence it is a synthesis of the technologies of Western mechanical engineering monsters and Chinese engineers. Since 2008, the equipment has been equipped with an environmentally friendly engine that meets European Euro 3 standards.
Key Points of Crane Operation
The manufacturer's manual provides the following recommendations for using the crane:
- Before turning on the main power, all valve control handles should be in the neutral position.
- Before starting work, install the boom lift and torque limiter.
- When using equipment in winter, be sure to warm up the machine at idle for 20 minutes so that all systems are in working condition at the required temperature.
- Manipulations can be performed after installing the machine in a strictly horizontal position on solid, level ground. In the case of an uneven surface, defects are compensated with the help of wooden flooring.
- After installing the outrigger outrigger, make sure that the wheels are lifted off the road surface.
In addition to the preparation rules, the regulations regarding crane maintenance should be strictly observed:
- Before starting work, check the level of fuel in the tank and hydraulic oil in the system.
- Systematically check the reliability of fastening of all main components of the machine.
- Regularly pay attention to anti-seize lubricants, eliminating their deficiency.
- Systematically clean the filters of grease sedimentation tanks.
- Under no circumstances should you carry out repairs on equipment with the engine running.
- If, during lifting work, the devices display a hydraulic oil heating value above 80˚, stop all manipulations and eliminate the cause of overheating.
- When moving a truck crane between work sites, it is imperative to attach a load hook.
Following these recommendations for using a truck crane will ensure a long service life of the equipment, protect against breakdowns and minimize emergencies and accidents.
Chassis Specifications
Category | Paragraph | Unit change | Options | |
dimensions | Full Length | mm | 13100 | |
Full Width | mm | 2750 | ||
Full Height | mm | 3350 | ||
Wheelbase | Axis 1, Axis 2 | mm | 1520 | |
Axis 2, Axis 3 | mm | 3815 | ||
Axis 3, Axis 4 | mm | 1350 | ||
Weight | Gross weight in transport position | kg | 38580 | |
Cart load | Front trolley | kg | 12950 | |
Rear trolley | kg | 25630 | ||
Driving performance | Speed | maximum | km/h | 66 |
Minimum possible | km/h | 2,7 | ||
Turning diameter | Minimum | m | 24 | |
At the crane boom head | m | 26,8 | ||
Ground clearance | mm | 285 | ||
Front overhang angle | hail | 16 | ||
Rear overhang angle | hail | 11 | ||
Braking distances | m | 10 | ||
(at a speed of 30 km/h with maximum load) | ||||
Maximum climbability | hail | 27 | ||
Fuel consumption | l | 42 | ||
Engine | Engine model | WD 615067 A | ||
Engine power | kW/(rpm) | 206/2200 | ||
Engine torque | Nm/(rpm) | 1100/1400 | ||
Rotation frequency | rpm | 2200 |
Wheeled truck crane XCMG QY50K5S
Parameter | Unit measurements | Meaning | ||
Dimensions | Length | mm | 13750 | |
Width | mm | 2800 | ||
Height | mm | 3520 | ||
Wheelbase | front axles | mm | 1520 | |
medium bridges | mm | 3815 | ||
rear axles | mm | 1350 | ||
Weight | Transport weight | kg | 41000 | |
Axle load | Front | kg | 15000 | |
Rear | kg | 28000 | ||
Ride quality | Travel speed | Maximum | km/h | 80 |
Minimum | km/h | 2,7 | ||
Turning radius | Minimum | m | 24 | |
By arrow | m | 26.8 | ||
Ground clearance | mm | 291 | ||
Forward angle of attack | (°) | 16 | ||
Rear angle of attack | (°) | 16 | ||
Braking distance at a speed of 30 km/h | m | 10 | ||
Gradeability max. | % | 27 | ||
Fuel consumption per 100 km | l | 36 | ||
Engine | model | WD615.334 | ||
Power/speed | kW/rev. min | 247/2200 |
Environmental class | EURO-4 | |||
Options | Maximum load capacity | tn | 50 | |
Minimum operating radius | m | 3 | ||
Turning radius | m | 3.482 | ||
Max. moment | Main boom | KN.m | 1764 | |
Full boom | KN.m | 823 | ||
Distance between supports | length | m | 5.65 | |
width | m | 6.6 | ||
Lifting height | Main boom | m | 11.3 | |
Full boom | m | 42.7 | ||
Boom+jib | m | 57.7 | ||
Operation speed | Boom raising time | With | 88 | |
Extension time | With | 180 | ||
Turning speed | rpm | 2 | ||
Lifting speed | winch | full load | m/min | 85 |
without load | m/min | 110 | ||
Auxiliary winch | full load | m/min | 85 | |
without load | m/min | 110 |
Description of the XCMG QY50K5S wheeled truck crane
XCMG mobile wheel crane is designed using a completely new hydraulic system, which has received 6 government patents in China. The XCMG wheeled truck crane is characterized by excellent cross-country ability. The low center of gravity provides good stability both during movement and when performing crane work.
In the XCMG wheeled truck crane, the boom is lifted by one hydraulic cylinder; the sections are pulled out thanks to the operation of one hydraulic cylinder and a special block system. An additional outrigger installed above the driver's cab increases stability and expands the range of work performed. and auxiliary winches can be operated simultaneously or separately.
Excellent performance of the XCMG truck crane is ensured by a powerful, economical engine that meets Euro-4 environmental standards. Maneuverability and high levels of dynamism are the result of the use of high-tech materials, which made it possible to reduce the weight of the equipment without compromising performance characteristics.
The slewing system implemented in the XCMG crane design has a free sliding function. This facilitates load distribution and makes it easy to adapt the clutch clearance to suit current needs.
XCMG wheeled mobile cranes are equipped with a full-size crane operator's cab with wide visibility, which makes crane operations easier. To ensure comfortable conditions for the crane operator, the cabin is equipped with an autonomous climate control system. The crane driver's cabin also has a heating system.
On the armrest of the operator's chair there are two joysticks that control the crane. Their high sensitivity allows complex crane operations to be performed without effort on the part of the operator.
The latest hydraulic control system ensures high accuracy of loading and unloading operations. XCMG wheeled truck cranes have a minimum operating radius of 3 meters.
Additional reliability during control is provided by an additional hydraulic housing, an anti-cavitation oil filter device and other high-tech features.
The safety of the XCMG truck crane is ensured by a modern system that combines a number of engineering solutions aimed at increasing the efficiency and reliability of crane operations. The system includes: a maximum load lift limiter, a cable free play and load torque clamp, and other safety elements. Installation of additional safety devices is allowed.
Operating instructions for XCMG QY50K5S wheeled truck crane
Download manual - technical documentation
Price of XCMG QY50K5S wheeled truck crane
The XCMG QY50K5S wheeled truck crane is sold by an official dealer in Russia.
To buy, find out the price by phone
Services and rental of wheeled truck crane XCMG QY50K5S
Find out the cost of rental and services of a wheeled truck crane XCMG QY50K5S by phone
Spare parts for wheeled truck crane XCMG QY50K5S
Spare parts for XCMG wheeled truck crane
Technical specifications for lifting operations
Category | Paragraph | Unit change | Options | |
Lifting work | Maximum load capacity | T | 50 | |
Minimum working radius (reach) | m | 3 | ||
Minimum radius at the tail of the counterweight | m | 3,485 | ||
Maximum load moment | Main boom | kN.m | 1764 | |
Fully extended boom | kN.m | 823 | ||
Fully extended boom and jib | kN.m | 492,8 | ||
Distance between outriggers | Longitudinal distance | m | 5,65 | |
Transverse distance | m | 6,6 | ||
Lifting height | Main boom | m | 10,75 | |
Fully extended boom | m | 40 | ||
Fully extended boom and jib | m | 55,8 | ||
Working speed | Main boom raising time | s | 88 | |
Boom full extension time | s | 180 | ||
Maximum turning speed | RPM | 2 | ||
Lifting speed | Main winch | Load limit | m/minute | 85 |
Without load | m/minute | 110 | ||
Auxiliary winch | Load limit | m/minute | 80 | |
Without load | m/minute | 110 | ||
Noise limit | External noise | Decibel (A) | 118 | |
In working position | Decibel (A) | 90 |
Load height characteristics for all sections of the main boom
Working radius (reach), m | Boom length | ||||
Folded boom (10.7 m) | boom (18.05 m.) | Arrow | Extended boom (40.10 m.) | ||
(25.40 m.) | (32.75 m.) | ||||
3 | 50000 | ||||
3,5 | 50000 | 31000 | |||
4 | 42500 | 29000 | |||
4,5 | 39500 | 28000 | 20000 | ||
5 | 36000 | 27000 | 19000 | ||
5,5 | 30300 | 24500 | 18500 | ||
6 | 25600 | 23000 | 18200 | 13600 | |
7 | 19400 | 18900 | 17000 | 13600 | |
8 | 15200 | 14600 | 15500 | 12500 | 8200 |
9 | 12100 | 11800 | 12800 | 11500 | 8200 |
10 | 9500 | 10600 | 10500 | 7600 | |
12 | 6800 | 7700 | 8200 | 6800 | |
14 | 4800 | 5800 | 6200 | 6000 | |
16 | 3400 | 4400 | 4800 | 5000 | |
18 | 3300 | 3800 | 4000 | ||
20 | 2500 | 3000 | 3200 | ||
22 | 1800 | 2300 | 2600 | ||
24 | 1800 | 2100 | |||
26 | 1300 | 1600 | |||
28 | 1200 | ||||
30 | 900 | ||||
Line parts | |||||
12 | 8 | 5 | 4 | 3 | |
Hook weight | |||||
515 kg. | |||||
Min. Boom angle | |||||
16,36 | 17,02 | 24,11 | 34,21 | 39,28 | |
Max. Boom angle | |||||
76,16 | 77,93 | 77,99 | 77,3 | ||
68,95 |
Full height ratings for jib jib
Boom angle | Boom 40.1 m. | |||||
Jib angle of XCMG QY 50 K truck crane | ||||||
0 | 15 | 30 | ||||
Jib 8.5m. | Gusek | Jib 8.5m. | Gusek | Jib 8.5m. | Gusek | |
15.0 m | 15.0 m | 15.0 m | ||||
78 | 4000 | 2000 | 2700 | 1400 | 2440 | 1100 |
75 | 3600 | 2000 | 2500 | 1200 | 2300 | 1000 |
72 | 3200 | 1800 | 2300 | 1150 | 2200 | 990 |
70 | 2900 | 1700 | 2200 | 1100 | 2100 | 950 |
65 | 2300 | 1400 | 1900 | 950 | 1900 | 880 |
60 | 1800 | 1200 | 1600 | 800 | 1500 | 830 |
55 | 1000 | 800 | 900 | 700 | 850 | 600 |
50 | 450 | 400 | 350 |
see also
XCMG truck crane
XCMG QY16B XZJ5231JQZ16B (truck crane)
XCMG
More details
Manufacturer: | Xuzhou Construction Machinery Group Co., Ltd. (XCMG) (China) | ||
Name: | QY16B | Fuel: | diesel fuel |
Crane lifting capacity, t: | 16 | Total weight, kg: | 23370 |
Chassis: | XZJ5231JQZ16B | Wheelbase, mm: | 4025+1350 |
Engine: | SC7H245Q5 | Tires: | 11.00-20, 11.00R20 |
Power, kWt: | 180 | Axle loads, kg: | 6630/16740 |
XCMG QY130 XZJ5554JQZ130 (truck crane)
XCMG
More details
Manufacturer: | Xuzhou Construction Machinery Group Co., Ltd. (XCMG) (China) | ||
Name: | QY130 | Fuel: | diesel fuel |
Crane lifting capacity, t: | 130 | Total weight, kg: | 54990 |
Chassis: | XZJ5554JQZ130 | Wheelbase, mm: | 1920+3500+1420+1505 |
Engine: | ISM11E4 440; WP12.430… | Tires: | 12.00R24 |
Power, kWt: | 318; 316 | Axle loads, kg: | 9990/10000/13000/1300… |
XCMG QY8D XZJ5106JQZ8D (truck crane)
XCMG
More details
Manufacturer: | Xuzhou Construction Machinery Group Co., Ltd. (XCMG) (China) | ||
Name: | QY8D | Fuel: | diesel fuel |
Crane lifting capacity, t: | 8 | Total weight, kg: | 10490 |
Chassis: | EQ1110FD4GJ | Wheelbase, mm: | 3950, 4700 |
Engine: | ISF3.8s4141; YC4E140-… | Tires: | 9.00-20 |
Power, kWt: | 105; 103; 103; 103 | Axle loads, kg: | 2800/7690 |
show all Other XCMG truck cranes